Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Elan EL-IP-OTF2-WH
Summary of Contents for Elan EL-IP-OTF2-WH
- Page 1 EL-IP-OTF2-WH Quick Start Guide...
- Page 2 QUICK START GUIDE BEGINNING USING THIS CAMERA IMPORTANT!! If you are installing an ELAN Cameras and/or ELAN NVR with an ELAN Controller, please refer to the “ELAN Surveillance” Integration Note for setup and software configuration. ELAN Integration Notes are served through the ELAN tools and on elanhomesystems.com/ dealer-resources.
- Page 3 EL-IP-OTF2-WH NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment...
- Page 4 QUICK START GUIDE Unit: mm PART DESCRIPTION & DIMENSIONS Upper cover Lens Infrared LED (IR LED) Light sensor RJ-45 Ethernet connector (supports PoE) Power jack (DC12V ±10%) Reset Wire (strip off the wire insulation if needed; after the camera is reset, cut off the bare wire) www.elanhomesystems.com...
-
Page 5: Installation
EL-IP-OTF2-WH INSTALLATION 1. Retrieve the camera and remove the bottom bracket from the upper cover with a hex key (FIG.1). Use the included screws (M4.0x25) through the holes marked as “a,” and fix the camera in the desired location (FIG.2 & FIG.3). - Page 6 QUICK START GUIDE 2. Attach the Ethernet and power cables to the RJ-45 connector and the DC-in connector, respectively (FIG.4). Connect the RJ-45 Ethernet cable with a waterproof connector First, remove the waterproof connector and unscrew the waterproof nut. Insert the Ethernet cable and connect to the RJ-45 connector with proper tools (FIG.5).
- Page 7 EL-IP-OTF2-WH 3. Secure the upper cover to the bottom bracket with a hex key FIG.7). 4. Adjust the pan, tilt, and azimuth of the camera to the desired location (FIG.8). After the adjustment, tighten the screws to complete the installation.
- Page 8 QUICK START GUIDE SYSTEM ARCHITECTURES For connecting EL-IP-OTF2-WH Camera series to the network, please follow one of the system architectures: (1). Use DC12V power adaptor and network switch connected to a network. EL-IP-OTF2-WH (2). Use with PoE of the network switch connected to the network.
-
Page 9: Emergency Factory Default
3. Search for the IP device using the IPScan software. 4. Start the IP device via an Internet browser. 5. Enter the default username “ELAN” and password “3526” to operate. NOTE: Cameras are configured to use DHCP by default but will revert to the default address 192.168.0.200 if a DHCP server is not available. -
Page 10: Software Requirements
QUICK START GUIDE SOFTWARE REQUIREMENTS Universal ActiveX software components are required for online display of MJPEG or H.264 Full HD video. When you log in to the IP camera from Internet Explorer, a security warning dialog box will prompt the installation of the Universal ActiveX plug-in. - Page 11 EL-IP-OTF2-WH INTERNET BROWSER SETTINGS & APPLICATION REQUIRED Make sure your Internet browser allows the signed ActiveX plug-in to work on your computer. To do this, open Internet Explorer and go to Tools-> Options-> Security Settings. Set “Download Signed ActiveX plug-in controls” to “Prompt” and “Run ActiveX control and plug-in”...
- Page 12 1 (707) 283-5900 - International 1 (707) 283-5901 - Fax web: elanhomesystems.com Core Brands, LLC, 1800 S McDowell Blvd., Petaluma, CA 94954, USA ©2017 Core Brands, LLC. All rights reserved. 10019569 Rev-A0, 11/2017 ELAN is a registered trademark of Core Brands, LLC.
Need help?
Do you have a question about the EL-IP-OTF2-WH and is the answer not in the manual?
Questions and answers