5.2 Assembly of a mechanical cylinder 5.3 Disassembly of the mechanical cylinder 6 Scope of delivery 7 Assembly 7.1 Disassembly of the existing cylinder 7.2 Assembly of the CESeasy motor cylinder 8 Batteries 8.1 Required batteries 8.2 Battery consumption 8.3 Battery warnings...
Page 3
9.3 Configuration menu 10 Firmware update 10.1 Automatic firmware updates 10.2 Manual firmware updates 11 Administration 11.1 CESeasy web platform 11.2 Extension functions 12 Operation 12.1 How to use it with the rotary knob 12.2 Operation with a mechanical key 12.3 How to use it with a remote control...
These assembly and operating instructions, hereinafter referred to as the “manual”, will help you with the assembly and in a proper, safe, and beneficial use of the CESeasy products acquired. Anyone who assembles, administers, maintains, or disposes of CESeasy products, must have read and understood the complete contents of this manual.
CESeasy products have not been developed, tested and/or approved for access in life-threatening situations. Do not use CESeasy products on fire doors or panic doors. CESeasy products must be suitable for your door system. If you are in doubt, please contact the manufacturer of the door or lock to check suitability.
Store batteries in a cool and dry place. Direct heat may damage the batteries. Therefore, do not expose battery-operated devices to any strong heat source, and do not throw the bat- teries into fire. CESeasy motor cylinder Page 7 of 53...
Page 8
Remove leaking batteries immediately from the device. Clean the contacts before inserting new batteries. There is danger of injury from battery acid. Remove the empty batteries from the device. Please take note of the information on battery disposal (see "Disposal" on page 48). Page 8 of 53 CESeasy motor cylinder...
CESeasy web platform. 4.2 Scope of application The CESeasy motor cylinder is suitable for doors with a lock with euro profile cylinders below the handle set. CESeasy products have not been developed, tested and/or approved for access to escape and emergency routes.
5 Mechanical cylinder for the motor cylinder 5 Mechanical cylinder for the motor cylinder 5.1 Before ordering: Check cylinder length Before a CESeasy motor cylinder is ordered, the length of the mechanical cylinder has to be checked. Tools required: Folding rule or calliper gauge How to proceed: 1.
In order to offer break-in resistance, CESeasy motor units may only be combined with cylinders which have been pointed out as suitable by CES.
Page 12
3. Remove the assembly plate from the case of the motor unit. 4. Remove the black plastic bearing ring from the connecting sleeve. 5. Remove the driver pin (3 x 20 mm) from the connecting sleeve. Page 12 of 53 CESeasy motor cylinder...
Page 13
10. Press the driver pin through the hole in the shaft and hold on to it so that it cannot slip out of the hole. CESeasy motor cylinder Page 13 of 53...
Page 14
However, if the knob of the motor unit does turn with the cylinder, please contact the CES service. If the cylinder works correctly, you can mount the CESeasy motor cylinder to the door. Page 14 of 53...
2. Loosen and remove the four TORX screws which attach the assembly plate to the case. 3. Remove the cylinder with the assembly plate from the case of the motor unit. CESeasy motor cylinder Page 15 of 53...
Page 16
5. Loosen the four socket head screws on one side of the assembly plate and remove the cylinder from the assembly plate. 6. To mount the new cylinder, please proceed according to the assembly instructions from step 6. Page 16 of 53 CESeasy motor cylinder...
6 Scope of delivery 6 Scope of delivery 1 CESeasy motor cylinder (CESeasy motor unit with mounted mechanical cylinder) 1 Key 1 Cylinder fixing screw 1 Registration card (incl. extension function “Lock management, see "Extension functions" page 35) 1 Remote control (only part of the starter set)
Page 18
Keep your registration card in a safe place. You will need it in a service situation, or if you want to transfer the lock to another lock owner account. Page 18 of 53 CESeasy motor cylinder...
7 Assembly 7 Assembly It is recommended to have CESeasy products installed and configured by CES partners. They are not only familiar with the products, but rather also with your door. Therefore, they can guarantee that the devices work correctly.
7 Assembly 7.2 Assembly of the CESeasy motor cylinder Tools required Tool Required for Cylinder fixing screw Phillips screwdriver Smartphone with CESeasy app Configuration and test of the motor cylinder Smartphone prerequisites: iOS (iOS 9.2 or higher) or Android (Android 4.4 or higher)
Page 21
7 Assembly Assembly of the CESeasy motor cylinder 1. Remove all possibly existing batteries from the motor cylinder. 2. Fix the existing handle set tightly enough to insert the cylinder with ease in the door. This step is necessary because after having attached the motor cylinder, it will no longer be possible to fasten the handle set.
Page 22
"Configuration" page 27). 10. Check that the motor cylinder works correctly with the CESeasy app with the open door . 11. Check that the motor cylinder works correctly with the CESeasy app with the closed door. Now the motor cylinder is ready.
Battery warning in the CESeasy app If the batteries are nearly empty, a pop-up window opens in the CESeasy app after an opening or closing operation which informs you about the battery status. CESeasy motor cylinder...
Allen key (4mm). If you want to prevent that the battery compartment can be manually opened, you can replace the design screw by a safety screw (M4 thread, length 8mm). Page 24 of 53 CESeasy motor cylinder...
Page 25
3. If necessary, take out the six empty batteries. 4. Insert the six new batteries. Please ensure that the batteries are inserted according to the labelling in the battery compartment which indicates the correct polarity. CESeasy motor cylinder Page 25 of 53...
