Advertisement
Page 2
ON/OFF footswitch: (see #1 on above diagrams) When pedal is ON, the LED (#4) will be lit. The ST-2 has Hi-Resolution JFET buffered-bypass which will still drive long cable lengths,
even when turned OFF. I recommend placing the ST-2 late (or last) in your chain of pedals. The VOLUME knob will not be active when the pedal is turned OFF, but you will still see the
speed LED's (# 6) flashing to the RATE you have chosen. This allows you to set up your desired Tempo when the pedal is turned off.
VOLUME knob: (#3) Controls the Level when the pedal is turned ON, only. CLEAN BOOST TRICK: Turn the MIX knob full counter clockwise (CCW) and you can use the ST-2 as a
clean boost pedal, getting as much as 15dB boost when pedal is turned on, depending on where you set the VOLUME knob.
RATE knob: (#7) This knob controls the RATE (speed) of the modulation along with the TAP TEMPO footswitch. Any changes made using the RATE knob will cancel the rate chosen by
the TAP TEMPO switch. Consequently, any changes made using the TAP TEMPO switch will cancel the rate chosen by the RATE knob.
RATE LEDs: (#6) These LEDs flash with the chosen tempo whether the pedal is ON or OFF. This allows syncing the pedal's tempo to the song's tempo while the pedal is ON or OFF, a
crucial feature for live performing. These LED's will flash either opposite each other or in unison, depending on where the PHASE CORRELATION knob (#8) is set.
PHASE CORRELATION knob: (#8) Changes to the settings of this knob are only audible when you are running the in stereo. This proprietary feature allows any degree of relative phase
between the two tremolo circuits in the ST-2. With this knob turned full CCW, the LEDs will flash in unison showing that the ST-2's outputs are "in phase." Your amps will both modulate in
unison with no panning effect between them. If you turn this knob full CW the LEDs will flash opposite each other, making the outputs"out of phase," and you will experience 3D-like
True-Stereo imaging and autopanning. The real magic happens when you choose a setting somewhere in-between CW and CCW, this feature does not exist on any other stereo device in
the world and can make for awesome live and recorded performances!
WAVEFORM toggle switch: (#9) There are three selectable waveforms on the ST-2. SINE is for your everyday natural Tremolo sounds.
SQUARE is for brutally abrupt and choppy at any speed even with hi-gain amps. WARBLE is not on ANY other tremolo pedal and is my favorite. I analyzed vintage univibe waveforms as
well as vintage Leslie rotating speakers and got a waveform so organic and rollicking that you may not want to stray too far from this setting.
TAP TEMPO footswitch: (#2): There are 2 ways to set the tempo on your ST-2. First way is by rotating the RATE knob (#7) to desired speed and the second (using your foot) with
theTAP TEMPO switch. The easiest way to use this is to simply tap 2 beats of the desired cadence on the footswitch, you only need 2 taps to set the RATE.
DOUBLE / HALF SPEED tap feature: You can double or halve the speed by holding down on the Tape Tempo footswitch for 3/4 of a second. You will stay in perfect tempo with the music
as this is an extremely precise division of time.
MONO LEFT (L) INPUT JACK: (see #10) Connect a (shielded ¼" mono) cable from your guitar into this jack. The unique design of the ST-2 allows for True-Stereo output even when
going in to this pedal mono.
RIGHT (R) INPUT JACK: (see #11) Connect a (shielded ¼" mono) cable into this jack only if you are placing the ST-2 after another effect that has stereo outs. Because the St-2 has two
completely separate Tremolo circuits inside, you will retain the True-stereo nature of your signal-chain whether the ST-2 is ON or OFF.
MONO LEFT (L) IOUTPUT JACK: (see #13) Use this jack for mono operation, plug a (shielded ¼" mono) cable from this going on to the input of subsequent effects or to your amplifier.
MONO RIGHT (R) OUTPUT JACK: (see #14) Connect a (shielded ¼" mono) cable into this jack if you are going in to another effect that has stereo inputs or if you are running stereo into
amplifiers. Warning! Running multiple amps can be dangerous or even fatal if you are not knowledgeable on how to properly ground all of the equipment involved, especially if there is a
Microphone/PA system that you will be using at the same time! Although I cannot recommend the use of a "ground-lift" adapter, using a 3 to 2 plug adapter (on only one of the amplifiers
and sometimes even the pedalboard) is something that is done by many people, who find that it can alleviate ground confusion & buzzing issues. Please research the internet and
including youtube.com before trying a stereo setup to make sure you are aware of the various techniques for successfully implementing a safe stereo amp setup.
DC Power Port: (#12) You may run this device on a high-quality regulated 9 -18VDC power supply (Noise-Free International IPS-18 is included) that offers at least 50mA of current.The
center-pin is configured to the industry-standard 2.1mm x 5.5mm barrel plug, "Negative to Center" configuration.
WARRANTY: Fulltone products carry a Limited 5 year Warranty to the original owner with proof of purchase that the product was bought from an Authorized Fulltone Dealer, and if it was
registered with us around the time of purchase via our registration portal at www.fulltone.com.The Warranty covers failure due to manufacturing errors only and is void if any mod or repair
is performed by anyone other than Fulltone and/or if we deem that any operator-caused abuse or damage has occurred, for example; the use of an incorrect power supply, a dropped
pedal, water damage, etc. Customer is always responsible for all shipping costs both to and from Fulltone. Do not attempt to call, instead, all repair issues are handled via contacting us
through the "Repair Inquiries" portal at www.fulltone.com. You will be required to troubleshoot the problem and to upload a video clearly showing the problem you are experiencing. After
we have deemed that a repair is necessary, we will email you an Acrobat PDF copy of our Return Authorization Form (RA Form) and print it out, fill out all information, and include it with
the device you are sending. Fulltone Musical Products Inc. is not responsible for any loss, injuries, or damages related to the use of our products. Use at your own risk.
Fulltone Musical Products Inc
.
11018 Washington Blvd. Culver City, CA 90232
for more info & demonstration videos go to www.Fulltone.com and www.YouTube.com/FulltoneEffects
for Sales, Repairs, Product Registration, or Technical questions go to www.Fulltone.com/contact-us
C
2018 FMP Inc. All Rights Reserved
Advertisement
