1. Manuals
  2. Brands
  3. f.a.l Manuals
  4. Lighting Equipment
  5. PF 964
  6. Instruction manual

f.a.l PF 964 Instruction Manual

Colour spot discharge lamp
Hide thumbs
Table of Contents

Advertisement

Quick Links

C
C
model:
PF 964
ATTENTION
This instruction manual contains important information about the installation and use
of the projector. Please read and follow these instruction carefully.
ATTENTION
Always ensure that the power to the projector is disconnected before opening the
projector or commencing any maintenance work.
F.A.L. S.R.L. VIA SVIZZERA 12/14 – 46042 CASTEL GOFFREDO (MN) ITALY
http://www.fal.it
O
L
O
U
O
L
O
U
D
I
S
C
H
A
D
I
S
C
H
A
Instruction Manual
COLOUR SPOT – Discharge lamp
R
S
P
R
S
P
R
G
E
L
A
R
G
E
L
A
O
T
O
T
M
P
M
P
fal@fal.it

Advertisement

Table of Contents
loading

Related Manuals for f.a.l PF 964

Summary of Contents for f.a.l PF 964

  • Page 1 Please read and follow these instruction carefully. ATTENTION Always ensure that the power to the projector is disconnected before opening the projector or commencing any maintenance work. F.A.L. S.R.L. VIA SVIZZERA 12/14 – 46042 CASTEL GOFFREDO (MN) ITALY http://www.fal.it fal@fal.it...

  • Page 2: Table Of Contents

    Please note that as part of F.A.L.'s ongoing commitment to continuous product development, specifications are subject to change without notice. Whilst every care is taken in the preparation of this manual F.A.L. reserves the right to change specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the...

  • Page 3: 01 - Safe Usage Of The Projector

    COLOUR SPOT - Discharge lamp 01 – SAFE USAGE OF THE PROJECTOR Do not attempt to dismantle and modify the projector. Do not allow contact with water or any other fluids, or metallic objects (IP 20). Do not install the projector in areas of high humidity. Not allowed to be mounted directly on inflammable surfaces.

  • Page 4: 03 - Fitting The Lamp

    COLOUR SPOT - Discharge lamp 03 – FITTING THE LAMP Open the lamp access hatch at the back of the projector by undoing the two knurled nuts (3). Unscrew the lamp holder as shown below, tilt the lamp holder sideways to facilitate insertion of the MSD 250 lamp.

  • Page 5: 06 - Control Connections

    COLOUR SPOT - Discharge lamp 06 – CONTROL CONNECTIONS The Colour Spot can accept digital control signals in DMX 512 (1990) format. Connection between controller and projector and between one projector and another must be made with 2 core screened cable, with each core having at least a 0.5mm cross section.

  • Page 6: 08 - Automatic Mode

    COLOUR SPOT - Discharge lamp To set the start address, turn “ON” the proper switches, so that the sum of their weight gives the desired number. The weight of each switch is shown in the following table. Switch ON Weight Example: start address 49 = switch ON 6 + 5 + 1 (32+16+1 = 49).

  • Page 7: 10 - Focus

    COLOUR SPOT - Discharge lamp 10 – FOCUS It is possible to move the lens for focusing the projector, simply twist the lens tube clockwise or anticlockwise to achieve focus. 11 – MAINTENANCE If the projectors lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in any way it must be replaced.

  • Page 8: 14 - Electrical Diagram

    COLOUR SPOT - Discharge lamp 14 – ELECTRICAL DIAGRAM...

  • Page 9: 15 - Technical Specifications

    COLOUR SPOT - Discharge lamp 15 – TECHNICAL SPECIFICATIONS POWER SUPPLY: 230V 50Hz or 60Hz. POWER 800VA at 230V. CONSUMPTION: LAMP: MSD 250 Socket Gy 9.5 life 2000 hours (manufacturer ratings). HSD 250 Socket Gy 9.5 life 2000 hours (manufacturer ratings). COLOURS: 8 dichroic colours + white and blackout.

Table of Contents