Galaxy Audio RM-RDSTNR Quick Start Manual

GAL A X Y AUDIO
AM / FM RDS Tuner
Included Components
1.
AM/FM RDS Tuner x1
2.
AM Antenna Set x1
3.
FM Antenna Wire x1
4.
Dual RCA Cable x1
5. AC Power Cord x1
6. Remote Control x1
7.
Quick Start Guide x1
Setup
1
Connect Power Cable to the
RM-RDSTNR. Connect the other end to
a power outlet. (Optional DC 13.2 Power
Cable may also be used)
Operation
1
To Select FM 1, FM 2 or AM frequencies,
Press "BAND".
6
To listen to a saved CH, press
"MEMORY UP" or "M1~M5". To select
higher, use "+5" and "M1~M5".
Ex: "+5" and "M3" = CH8.
1.
2. 3.
4.
2
OR
Attach the AM and/or FM Antenna on
the RM-RDSTNR.
2
OR
Press "TUNING " or "TUNING "
to select channel.
7
To choose Mono or Stereo mode, Press
"MO / ST".
5.
7.
GAL A X Y AUDIO GAL A X Y AUDIO
AM / FM RDS Tuner AM / FM RDS Tuner
Included Components
1. AM/FM RDS Tuner x1
2. AM Antenna Set x1
3. FM Antenna Wire x1
4. Dual RCA Cable x1
5. AC Power Cord x1
6. Remote Control x1
7. Quick Start Guide x1
Setup
1
Connect Power Cable to the
RM-RDSTNR. Connect the other end to
Cable may also be used) a power outlet. (Optional DC 13.2 Power
Operation
1
To Select FM 1, FM 2 or AM frequencies,
Press "BAND".
6
"MEMORY UP" or "M1~M5". To select To listen to a saved CH, press
higher, use "+5" and "M1~M5".
Ex: "+5" and "M3" = CH8.
6.
3
Make sure the volume is reduced until
ready for sound. Connect RCA Cable to
the Left and Right RCA Outputs and
connect to Amplifier, Mixer, or Receiver.
3
OR
To start auto scan search, hold TUNING
for over 2 seconds.
8
To search and go to a travel/traffic
station (if available in area), press TA.
Quick Start Guide Quick Start Guide
RM-RDSTNR RM-RDSTNR
What May be Needed to Rack
1. 5. 7.
(Not Included)
1.
1. Rack Screws 10/32 x .75",
2. 3. Phillips Truss Head Screws
6.
2. 2.
#2 Phillips Head Screwdriver
4.
Racking/Mounting (Optional)
2 3 3 4 5
OR
Attach the AM and/or FM Antenna on Make sure the volume is reduced until Power on the RM-RDSTNR Tuner. Align RDS Tuner up evenly. Turn the
the RM-RDSTNR. ready for sound. Connect RCA Cable to screw but leave room to adjust. Once
connect to Amplifier, Mixer, or Receiver. the Left and Right RCA Outputs and securely. all four screws are in place, tighten
1. Rack Screws 10/32 x .75",
2 3 4 5
OR OR
Press "TUNING " or "TUNING " To start auto scan search, hold TUNING To set a memory CH, press "MEMORY" To set above 5, press Memory , then
to select channel. for over 2 seconds. then press "1~5", then Memory again. "+5", then "1~5" and press Memory
(10 memory assignable per freq. band) again. Ex: "+5" and "3" to set it at CH8. Phillips Truss Head Screws
7 8 9 10
"MO / ST". To c hoos Mono or Stereo mode e , Press To search and go to a travel/traffic station (if available in area), press TA. on the Remote. (Every press adds To use Sleep function, press "SLEEP" the LCD shows "00". To cancel Sleep, press "SLEEP" until
10 min, with 90 min being max.)
2. #2 Phillips Head Screwdriver
4
Power on the RM-RDSTNR Tuner.
4
To set a memory CH, press "MEMORY"
then press "1~5", then Memory again.
(10 memory assignable per freq. band)
9
To use Sleep function, press "SLEEP"
on the Remote. (Every press adds
10 min, with 90 min being max.)
Quick Start Guide
RM-RDSTNR
What May be Needed to Rack
(Not Included)
1.
2.
Racking/Mounting
(Optional)
5
Align RDS Tuner up evenly. Turn the
screw but leave room to adjust. Once
all four screws are in place, tighten
securely.
5
To set above 5, press Memory , then
"+5", then "1~5" and press Memory
again. Ex: "+5" and "3" to set it at CH8.
10
To cancel Sleep, press "SLEEP" until
the LCD shows "00".