8 Batteries 5. Slide the cover back onto the battery compartment. 6. Tighten the design screw by hand. The batteries are now inserted or have been changed. 8.5 Battery disposal "Disposal" on page 48. Page 26 of 53 CESeasy motor cylinder...
To enable the CESeasy app to connect to the lock, the location transmission must be activated. This applies to both the settings of the app itself (CESeasy app must be allowed to share the location) and the location transmission of your smartphone (location transmission must be activated for the smartphone).
If you use an iPhone: iPhone 4S or newer models Bluetooth 4.0 or higher suitable for Bluetooth Low Energy How to couple the motor cylinder with the CESeasy app 1. Loosen the design screw. 2. Slide the cover of the battery compartment downwards and remove it.
Page 29
The motor cylinder has to be within the range of the smartphone. 4. Open the CESeasy app on your smartphone. 5. Make sure you are in the “Locks” menu of the app. Click on the “Scan” button in the upper right corner.
Page 30
Otherwise, your configuration will be overwritten by the first firmware update. No subsequent firmware updates will overwrite your configuration. 7. If you click on “Update”, a firmware update is carried out (see "Firmware update" on page 34). Page 30 of 53 CESeasy motor cylinder...
CESeasy app. To be able to open a door which is in night locking mode, you must have a remote control or the CESeasy app. In an emergency, this could lead to life-threatening situations! Before you activate the night locking mode, be sure to note all requirements concerning escape routes and fire protection (e.g.
Page 32
Determines how long the motor has to turn to pull back the latchbolt at daytime. Open Reversing time Determines how long the motor has to turn to release the lock after having reached the Close end stop in closing direction. Page 32 of 53 CESeasy motor cylinder...
Page 33
10 locks will see a long, confusing list of locks in the CESeasy app. If you reduce the transmission power of the locks, the list of locks in the immediate vicinity will be reduced.
The first firmware update after installation should be carried out manually. However, if this has not happened, the firmware update is carried out automatically after the device has been operated by the CESeasy App. In this case, the CESeasy app shows a message, and the firmware update will be completed after approx. 45 seconds.
11 Administration 11 Administration 11.1 CESeasy web platform The device is managed on the CESeasy web platform. There you can issue keys, add remote controls, etc. For details, please refer to the manual for the CESeasy web platform. 11.2 Extension functions Several extension functions are available at CES.
Page 36
Your account is extended with the tab “Buildings" which allows you to create buildings and to add locks to these buildings. If you own the “Building management” function, you can additionally define how the name of the lock is displayed on the web platform and in the CESeasy app.
Page 37
If you already own an organisation account, this function allows you to add another organ- isation with 100 employees. One organisation has a validity of 5 years. To extend its validity by another 5 years, you have to add the function "100 employees" to this organisation. CESeasy motor cylinder Page 37 of 53...
CESeasy app. To be able to open a door which is in night locking mode, you must have a remote control or the CESeasy app. In an emergency, this could lead to life- threatening situations! Before you activate the night locking mode, be sure to note all requirements concerning escape routes and fire protection (e.g.
12.4 Operation via smartphone You can operate the motor cylinder by means of the CESeasy app and a suitable smartphone. To operate the motor cylinder, you need a digital key. You can assign digital keys to yourself or others on the CESeasy web platform.
Page 40
To enable the CESeasy app to connect to the lock, the location transmission must be activated. This applies to both the settings of the app itself (CESeasy app must be allowed to share the location) and the location transmission of your smartphone (location transmission must be activated for the smartphone).
Input for an optional door contact (347129V). A special cable is required (347110V). Set containing a door contact and a cable: 347128V Max. cable length: 30 cm Further inputs and outputs Available via the CESeasy communication module RF-Transceiver RF-Transceiver 868 MHz, for remote controls and the communication module Bluetooth LE transceiver 2.4 GHz, to communicate with mobile phones...
Connecting cable 347110V Set containing a door contact and a connecting cable 347128V 14.1.1 How to install a door contact How to install a door contact 1. Loosen the design screw by hand. CESeasy motor cylinder Page 43 of 53...
Page 44
4. Remove the lug in the cover of the battery compartment. 5. Run the connecting cable through the recess into the motor cylinder (see picture). 6. Slide the cover back onto the battery compartment. Page 44 of 53 CESeasy motor cylinder...
Page 45
The door contact cable must not exceed approx. 25cm. A cable which is too long may lead to unintended behaviour. 10. In the configuration menu, activate the use of the door contact (see "Configuration" on page 27). CESeasy motor cylinder Page 45 of 53...
2. Slide the cover of the battery compartment downwards and remove it. 3. Cut the wire ends to 6mm length. Make sure that the wire ends are either tin-plated or carry suitable wire end sleeves. Page 46 of 53 CESeasy motor cylinder...
Page 47
(removed lug). Now the external power supply unit is connected. It is recommended to additionally insert batteries which ensure that the motor cylinder can also be used in the event of a power outage. CESeasy motor cylinder Page 47 of 53...
Used batteries may contain contaminants or heavy metals which can pose a health and environmental hazard. Batteries are recycled, as they contain important raw materials like iron, zinc, manganese, or nickel. Page 48 of 53 CESeasy motor cylinder...
Page 49
Packaging of the components is made from environmentally friendly, reusable materials. In detail, these are: Outside packaging and inlays from cardboard Inlays and protective foils from Polyethylene (PE) Please dispose of the packaging in an environmentally friendly way through waste separation streams. CESeasy motor cylinder Page 49 of 53...