Safety 1st HS130 User Manual

Complete Magnetic Locking System
WARNING:
• ADULT ASSEMBLY REQUIRED. KEEP SMALL PARTS AWAY FROM CHILDREN DURING ASSEMBLY.
• Keep magnetic key out of reach of children.
• This product contains magnets. Swallowed magnets can stick together across intestines, causing serious infections
and death. Seek immediate medical attention if magnets are swallowed.
• For indoor use only.
• Toxic and dangerous substances, as well as sharp edged or pointed objects, should always be placed "high up" or
totally inaccessible to small children.
CAUTION:
• This product is not a toy. Do not allow children to play with it. When not in use, keep out of reach of children.
• This product is only a deterrent. It is not a substitute for proper adult supervision. Discontinue use when child becomes old enough to defeat it.
BEFORE YOU BEGIN:
• Read all instructions before installing.
• Keep these instructions for future use.
• Remove all contents from packaging and discard box, and/or poly
bags.
• Do not return this product to the place of purchase. If any parts
are missing, email consumer@djgusa.com, call Consumer Relations
at (800) 544-1108, or fax at (800) 207-8182. You can also visit our
website at www.safety1st.ca. Have the model number ready (HS130)
and date code (manufacture date) located on product.
Parts & Features
A
Catch
B
Lock
C
Lock/Unlock button
D
SecureTech lock indicator
TM
E
Magnetic key
F
Screws (4 per lock)
G
Installation template (1 per lock)
Determine Lock Placement
Cabinet Door and Drawer Types
There are many sizes, shapes and kinds of cabinet doors and drawer
fronts. To determine if our lock will work on your door/drawer follow
steps 1-8 below.
NOTE:
•
Doors with inset panels (Image A) may not have wide enough flat
surface.
•
Drawers with outer face panels (Image B) may not have enough room
to install this lock.
•
When locks don't fit at the top of the cabinet, they may fit at the side
(Image C).
1
Open door/drawer and choose a
possible location to install the lock.
Mark how far down the side of the
door/drawer or how far over on the
top of the door/drawer the lock will
be located (Figures 1a and 1b).
2
Close cabinet door/drawer and
mark your lock position on the
cabinet base (Figures 2a and 2b).
3
Peel paper (labeled ) off
1A
template (Figure 3).
©2011 Dorel Juvenile Group. All Rights Reserved. Tous droits réservés.
www.djgusa.com (800) 544-1108 www.safety1st.ca
Made in CHINA. Fabriqué en CHINE. Styles and colors may vary. Les styles et les couleurs peuvent varier.
Distributed by (distribué par) Dorel Juvenile Group, Inc., 2525 State St., Columbus, IN 47201-7494
Dorel Distribution Canada, 873 Hodge, St. Laurent, QC H4N 2B1 05/16/11 4358-5684
1a
1b
• Tools needed: Hand drill or power drill, 7/64" drill bit, Phillips head
screwdriver & pencil (not provided).
• Door/drawer geometry may prohibit use.
• Avoid close proximity to metal hardware or metal objects stored in
cabinets when planning product placement, as they might make it
difficult to operate the magnetic key properly.
• Avoid letting children see how you operate child safety devices.
Watching you disengage a lock or latch could enable them to learn
1A PEEL OFF
sooner how to defeat it.
3
SCREW HOLES
FOR LOCK
• Remove adhesive bumper pads on your cabinet doors only if they
interfere with installation or operation of these locks.
A
D
B
E
C
A
Panel frame
Inset frame
Drawer with outer face panel
2a
1
HS130 User Guide
1B PEEL OFF 1A PEEL OFF
FOLD
2
SCREW HOLES
FOR CATCH
SCREW HOLES
FOR LOCK
Green = Locked G
Red = Unlocked
PEEL OFF PEEL OFF
1B 1A
FOLD
F
2
SCREW HOLES
SCREW HOLES
FOR CATCH
FOR LOCK
B C
Inside
panel
2b
1B PEEL OFF
FOLD
2
SCREW HOLES
FOR CATCH
1B PEEL OFF
3
3
Top or side
3
1A PEEL OFF
3
SCREW HOLES
FOR LOCK