Nippon Antenna AU8F Instruction Manual

How to connect to electricity supply
Preparation of the water resistant cap:
Clip off the end of water resistant cap
according to the diameter of the coaxial
cable.
Preparations of coxial cable (5CFB)
F-type connector is sold separately
Tools needed
cutter, knife, scissor or nipper, plier
aluminum ring
Parts name
wire mesh
conductor
outer coat cover aluminum F type
insulator
foil
connector
Waterproof cap should be pierced
with coaxial cable in advance.
cable
water resistant
insulator
Remove the insulator portion (14mm) cap
as shown in the dotted line of the
coaxial cale (cut about 1mm)
aluminum ring
Peel off the outer cover and pierce
the aluminum ring
Cut the shield wire mesh of the
cable insulator
Turn over the wire mesh
Remove the insulator about 3mm
in length

Specifications

Models
13~69 13~69
Receiving channels
Number of elements
Operating gain
Impedance
VSWR [Less than]
Half bandwidth
Front / Rear Ratio
Wind endurance
[mm]
Dimensions L x W X H
Mass (Weight)
Suitable mast diameter
For improvement and/or change of the product, the information presented in this manual is subject to change without notice.
NIPPON ANTENNA
NIPPON ANTENNA Co Ltd.
No. 49-8 Nishiogu 7-Chome, Arakawaku, Tokyo, 116-8561, Japan
Tel. (03) 3893-5221 / Fax (03) 3800-1931
www.nippon-atenna.co.jp
KARMOND Company (North America Distributor)
1800 Sheppard Avenue East, Suite 55160
Toronto, Ontario, Canada M2J 5B9
Tel. (416) 816-9848 / dtvant@karmond.com / www.karmond.com
Insert the F-Type connector between the shield
wire mesh and the insulator. Tighten the aluminum
ring by squeezing it with pliers as shown in the picture.
Cut the center conductor at about 1~2 mm from the edge of
the F-Type conector.
Longer conductor may damage the contact terminal.
Cutting the center conductor diagonally will make it
Note
easier to connect the cable.
Conneting coaxial cable to the antenna and water proofing
Connect the coaxial cable to the antenna feeder assembly and tighten the connector
with pliers, etc. Do not over tighten the connector. The torque should be about 2.0 N.m
(20 kgf-cm). Complete with the water resistant cap tightly inserted towards the feeder
assembly. It is recommended that additional protection to wrap self adhesive tape around
the connnector then cover with the water resistant cap for regions that might have salt
damages and (or) heavy rain.
Antenna feeder
assembly
power supply
Electric tape
(not included)
water resistant
cap
Vinyl tape
(not included)
13~69 13~69 13~69 13~69
NIPPON ANTENNA
INSTRUCTION MANUAL
F-type
connector
Thank you for purchasing Nippon Antenna products.
Please read this manual carefully before using.
Keep this manual in a safe place for future
reference.
JEITA marks mean the products (a satellite receiver, a
terrestrial digital broadcast TV receiver, the antenna,
etc.) have been tested and meet applicable standards
for safety and/or performance, including the applicable
standards written or administered by the Japan Electronics and
Information Technology Industries Association (JEITA).
13~69
AU14AF
90 DAY LIMITED WARRANTY
Nippon Antenna Company warrants this product against any defects in materials or workmanship wthin 90 days from date of purchase. No warranty claim will be
honored unless at the time the claim is made; you present proof of purchase to an authorized Nippon Antenna Company dealer (If unknown, please contact
Nippon Antenna Distributor Karmond Company in Canada). Nippon Antenna Company will either repair or replace the defective product at no charge to you.
This warranty covers parts, but does not cover any costs incurred in removal, shipping or reinstallation of the product. This limited warranty does not apply if the
product is damaged, deteriorated, malfunctions or fails from: misuse, improper installion, abuse, neglect, accident, tampering, modification of the product as
originally manufactured by Nippon Antenna Company, usage not in accordance with product instructions or acts of nature such as damage caused by wind,
lightning, ice or corrosive environments such as salt spray and acid rain. The 90-Day Warranty is provided on the condition that the equipment is properly delivered
with all handling and freight charges prepaid to your Nippon Antenna dealer for return to our distributor for repair or replacement. Nippon Antenna Company dealers
will arrange for the replacement or reapir and return to you without charge the product that failed due to defective material or workmanship.
NIPPON ANTENNA COMPANY WILL NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE BY ANY
OTHER PERSON.
ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARANTIES OF FITNESS FOR A PARTICULAR PURPOSE
AND MERCHANTABILITY ARE LIMITED TO THE 90-DAY PERIOD OF THIS WARRANTY.
The foregoing shall be the sole and exclusive remedy of any person, whether in contract, tort or otherwise, and Nippon Antenna Company shall not be liable for
incidental or consequential damage or commercial loss, or from any other loss or damage except as set forth above.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights, which vary from state to state and Canada.
Karmond Company (North America Distributor) www.karmond.com
Nippon Antenna Company
Cautions and
Safety Notice
Home Use UHF
Outdoor Antenna
Features
Terrestrial Digital TV Antenna
Obtained the maximum front/rear ration, gain, and VSWR
for the wide frequency range employing the dual dipole
array feeding system.
Employing the corner reflector to reduce the ghost
interference with improved front/rear ratio. (except AU8F)
Aluminum arm stand is used for anti-corrosion and better
durability.
Stainless antenna probe is used for better durability.
AU14AF
Receiving Channels : 13ch ~ 69ch 14 pieces of antenna probe for horizontal and vertical waves
Make sure to consult with specialist for the installation of antenna at roof top,
and to secure it safely.