ML350G-10 Industrial Computer 1 - About Logic Supply Logic Supply is powering innovation with highly configurable embedded and IoT computers engineered for re- liability. Businesses worldwide depend on our solutions to operate in the toughest environments while tapping into the evolving Industrial Internet of Things. This guide will introduce you to the ML350G-10 industrial fanless computer and the system specifications. For technical questions or support, please reach out via our contact information below. You have a lot of choices when choosing computer hardware. The Logic Supply Team wants to thank you for trusting our components to meet your application needs. The ML350G-10 is the result of input from partners like you. We’ve worked hard to create a system that meets the varied needs of industrial and IoT computing...
Information in this document is subject to change without notice. Legal Disclaimer: Specifications and information contained in this manual are furnished for information- al use only and subject to change without notice, and should not be constructed as a commitment by Logic Supply. Logic Supply assumes no responsibility for any errors or omissions that may appear in this manual.
ML350G-10 Industrial Computer 3 - Safe Use and Installation Instructions 1. Do not open or modify the device. The device has been tested and complies with FCC and CE regulations. Modification of the device will void these certifications. Install the device securely. Be careful handling the device to prevent injury and do not drop. Wall or ceiling mounting device requires use of a mounting plate or pair of mounting brackets. Plate or brackets must be of metal construction and have a minimum thickness of 1mm. Use M3x0.5mm Flat Head screws to attach mounting plate or mounting brackets to threaded holes on bottom of chassis. Screws should be minimum length of 4mm. Ad 1mm of screw length for every mm of additional thickness of plate or bracket beyond 1.5mm. Operational temperature must be between 0-40°C with a noncondensing relative humidity of 10-90%.
ML350G-10 Industrial Computer 4 - What’s In The Box ML350 Built & Tested System If you purchased additional items such as specific mounting brackets, power supplies or antennas, they will be located in the system box or within the outer shipping carton. All drivers and product guides can be found on the corresponding product page at www.logicsupply.com.
ML350G-10 Industrial Computer 5 - System Overview 5.1 - System Diagram Power Button USB C USB 3.0 Audio (Optional) In/Out Antenna Power In Gb LAN Gb LAN USB 2.0 Antenna (Optional) (Optional) (Optional) DisplayPort...
ML350G-10 Industrial Computer 5.2 - System Specifications N3350 N4200 Processor and Chipset Intel Apollo Lake with integrated graphics Memory 1 x 204-pin DDR3L SO-DIMM up to 8GB Audio Controller Realtek ALC283 audio codec Full-size/half-size mPCIe with PCIe, SATA, and USB signal Expansion Full-size mPCIe with PCIe and USB signal Full-size mPCIe with SATA and USB signal DisplayPort, Version 1.2 (HDMI CEC option, supports dual mode and MST) Rear I/O GbE LAN USB2.0 USB3.0 USB type C 3.1 Front I/O Audio jack; line-in/out...
ML350G-10 Industrial Computer 5.4 - Mounting Guide Wall Mounting Step 1: Attach wall mount brackets to chassis Step 2: Mark and prep holes in surface for mounting Step 3: Fasten system to surface VESA Mounting Step 1: Install 4 VESA Screws into your display/surface Step 2: Attach VESA bracket to the chassis Step 3: Hang combined system and bracket to display/surface DIN Rail Mounting Step 1: Attach wall mounting brackets to the chassis Step 2: Attach DIN Rail Clips to the mounting brackets Step 3: Clip system to the DIN Rail...
ML350G-10 Industrial Computer 6 - Motherboard Overview Audio USB 3.0 USB C Power Button In/Out DisplayPort 1 DisplayPort 2 LAN 2 LAN 1 Power In USB 2.0 (Optional) mPCIe/mSATA mSATA mPCIe Power In Header CEC Header Battery Header AT/ATX Jumper Memory Slot COM Header...
ML350G-10 Industrial Computer 6.1 - Jumpers and Headers Guide Number Location Function J1_BIOS BIOS Load Default Header/Clear CMOS LAN 1 Connector LAN 2 Connector DisplayPort 1 DisplayPort 2 USB Type C Connector USB 3.0 Connector Audio Connector J9_CEC CEC Header USB 2.0 Connector USB 2.0 Connector J12_USB USB 2.0 Header...
ML350G-10 Industrial Computer 6.2 - Configuring Jumpers Refer to the following diagrams for configuring jumpers and onboard headers. J1_BIOS The J1_BIOS jumper loads the default BIOS settings. Short pins 2-3 for normal operation. Short pins 1-2 to clear the CMOS and reset the system setup configuration to default settings. If you experience challenges powering up, short pins 1-2 to troubleshoot. Clear CMOS Normal J13_AT_ATX AT = Auto power on. ATX = No auto power on. AT Mode ATX Mode...
ML350G-10 Industrial Computer 6.3 - Onboard Headers An onboard header is a connection on the motherboard that permits connecting a peripheral component to an external port on the system J9_CEC The ML350G-31 can be configured with a module that allows for CEC functionality. The J9_CEC connector includes wiring connections for the HDMI Consumer Electronics Control (CEC). COM1 and COM2 The motherboard includes the following COM ports: COM1: I/O port 0x3F8, IRQ 4 COM2: I/O port 0x2F8, IRQ 3 RS232...
ML350G-10 Industrial Computer J23_Ambient Header The J23_AMBIENT connector provides System Management Bus (SM Bus) communication. SMBus Clock SMBus Data J12_USB The J12_USB connector supports two USB ports. 5V_USB 5V_USB Data (Negative) Data (Negative) Data (Positive) Data (Positive) None XBT1_BATTERY and XBT2_BATTERY Connect the system and backup batteries to the XBT1_BATTERY and XBT2_BATTERY connectors.