Table of Contents
Advertisement
Quick Links
Part # SC-20-840-SV-OS-BZ
SC-20-840-SV-OS-W
Model # 51402241
51402242
USe and Care GUide
Led SeCUriTY LiGHT
dUSk TO daWn
Questions, problems, missing parts?
Call ETiSSL Customer Service
8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETi-SSLI (1-855-384-7754)
www.ETiSSL.com
THANK YOU
We appreciate the trust and confidence you have placed in ETi through the purchase of this LED light.
Visit us online to see our full line of products. Thank you for choosing ETi!
Advertisement
Table of Contents
Summary of Contents for ETI SC-20-840-SV-OS-BZ
- Page 1 8 a.m. - 5 p.m., CST, Monday - Friday 1-855-ETi-SSLI (1-855-384-7754) www.ETiSSL.com THANK YOU We appreciate the trust and confidence you have placed in ETi through the purchase of this LED light. Visit us online to see our full line of products. Thank you for choosing ETi!
-
Page 3: Table Of Contents
Table of Contents Hardware Included .........4 Table of Contents ........3 Installation ..........5 Safety Information ........3 Maintenance ..........7 Warranty ...........3 Light Distribution ........7 Pre-Installation .........4 PIR Sensor Testing ........8 Planning Installation ......4 Care & Cleaning ........11 Tools Required ........4 Troubleshooting ........11 Package Contents ........4 Safety information nOTiCe: This equipment has been tested and found to comply with... -
Page 4: Pre-Installation
Pre-installation PLANNING INSTALLATION Before beginning assembly, installation, or operation of the product, make sure all parts are present. Compare parts with package contents list and hardware contents list above. If any part is missing or damaged, do not attempt to assemble, install, or operate the product. -
Page 5: Installation
installation WarninG: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker before removing the existing light fixture or installing the new one. With power disconnected to the electrical box, remove the existing fixture. - Page 6 installation (continued) Attaching the light fixture to the mounting bracket □ Install the light fixture base (B) to the mounting bracket (FF) using the long mounting screw (AA) provided, making sure no wires are visible outside the light fixture. □ Insert the rubber plug (DD) into the hole on the light fixture base (B) for a finished appearance.
-
Page 7: Maintenance
Maintenance To replace the photocell □ Remove the rubber plug (DD) and long mounting screw (AA) from the light fixture base (B). □ Unscrew the two wire connectors (EE) to disconnect the photocell (C). □ Replace with a new photocell (Model # EP-120R or equivalent) using the same two wire connectors (EE). Light distribution C0 / 180, 78.7 C30 / 210, 78.2... -
Page 8: Pir Sensor Testing
Pir Sensor Testing Lighting the product and preheat □ When power is first applied, the light will turn on immediately. Waiting for 20 seconds to allow the sensor to warm up. Test Mode □ The motion sensor must be tested before setting the time and sensitivity levels. - Page 9 Pir Sensor Testing (continued) 1. Auto Mode Set-up □ Once the fixture has been tested for proper operation and sensitivity, rotate the TIMER control knob past the “TEST” setting into the timer settings. The timer There is LED settings indicate how long the light stays on after the indicator inside PIR senses motion.
- Page 10 Pir Sensor Testing (continued) Troubleshooting □ Extremely hot or cold weather could affect the performance of the built-in sensor that detect body heat. Certain winter clothing can shield a person’s body heat from the sensor during extremely cold weather. During extremely hot weather, the sensor may not be able to distinguish the difference between normal body temperature and the surrounding high temperature.
-
Page 11: Care & Cleaning
Care & Cleaning CaUTiOn: Before attempting to clean the fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box. □ Clean the fixture with a soft, dry cloth. □ Do not use cleaners with chemicals, solvents, or harsh abrasives. Troubleshooting WarninG: Before doing any work on the fixture, disconnect power to the light fixture. - Page 12 Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday 1-855-ETI-SSLI (1-855-384-7754) www.eTiSSL.com Retain this manual for future use.
Need help?
Do you have a question about the SC-20-840-SV-OS-BZ and is the answer not in the manual?
Questions and answers