1. Manuals
  2. Brands
  3. Focal Point Manuals
  4. Hob
  5. HB0420X4
  6. Use, installation and maintenance instructions

Focal Point HB0420X4 Use, Installation And Maintenance Instructions

Built-in gas hobs
Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTIONS MANUAL AND HINTS FOR
THE USE, INSTALLATION AND MAINTENANCE
FOR BUILT-IN GAS HOBS
The appliance was designed and made in accordance with the European standards listed below:
⇒ EN 30-1-1, EN 30-2-1 and EN 437 plus subsequent amendments (Gas Standards).
⇒ EN 60 335-1 and EN 60 335-2-6 plus relative amendments (Electrical Standards).
The appliance complies with the prescriptions of the European Directives as below:
⇒ 73/23/EEC + 93/68/EEC concerning electrical safety (LVD).
⇒ 89/336/EEC + 92/31/EEC + 93/68/EEC concerning electromagnetic compatibility (EMC).
⇒ 90/396/EEC + 93/68/EEC concerning gas safety (GAD).
"These instructions are only valid if the country symbol appears on the Instruction Manual and on the appliance"
Page 1 of 10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HB0420X4 and is the answer not in the manual?

Questions and answers

Summary of Contents for Focal Point HB0420X4

  • Page 1 INSTRUCTIONS MANUAL AND HINTS FOR THE USE, INSTALLATION AND MAINTENANCE FOR BUILT-IN GAS HOBS The appliance was designed and made in accordance with the European standards listed below: ⇒ EN 30-1-1, EN 30-2-1 and EN 437 plus subsequent amendments (Gas Standards). ⇒...

  • Page 2: Table Of Contents

    TECHNICAL ASSISTANCE AND SPARE PARTS Before this appliance left the factory it was tested and set (see the specific adjustment sticker data plate, put on the bottom of the appliance, to check gas adjustment) by specialized, expert personnel to guarantee the best functioning results. Attention: Qualified personnel must do any subsequent repairs or adjustments that may be necessary with the maximum care and attention.

  • Page 3: Important Notes And Precautions For Use

    1. IMPORTANT NOTES AND PRECAUTIONS FOR USE You have purchased one of our products for which we thank you. We are confident that this new appliance, modern, functional and practical, made with top quality materials, will meet all your demands. This new appliance is easy to use but before installing and using it, it is important to read this Instruction Manual through carefully.

  • Page 4: Description Of The Appliance

    2. DESCRIPTION OF THE APPLIANCE 1. Rapid gas burner (R) of 3,00 kW 2. Semi-Rapid gas burner (SR) of 1,75 kW 3. Auxiliary gas burner (Aux) of 1,00 kW 4. Ultra-Rapid triple crown (UR-3c) of 3,50 kW 5. Gas burner control knob 6.

  • Page 5: Gas Burners

    GAS BURNERS Manual ignition Press and turn anclockwise the knob corresponding to the burner you wish to use from “Off” position (full disk symbol on control panel), until it reaches the “Maximum” position (fig. 1) corresponding to the big flame and place a lighted match close to the burner.

  • Page 6: Instructions For The User: Cleaning And Maintenance

    4. INSTRUCTIONS FOR THE USER: CLEANING AND MAINTENANCE Prior to any maintenance work or cleaning, disconnect the appliance from the electricity mains. The surface of the hob, pan supports, enamelled burner caps (C) and burner heads (T) (see fig. 5) need to be cleaned after each time they are used with warm soapy water, rinsed and then dried well to keep them in good condition.
  • Page 7 (*) Air inlet - minimum section 100 cm UNPACKING THE APPLIANCE Once the outer wrapping and the inner wrappings of the various parts have been removed, check and make sure that the appliance is in perfect condition. If you have any doubts do not use the appliance and call your nearest Assistance Centre. Some parts are mounted on the appliance and protected by a plastic film.

  • Page 8: Gas Connection

    GAS CONNECTION Before to connect the appliance to the gas network, check that the adjustment sticker data plate, put on the bottom of the appliance, correspond to the available one in the gas network. The adjustment sticker data plate, gives all the appliance’s setting conditions as: gas type and gas operating pressures. Once installed, check there are no leaks using a soapy solution only.

  • Page 9: Conversion

    Remember that the earth wire must not be cut out by the switch. As an alternative, the electrical connection can also be protected with a high sensitivity RCD. ADJUSTING Check the adjustment of the appliance. Before making any adjustment to its operation, ensure proper adjustment to the •...

  • Page 10: Technical Features

    7. TECHNICAL FEATURES BURNERS INJECTORS AND HEAT INPUTS TABLE (for the hob burners lay-out, see on page 4) Injectors Heat Inputs Burners Gases and pressures Rates By-pass diameter (kW) Denomination mbar 1/100 mm Min. 1/100 mm G30 (Butane) 0,75 at 28-30 mbar G31 (Propane) 0,75 Rapid (R)

Table of Contents