Table of Contents
Advertisement
Quick Links
DFC3301i-DFC4301i Series
Video & Duplex Data
Installation and Operations Manual
Model Number: DFC3301iTCZM2S - DFC4301iTDZM2F
Description: Digital Fiber Optic 1 Video Transmitters,
1 Video Receivers and duplex multiprotocol Data
Standalone and Card Units
DFC3301iRCZM2S - DFC4301iRDZM2F
DFC3301iRCZRS - DFC4301iRDZRF
DFC3301idRCZRS - DFC4301idRDZRF
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Dante DFC3301iTCZM2S
- Page 1 DFC3301i-DFC4301i Series Video & Duplex Data Installation and Operations Manual Model Number: DFC3301iTCZM2S - DFC4301iTDZM2F DFC3301iRCZM2S - DFC4301iRDZM2F DFC3301iRCZRS - DFC4301iRDZRF DFC3301idRCZRS - DFC4301idRDZRF Description: Digital Fiber Optic 1 Video Transmitters, 1 Video Receivers and duplex multiprotocol Data Standalone and Card Units...
-
Page 2: Table Of Contents
Table of Contents DFC3301i-DFC4301i Series Page About this manual standalone transmitter Video, duplex Data DFC3301iTCZM2S standalone 1 Video Transmitter, duplex data MM DFC4301iTDZM2F standalone 1 Video Transmitter, duplex data SM Features Application Diagram Attention Instructions Front Panel / Rear Panel View... -
Page 3: About This Manual Standalone Transmitter Video, Duplex Data
The explanation given in this manual can be applied to the following models unless noted otherwise. DFC3301iTCZM2S: Digital 1 Video Transmitter, duplex Data Transceiver, single fiber MM Standalone, 12VDC/24VAC ST DFC4301iTDZM2F: Digital 1 Video Transmitter, duplex Data... -
Page 4: Features
Features High speed synchronous digital transmission technology Modular construction design Highest optical dynamic range Power, Optical, Video, Data status indication Non-electromagnetic interference Transmission for extreme electromagnetic environment BNC video connector RJ45 data connector ST for MM and FC for SM optical connector Video DC Restoration Data interface: RS232 / RS422 / RS485 / Manchester / Biphase... -
Page 6: Attention
ATTENTION Do not exceed the range of power supply input 12VDC/24VAC. 8 dB for MM and 17 dB SM optical loss budget, the total loss in the optical fiber should be less than 8 dB for MM and 17 dB for MM, otherwise optical signal will not be present at the receiver. -
Page 7: Front Panel / Rear Panel View
Transmitter DFC3301iTCZM2S & 4301iTDZM2F The Standalone Transceiver is a field installable, compact unit providing 1 channel Video transmitter and duplex Data on 1 MM or SM fiber: The Front Panel The Rear Panel PORTS DEFINITION FRONT PANEL Video Input Port Optical Port ST &... -
Page 8: Data Rj-45 Configurations / Rs-232 Pinout Diagram
Data RJ45 Configuration as follows RS-232 (Pins only, no Dip Switch): PIN 2 RX PIN 3 TX PIN 4 GND RS-485 (2 Wire half duplex; Pins and Dip Switch): PIN 7 RX+/TX+ PIN 8 RX-/TX- and if at end of daisy chain RS-422 (Pins and Dip Switch): PIN 5 TX+ PIN 6 TX-... -
Page 9: Led Status Indicators
LED Status Indicators Power Indicator: ON to indicate the power applied, OFF to show that input voltage or the inner circuitry may be faulty Optical indicator: ON to indicate that the optical signal is transmitted Video indicator: ON to indicate video input Data indicator: ON to indicate data input/output traffic ELECTRICAL SPECIFICATIONS... -
Page 10: Physical Specifications
PHYSICAL SPECIFICATIONS Operating Temperature -34°C ~ +74°C Relative Humidity 0 - 95% non-condensing Power into Standalone 12VDC/24VAC External Dimensions 4.8”(122mm)L 4.3”(109mm)D 1.02”(26mm)H Weight of Equipment 7.5 oz (450g) INSTALLATION Open the package and inspect the unit, no sounds of loose items should be heard from inside. Power Connection Plug the 12VDC/24VAC power supply in source. - Page 11 After power and optical signal operate properly, connect video output from camera source into the video input port of the fiber optic transmitter using a BNC coaxial cable. Then connect a BNC coaxial cable between the output video port of receiver and a Digital Video Recorder, Matrix Switcher or Composite Video Monitor.
