High-definition link for evo id5,id6 with oem touch (24 pages)
Summary of Contents for INDIWORK IW04-MB14
Page 1
Release Date: 2015 - 11 - 12 Instruction Manual High-Definition Link for Mercedes-Benz IW04-MB14 Model Name IW04-MB14 Latest Firmware Date 2015 - 06 - 09 Manual Version Rev. 3.6 Language English...
Navigation(GPS) box - related • When you connect the power wires(B+, ACC) to the navigation(GPS) box, the ‘NAVI 12V OUT' wire supported by IW04-MB14 should be spliced with an ACC wire of navigation box. • After installation is done, select an applicable navigation(GPS) box model in the 'Navigation model selection menu' of setting mode.
Dimension Width: 142 mm Height: 22 mm Length: 91 mm ⓐ ⓑ ⓒ ⓓ ⓔ Exterior ⓐ DIP SWITCH ⓑ AV IN / OUT ⓒ TOUCH IN ⓓ MODE ⓔ POWER / CAN ⓕ HDMI IN ⓖ 5V USB POWER ⓗ...
Power / CAN Cable LVDS Cable LVDS PCB HDMI Cable AV IN / OUT Cable 5-pin Micro USB Cable (For LVDS) Optional Parts (sold separately at the indiwork) HDMI Cable HDMI Extender Mode Switch (Male to Male) (For stick type HDMI device)
HDMI Connection Diagram HDMI Device HDMI Device HDMI IN 5V USB NAVI IN UART I/F LVDS OUT HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER POWER HDMI HDMI HDMI HDMI (5V-1A Power output for HDMI Device) (5V-1A Power output for HDMI Device) (Male) (Female) (HDMI Extender)
Navigation Connection Diagram(Type A) Navigation Connection Diagram(Type B) Navigation(GPS) Box Navigation(GPS) Box HDMI IN 5V USB NAVI IN UART I/F LVDS OUT HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER POWER TOUCH IN HDMI HDMI Touch screen panel Touch screen panel HDMI Gender...
MYVI Type B South Korea MS1400 Digital OFF(↓): 1, 2, 3 HDMI Cable ON(↑) : 4 (HDMI to HDMI) • The 'IW04-MB14(HD-Link)' supports navigation(GPS) box models equipped with 'Digital video output'. • It does not support the 'RGB video signals'.
LVDS Connection Diagram LVDS Connection HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER COMAND APS NTG 5.0 - Head Unit HDMI (Blue ‘DISP port’) (Provided LVDS Cable) • 'Genuine(OEM) LVDS connector' should be connected to 'LVDS IN / OUT PCB'. OEM Monitor •...
Hazard Module Connection (‘Smart Drive’ function of ‘N-Link’ Navigation) POWER / CAN AV IN / OUT DIP SWITCH MODE TOUCH-IN Hazard button(W205) 8-pin Hazard connector(W205) Old Version Module New Version Module Hazard Hazard Module Module (4-Pin) (3-Pin) Pin # 4 = Hazard(-) (Black/Red) IR IN (20 cm) (100 cm)
Body Connector specifications MODE TOUCH-IN DIP SWITCH AV IN / OUT POWER / CAN 1 2 3 4 Length: 20 cm Length: 100 cm Length: 150 cm Length: 150 cm BATTERY POWER INPUT RV-CAM VIDEO INPUT GND(RV-CAM VIDEO) GND INPUT RV-CAM POWER OUT GND OUTPUT(RV-CAM) GND OUTPUT...
< OEM → AV2 > Press the button 4 times. If you visit car service center, you can lock the all System functions of IW04-MB14. Locking / Press the button 10 seconds long. It is only possible to use the OEM functions under it...
< OEM → AV2 > Press the button 4 times. If you visit car service center, you can lock the all System functions of IW04-MB14. Locking / Press the button 10 seconds long. It is only possible to use the OEM functions under it...
Settings Button Function Back( Back to previous menu when press the button short. ★ Enter into the setting menu when you press the button Bookmark( 5 seconds long. *W205(C-Class) Up, Down, Left, Right Move the menu-pointer and adjust the setting values. Selection( Select the setting menu and setting values.
Settings 4. Rear view camera settings - Parking guide lines = Adjust position of parking guide lines and select the lines ‘ON or OFF’. - Parking distance control = Adjust position of parking distance control sensors to ‘LEFT or RIGHT’ and select the PDC ‘ON or OFF’. - Image display = Adjust the values of brightness and contrast Red-Green-Blue colors of Rear view camera display.
Settings 6. Automatic activation function(AV1) - Shift gear from reverse to drive - Shift gear from parking to drive * When you shift gear ‘from reverse to drive’ or ‘from parking to drive’, it just works automatically during the activation time you selected. 7.
- Factory default = Reset all setting values to factory default setting. 9. System information - Mode name: IW04-MB14 - Firmware date: 2015 - 06 - 09 (Latest firmware date) - = You can check the current firmware version date.
Settings 10. Information of Dip switch settings * You can check the current positions of dip switch settings. ex 1) ex 2) Actual DIP switch values. (→) Actual DIP switch values. (→) Appears on the setting menu. (↓) Appears on the setting menu. (↓)