Wasp WWS750-BS Quick Reference Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Wasp WWS750-BS

Base Station

Quick Reference Guide

Table of Contents

Need help?

Do you have a question about the WWS750-BS and is the answer not in the manual?

Questions and answers

Summary of Contents for Wasp WWS750-BS

Page 1 Wasp WWS750-BS Base Station Quick Reference Guide...
Page 2 An Unpublished Work - All rights reserved. No part of the contents of this doc- umentation or the procedures described therein may be reproduced or trans- mitted in any form or by any means without prior written permission of Wasp Barcode Technologies or its subsidiaries or affiliates ("Wasp Technologies"...
Page 3: Table Of Contents
Table of Contents Using the WWS750-BS Base Station ............1 Installation ....................... 2 Regulating the Cradle Position .............. 2 Mounting with the Metal Plate ............. 4 System Connections ..................5 Connecting and Disconnecting the Interface Cable ......5 WWS750-BS Configuration ................7 Serial Configuration ................
Page 5: Using The Wws750-Bs Base Station
Using the WWS750-BS Base Station The WWS750-BS Presentation Base, when paired with one or more WWS750 reader, builds a Cordless Reading System for the collection, decod- ing and transmission of bar code data. It can be connected to a Host PC via RS-232, USB, or KBD Wedge, and is suited for single-cradle layouts.
Page 6: Installation
Installation Installation To set up your WWS750-BS cradle you must: Physically install the cradle. Make all system connections. Configure the WWS750-BS cradle. The cradle package contains the following items: • WWS750-BS Presentation Base • Hex Key • WWS750-BS Quick Reference Guide •...
Page 7 Installation The rubber spacers included in the box can be used to fix the position of the cradle: Quick Reference Guide...
Page 8: Mounting With The Metal Plate
Figure 1 on page Slide the tabs on the back of the cradle onto the metal plate as shown in Figure After aligning the tabs, push up to lock into place. Figure 1. Mounting Plate on Wall WWS750-BS Base Station...
Page 9: System Connections
Multi-Interface Connector Connecting and Disconnecting the Interface Cable The WWS750-BS can be connected to a Host by means of a multi-interface cable, which must be simply plugged into the Host connector, visible on the front panel of the cradle. To disconnect the cable, insert a paper clip or other similar object into the hole corresponding to the Host connector on the body of the cradle.
Page 10 The power supply is required only if you need to connect the interface cable to a standard USB Port. The power supply is not required if you connect the interface cable to a PoweredUSB 12V or 24V port. NOTE WWS750-BS Base Station...
Page 11: Wws750-Bs Configuration
Host PC via the RS-232 or USB-COM interface or by reading configuration bar codes with the WWS750. Serial Configuration By connecting the WWS750-BS to a PC through an RS-232 or USB-COM inter- face cable it is possible to send configuration strings from the PC to WWS750-BS.
Page 12: Selecting The Interface Type
5 seconds. The scanner will change to a state that allows programming with bar codes. RS-232 RS-232 standard interface Select RS232-STD RS-232 Wincor-Nixdorf Select RS232-WN RS-232 for use with OPOS/UPOS/JavaPOS Select RS-232 OPOS WWS750-BS Base Station...
Page 13 Selecting the Interface Type USB COM to simulate RS-232 standard interface USB-COM-STD USB-OEM (can be used for OPOS/UPOS/JavaPOS) USB-OEM USB Keyboard with standard key encoding Select USB Keyboard USB Keyboard with alternate key encoding USB Alternate Keyboard USB Keyboard for Apple computers USB-KBD-APPLE a.
Page 14: Keyboard Interface
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Alternate Key Select KBD-AT-ALT Keyboard Wedge for IBM AT PS2 with alternate key encoding but without external keyboard Select KBD-AT-ALT-NK PC/XT w/Standard Key Encoding Select KBD-XT WWS750-BS Base Station...
Page 15: Scancode Tables
Selecting the Interface Type KEYBOARD (continued) Keyboard Wedge for IBM Terminal 3153 Select KBD-IBM-3153 Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make only keyboard Select KBD-IBM-M Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make break keyboard Select KBD-IBM-MB Keyboard Wedge for DIGITAL Terminals VT2xx, VT3xx, VT4xx...
Page 16: Country Mode
All other interfaces support ONLY the following Country Modes: U.S., Belgium, Britain, France, Germany, Italy, Spain, Sweden. COUNTRY MODE ENTER/EXIT PROGRAMMING MODE Country Mode = U.S. Country Mode = Belgium Country Mode = Britain *Supports only the interfaces listed in the Country Mode feature description WWS750-BS Base Station...
Page 17 Selecting the Interface Type COUNTRY MODE (continued) Country Mode = Croatia* Country Mode = Czech Republic* Country Mode = Denmark* Country Mode = France $CKBCO13(CR) Country Mode = French Canadian Country Mode = Germany *Supports only the interfaces listed in the Country Mode feature description Quick Reference Guide...
Page 18 Country Mode = Italy Country Mode = Japanese 106-key* $CKBCO14(CR) Country Mode = Lithuanian Country Mode = Norway* Country Mode = Poland* Country Mode = Portugal* *Supports only the interfaces listed in the Country Mode feature description WWS750-BS Base Station...
Page 19 Selecting the Interface Type COUNTRY MODE (continued) Country Mode = Romania* Country Mode = Spain Country Mode = Sweden Country Mode = Slovakia* Country Mode = Switzerland* *Supports only the interfaces listed in the Country Mode feature description Quick Reference Guide...
Page 20: Caps Lock State
This applies to keyboard wedge interfaces. This does not apply when an alter- nate key encoding keyboard is selected. ENTER/EXIT PROGRAMMING MODE Caps Lock State = Caps Lock OFF Caps Lock State = Caps Lock ON Caps Lock State = AUTO Caps Lock Enable WWS750-BS Base Station...
Page 21: Numlock
Selecting the Interface Type Numlock This option specifies the setting of the Numbers Lock (Numlock) key while in keyboard wedge interface. This only applies to alternate key encoding inter- faces. It does not apply to USB keyboard. ENTER/EXIT PROGRAMMING MODE Numlock = Numlock key unchanged Numlock = Numlock key toggled Quick Reference Guide...
Page 22: Technical Features
-20° to +50 C / -4 to +122 °F Radio Battery Charging 0° to +40 °C / +32° to +104 °F -20° to +70 C / -4 to +158 °F Storage Temperature Humidity 90% non condensing Protection Class IP40 WWS750-BS Base Station...
Page 23 Width 98mm SYSTEM CONFIGURATION Max number of devices per base station * Having a switching regulator inside, the WWS750-BS draws the same power, regardless of the supply voltage. i.e. as the input voltage increases the current drawn decreases Quick Reference Guide...
Page 24: Wasp Technologies Limited Factory Warranty
Wasp service center, with shipping charges pre- paid. Wasp shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Wasp service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
Page 25: Ergonomic Recommendations
POSSIBILITY OF SUCH DAMAGES. Risk of Loss Customer shall bear risk of loss or damage for product in transit to Wasp. Wasp shall assume risk of loss or damage for product in Wasp’s possession. In the absence of specific written instructions for the return of product to Customer, Wasp will select the carrier, but Wasp shall not thereby assume any liability in connection with the return shipment.
Page 26 Services and Support NOTES WWS750-BS Base Station...
Page 28 ©2018 Wasp and its Group companies - All right reserved. Wasp Technologies and the Wasp Technologies logo are registered trademarks of Wasp Barcode Technologies in many countries, including the U.S.A. and the E.U. Wasp Barcode Technologies 1400 10th Street Plano, Texas...