-
Page 12: About This Manual Standalone Receiver Video, Duplex Data
About this manual Before operating the unit, please read this manual thoroughly and retain it for future reference. The explanation given in this manual can be applied to the following models unless noted otherwise. DFC3301iRCZM2S: Digital 1 Video Receiver, duplex Data Transceiver, single fiber MM Standalone, 12VDC/24VAC ST DFC4301iRDZM2F: Digital 1 Video Receiver, duplex Data Transceiver, single fiber SM Standalone, 12VDC/24VAC FC... -
Page 13: Features
Features High speed synchronous digital transmission technology Modular construction design Highest optical dynamic range Power, Optical, Video, Data status indication Non-electromagnetic interference Transmission for extreme electromagnetic environment BNC video connector RJ45 data connector ST for MM and FC for SM optical connector Video DC Restoration Data interface: RS232 / RS422 / RS485 / Manchester / Biphase... -
Page 15: Attention
ATTENTION Do not exceed the range of power supply input 12VDC/24VAC. 8 dB for MM and 17 dB SM optical loss budget, the total loss in the optical fiber should be less than 8 dB for MM and 17 dB for MM, otherwise optical signal will not be present at the receiver. -
Page 16: Front Panel / Rear Panel View
Receiver DFC3301iRCZM2S & 4301iRDZM2F The Standalone Transceiver is a field installable, compact unit providing 1 channel Video receiver and duplex Data on 1 MM or SM fiber: The Front Panel The Rear Panel PORTS DEFINITION FRONT PANEL Video Output Port Optical Port ST &... -
Page 17: Data Rj-45 Configurations / Rs-232 Pinout Diagram
Data RJ45 Configuration as follows RS-232 (Pins only, no Dip Switch): PIN 2 RX PIN 3 TX PIN 4 GND RS-485 (2 Wire half duplex; Pins and Dip Switch): PIN 7 RX+/TX+ PIN 8 RX-/TX- and if at end of daisy chain RS-422 (Pins and Dip Switch): PIN 5 TX+ PIN 6 TX-... -
Page 18: Led Status Indicators
LED Status Indicators Power Indicator: ON to indicate the power applied, OFF to show that input voltage or the inner circuitry may be faulty Optical indicator: ON to indicate that the optical signal is transmitted Video indicator: ON to indicate video output Data indicator: ON to indicate data input/output traffic ELECTRICAL SPECIFICATIONS... -
Page 19: Physical Specifications
PHYSICAL SPECIFICATIONS Operating Temperature -34°C ~ +74°C Relative Humidity 0 - 95% non-condensing Power into Standalone 12VDC/24VAC External Dimensions 4.8”(122mm)L 4.3”(109mm)D 1.02”(26mm)H Weight of Equipment 7.5 oz (450g) INSTALLATION Open the package and inspect the unit, no sounds of loose items should be heard from inside. Power Connection Plug the 12VDC/24VAC power supply in source. - Page 20 After power and optical signal operate properly, connect video output from camera source into the video input port of the fiber optic transmitter using a BNC coaxial cable. Then connect a BNC coaxial cable between the output video port of receiver and a Digital Video Recorder, Matrix Switcher or Composite Video Monitor.
-
Page 21: About This Manual Card Receiver Video, Duplex Data
About this manual Before operating the unit, please read this manual thoroughly and retain it for future reference. The explanation given in this manual can be applied to the following models unless noted otherwise. DFC3301iRCZRS: Digital 1 Video Receiver, duplex Data Transceiver, single fiber MM Rack Card ST DFC4301iRDZRF: Digital 1 Video Receiver, duplex Data Transceiver, single fiber SM Rack Card FC... -
Page 22: Features
Features High speed synchronous digital transmission technology Modular construction design Highest optical dynamic range Power, Optical, Video, Data status indication Non-electromagnetic interference Transmission for extreme electromagnetic environment BNC video connector RJ45 data connector ST for MM and FC for SM optical connector Video DC Restoration Data interface: RS232 / RS422 / RS485 / Manchester / Biphase... -
Page 24: Attention
ATTENTION Do not exceed the range of power supply input 100-240VAC. 8 dB for MM and 17 dB SM optical loss budget, the total loss in the optical fiber should be less than 8 dB for MM and 17 dB for MM, otherwise optical signal will not be present at the receiver. -
Page 25: Front Panel / Rear Panel View
Receiver DFC3301iRCZRS, 4301iRDZRF, DFC3301idRCZRS & 4301idRDZRF Cards employs card guides to install in the 19” x 4U Subracks w/18 slots, models DFC9400-1 and 15 slots DFC9400-2 with dual power supplies. For Highest Racking Density capacity each card provides two independent Video receivers, duplex Data Transceivers: Each DFC3301idR Card has two Video output channels;... -
Page 26: Data Rj-45 Configurations / Rs-232 Pinout Diagram
Data RJ45 Configuration as follows RS-232 (Pins only, no Dip Switch): PIN 2 RX PIN 3 TX PIN 4 GND RS-485 (2 Wire half duplex; Pins and Dip Switch): PIN 7 RX+/TX+ PIN 8 RX-/TX- and if at end of daisy chain RS-422 (Pins and Dip Switch): PIN 5 TX+ PIN 6 TX-... -
Page 27: Led Status Indicators
LED Status Indicators Power Indicator: ON to indicate the power applied, OFF to show that input voltage or the inner circuitry may be faulty Optical indicator: ON to indicate that the optical signal is transmitted Video indicator: ON to indicate video output Data indicator: ON to indicate data input/output traffic ELECTRICAL SPECIFICATIONS... -
Page 28: Physical Specifications
PHYSICAL SPECIFICATIONS Operating Temperature -34°C ~ +74°C Relative Humidity 0 - 95% non-condensing Power into Card 5 VDC External Dimensions 6.8”(173mm)L 5.9”(150mm)D 0.8”(20.3mm)H Weight of Equipment 7.5 oz (450g) INSTALLATION Open the package and inspect the unit, no sounds of loose items should be heard from inside. -
Page 29: Applications
After power and optical signal operate properly, connect video output from camera source into the video input port of the fiber optic transmitter using a BNC coaxial cable. Then connect a BNC coaxial cable between the output video port of receiver and a Digital Video Recorder, Matrix Switcher or Composite Video Monitor.
Need help?
Do you have a question about the DFC3301iTCZM2S and is the answer not in the manual?
Questions and answers