Herpstat 1 Basic User Manual

Getting the most out of your Herpstat
(Troubleshooting)
When setting up a new environment allow a minimum of one hour for the temperature to stabilize. Keep in
mind that all items in the enclosure are warming up including the enclosure walls. Probe placement will require
experimentation to achieve proper temperature regulation.
If after an hour of initial regulation the temperature does not reach within a degree of the target temperature
this is an indication of insufficient heating source. Add an additional heat device to the enclosure or switch to a
higher wattage heat device. Do not exceed the maximum watts per output.
The Herpstat has a user replaceable fuse. If the Herpstat appears to not operate while being plugged in the
fuse may have been damaged by a voltage spike or overload. Disconnect all cables to the unit including the
power. Flip the device upside down and looking at the back of the device the fuse holder will be below where
the power cord plugs into the device. Use a flathead screwdriver and gently insert the tip into the recess and
then lightly twist the handle to pop open the fuse drawer. A spare fuse is included and will be loose in this
drawer. Flip the device back upright (catching the spare) and use the blade of the screw driver to lightly push
against the metal of one side of the fuse to remove it. Insert the new fuse and close the drawer fully to finish
the process. IMPORTANT: Replace with correct fuse! The Herpstat 1 Basic uses a 6.3 amp 5x20mm fast
acting fuse. Never bypass the safety fuse or use a larger fuse as it can become a serious safety hazard.
Additional fuses can be purchased through Spyder Robotics online webstore. We recommend keeping spares on
hand to avoid potential downtime should this scenario occur.
(Getting the most out of your Herpstat continued...)
Should the device not work as expected it's possible one of the menu settings was set incorrectly. It may be
easier to reset the device to its factory default settings than to figure out which setting is causing the issue. To
do this enter the menu and perform the Master Reset option under the System Settings menu.
Do not cover the probe tip with aluminum tape. This will cause false readings and poor regulation.
If possible route the probe wire so that it is not in direct contact with the 120vac cables going to the heating
devices. Preferably leave at least a few inches between the probe wires and the AC lines to avoid cross
talk/electrical interference issues.

Getting Help

Questions or comments can be e-mailed to:
support@herpstat.com
To purchase accessories please visit us on the web at:
http://www.spyderrobotics.com
1 Year Limited Warranty
Spyder Robotics LLC warrants this product to be free from defects in workmanship and material for a period of
one year from the date of purchase by the original purchaser. The warranty period shall not extend beyond 3
years from the date Spyder Robotics LLC shipped the product. During this warranty period Spyder Robotics LLC
will repair or replace, at its option, any component parts that in its opinion prove to be defective. Replacement
parts may be new or serviceable used parts at Spyder Robotics LLC option, of equal or better quality to those
being replaced. This warranty does not extend and shall not apply to products that have been subjected to
misuse, neglect, accident, or improper installation.
THIS LIMITED WARRANTY AND REMEDY ARE EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES
EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MECHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL SPYDER ROBOTICS LLC BE LIABLE FOR LOST
PROFITS, LOSS OF GOODWILL, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES.
If you return your product to Spyder Robotics LLC for warranty service, proof of purchase may be required. A
Return Material Authorization (RMA) number must be obtained prior to the return. Spyder Robotics LLC is not
responsible for material returned without the RMA number clearly printed on the outside of the shipping
container. To request an RMA number, contact Spyder Robotics LLC with the description of failure, serial
number of device, and date of purchase via e-mail at returns@spyderrobotics.com.
©2012 Spyder Robotics LLC
http://www.spyderrobotics.com
Thank you for choosing the Herpstat digital proportional thermostat. This product
offers the following features:
 Proportional heating constantly monitors and adjusts amount of heat necessary to maintain a target
temperature (usable range from 40˚F to 150˚F or 4˚C to 65˚C).
 Soft startup slowly applies power during initial warm-ups.
 Configurable for Heating, Cooling, Lighting.
 Lighting can simulate sunrise/sunset and moonlight.
 User selectable temperature and light ramping allows day to night changes to occur slowly.
 Sensor Matching allows the user to digitally calibrate the sensor output to match other equipment.
 Auto Power Matching constantly adjusts the power output curve to match the enclosures efficiency.
 Individually selectable day/night schedules.
 High/Low temperature tracking helps monitor heating system and enclosure efficiency.
 User adjustable High/Low temperature threshold alarms.
 Precision temperature sensors with an internal resolution of .1125 ˚F and are accurate to ± .9 ˚F
 Display and setting in tenths of a degree.
 Security Passcode option deters vandals.
 Settings retained in memory even if power is lost. *
 Power Outage detection/tracking.
 Temperature can be set/displayed in Fahrenheit or Celsius.
 Easy to read backlit LCD display.
 12 ft removable sensor allows for easy replacement if necessary.
 User replaceable fuse.
 Audible alarm system
 Internal error detection shuts off heat if sensor fails or is disconnected.
 700 total watt output
manual-HS313
 1 year limited warranty
2.23.2018
* Software clock is reset and features requiring the clock are disabled on power loss.
Herpstat 1 Basic
User's Manual
www.spyderrobotics.com