Advertisement
Quick Links
MILLER & KREISEL SOUND CORPORATION 10391 Jefferson Blvd, Culver City, CA 90232 USA 310.204.2854 Fax 310.202.8782
The M&K RM-2 allows you to use all M&K Powered Subwoof-
ers with components that do not have RCA-type subwoofer
output jacks (especially for the MX-125 II, MX-5000THX II, MX-
350THX, MX-150THX, and V-125THX).
It also provides a convenient way to precisely fine tune and
control the level of your M&K powered subwoofer without
having to use the control on the subwoofer's back panel.
LOCATION OF THE RM-2
The RM-2 must be placed close to your amplifier or receiver, so
that its input wires will reach the speaker output terminals of
your component. SPECIAL NOTE: Despite its full Faraday
shielding, in rare instances, when the RM-2 is very close to the
power amplifier, it may be sensitive to hum. If you hear system
hum after connecting the RM-2, move it away from any power
transformers in the receiver or amplifier.
WIRING THE RM-2
The RM-2 has three sets of connectors. From left to right:
RIGHT IN (- connection on top; + connection on bottom)
SUB OUT (2 jacks)
LEFT IN (- connection on top; + connection on bottom)
1. Connect the RIGHT IN wires attached to the RM-1 to the
Right Channel speaker output on your amp or receiver. Make
sure that the Red wire is connected to the (+) terminal on the
amplifier and that the Black wire is connected to the (-) terminal
on the amplifier.
2. Connect the LEFT IN wires attached to the RM-1 to the
Right Channel speaker output on your amp or receiver. Make
sure that the Red wire is connected to the (+) terminal on the
amplifier and that the Black wire is connected to the (-) terminal
on the amplifier.
_
RM-2 HI TO LOW LEVEL CONVERTOR &
REMOTE SUBWOOFER VOLUME CONTROL
_
+
+
RIGHT
LEFT
AMPLIFIER
3. Connect an RCA - RCA interconnect cable from either
one of the SUB OUT jacks on the RM-2 to the LEFT/MONO
input on your subwoofer. If you have two subwoofers, connect
one cable to each subwoofer.
USING THE RM-2 TO SET BASS LEVEL
The RM-2's convenience in setting the bass level of your M&K
subwoofer can be used for various purposes.
The most common purpose is to use it to increase or decrease
bass levels depending on the source. Its calibrated control
makes it easy to return the subwoofer to your reference level.
Here's the procedure:
After connecting the RM-2 as described above, set its level
control to the 0 dB position. Then calibrate the level of the
subwoofer by adjusting the BASS LEVEL control on the back
of the subwoofer. Do not adjust the RM-2. You can calibrate
levels through listening tests, or by using test tones or noise
with a sound level meter or with a third-octave analyzer.
Once calibrated, any time you wish to change the amount of
bass, simply adjust the RM-2. Do not adjust the subwoofer.
The RM-2 has a range of plus or minus 21 dB of adjustment.
Any time you need to reset the bass output to the calibrated
level, all you have to do is set the RM-2 to the 0 dB position!
Another use of the RM-2 is to control (and calibrate) the level
of subwoofers installed in locations that are difficult to access.
In these cases, you may be unable to calibrate bass levels by
using the BASS LEVEL control on the back of the subwoofer.
Under these circumstances, to use the RM-2, just set the
BASS LEVEL control on the back of the subwoofer(s) to
between the 12:00 (straight up) and about the 3:00 position.
Then use the RM-2 to calibrate the bass level.
For more detailed information on the subject of setting bass
levels, see your subwoofer owner's manual.
LOW PASS FILTER
LEFT/MONO
75
(Hz)
+
100
60
FROM PREAMP
PHASE
50
125
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.
ATTENTION:
DEBRANCHER AVANT DE
REMPLACER LE FUSIBLE.
Made in U.S.A.
UTILIZER UN FUSIBLE
DE RECHANGE DE MEME TYPE.
RIGHT
BASS LEVEL
MIN
MAX
CAUTION:
DISCONNECT SUPPLY CORD
BEFORE CHANGING FUSE.
REPLACE FUSE ONLY
WITH SAME TYPE.
120 VAC 50/60 Hz
4 AMP
SLOW-BLOW
RM-2 Manual.pm6
0997rev0
Advertisement
