Advertisement
Quick Links
1. Names and Parts
1
2
3
4
6
5
7
8
9
10
1 Power Button
4 USB Socket
2 Memory Card Slot
5 NTSC/PAL Switch
3 A/V Out Port
6 Stop/Rec Switch
*No Microphones are available for USA territory.
2. Package Content
3.7V Li-ion BATTERY
BA-PV900FM
Li-ion
CAUTION
Slide the battery into place at approximately 15 degree to avoid
damaging the golden connectors on the units.
C E
Battery
5V Charger
SD Card
Infrared Remote
European Standard
USB Cable
Control
Adapter Head
1
6. Retrieve Files from DVR
There are two ways to read the retrieve video files.
6.1. Use memory card reader to retrieve video files.
6.2. With the device powered on and memory card inserted, connect the
device to PC by USB cable. It will be recognized by PC as an
external drive for user to retrieve the files.
7. Time Setting for Clock Display
1
2
3
4
5
7.1. Insert a safety pin into the reset button
before operation.
3
7.2. Long press
for three seconds to access its time setting mode.
1
2
3
7.3. Press
or
to set hours and press
again to set minutes.
3
To exit time setting mode, press
.
1
7.4. Press
to switch the displaying to 12 or 24 hour format.
7.5. Press
4
to activate the blue LED backlight.
Note: The time setting here is for clock display only. It does not apply to video files.
4
3. Charge Battery
Connect 5V adaptor to DVR
3.1. Remove the back cover from the DVR and connect the charger plug
to the DC In Jack
3.2. Plug the power cord of the charger to an AC wall outlet. The
7 DC In Port
charging starts automatically.
8 Battery Slot
3.3. The LED bar
charging mode. Charging time requires approximately 3 to 4 hours.
9 Reset
3.4. After charging is completed, green light turns off automatically.
10 LED Bar and IR Sensor
3.5. Users may charge the battery while recording.
4. Date and Time Setting for Video Files
4.1. Connect the device to monitor via A/V out cable to enter UI page.
4.2. Use IR remote control aiming at IR sensor to navigate between the
A/V Out Cable
sections.
4.3. Navigate DVR menu by aiming Remote Control to IR Sensor and
scroll down "Program Setting" then "Time Date Setting" to edit
accordingly.
8. Operation
It is highly recommended to format SD card on unit when it is connected
to monitor via A/V out cable.
1
5
8.1. Insert memory card into the card slot
8.2. Power on/off the DVR by pressing power button
8.3. Switch
5
to set NTSC or Pal system
8.4. Switch
6
to Rec/Stop to start or stop recording.
8.5. The default recording mode is motion detect (1 minute)
8.6. LED indicator
Power: Blue
Charge: Green
Record: Red
LED bar
7
10
Charge LED(Green)
When battery is fully charged,
the green LED will turn off.
.
7
will illuminate green to show the device is in
10
2
2
6
5
9
10
2
.
1
.
5
5. Setting
3
10
5.1. Connection
3
Connect AV/Out Cable to the A/V out port
connect the RCA jacks to A/V In port on monitor.
5.2. Operated by infrared controller
Aim the IR remote controller to the IR sensor
navigate the UI by the remote control.
Recorder Setting
Main Menu
Video Files
Normal
Recorder Setting
Motion Detect
Program Setting
Program Setting
Main Menu
Language
Time Date Display
Time Date Setting
MIC
Storage Info
3
PV-FM10
Digital Clock DVR Quick Guide
(Motion Detect)
Law Enforcement Products Manufacturer
Law Enforcement Products Manufacturer
on the device and
on the DVR and
10
Program Setting
Format SD Card
TV Out Setting
Firmware Upgrade
Load Setup Defaults
LawMate
LawMate
®
®
V1.0
Advertisement
