Table of Contents
Advertisement
======================================================================
Chapter 1. Introduction of Radar.......................................................................................4
1. Introduction ...............................................................................................................4
1-1. Usage of manual .............................................................................................4
2. Composition ..............................................................................................................4
2-1. General............................................................................................................4
3. Specification ..............................................................................................................5
3-1. General............................................................................................................5
3-2. Transceiver......................................................................................................6
3-3. Monitor ............................................................................................................6
3-4. Connection Cable............................................................................................7
Chapter 2. How to operate...................................................................................................8
1. Introduction ...............................................................................................................8
2. How to use the front button and volume ...................................................................8
2-1. How to use direction button .............................................................................8
2-2. How to use the dedicate button.......................................................................8
2-3. Volume adjustment..........................................................................................9
2-4. Screen Description ........................................................................................10
3. Turn ON/OFF .......................................................................................................... 11
3-1. Turn ON......................................................................................................... 11
3-2. Turn OFF ....................................................................................................... 11
3-3. Using time in total .......................................................................................... 11
3-4. How to control power during repair/maintenance .......................................... 11
4. How to use menu ....................................................................................................12
4-1. Screen display...............................................................................................12
4-2. Bearing.................................................................................................................16
4-3. EBL/CSR Read out (Display bearing line/cursor)..........................................17
4-4. Magenetic Var................................................................................................18
4-5. Distance Unit .................................................................................................19
4-6. Wake Point ....................................................................................................20
4-7. Waypoint........................................................................................................21
4-8. Tuning Mode..................................................................................................22
4-9. Timed TX .......................................................................................................23
4-10. TX Period.....................................................................................................24
4-11. Stand-by Time..............................................................................................25
4-12. Alarm Level..................................................................................................26
4-13. TX Pulse ......................................................................................................27
4-14. Target Mag. ........................................................................................................28
4-15. Color Set .....................................................................................................29
4-16. Language Set ..............................................................................................30
======================================================================
1
SMR-3600
Advertisement
Table of Contents
Summary of Contents for Samyung ENC SMR-3600
-
Page 1: Table Of Contents
4-6. Wake Point ....................20 4-7. Waypoint......................21 4-8. Tuning Mode....................22 4-9. Timed TX .......................23 4-10. TX Period.....................24 4-11. Stand-by Time....................25 4-12. Alarm Level....................26 4-13. TX Pulse ......................27 4-14. Target Mag......................28 4-15. Color Set .....................29 4-16. Language Set ....................30 ====================================================================== SMR-3600... - Page 2 3-2. To display the heading in the indicator ............49 4. How to connect to external navigation equipment ..........49 5. Basic knowledge in observation................50 5-1. Scanning range and target ................50 5-2. Navigational reflection wave................51 Chapter 4. Installation......................52 1. Summary.........................52 2. Transmitter / Receiver set up ..................52 ====================================================================== SMR-3600...
- Page 3 1-2. Check out the tightness of screw, bolt ............57 1-3. Check the cabling..................57 2. Transceiver......................57 2-1. Radar Dome ....................57 2-2. Bracket ......................58 3. Monitor ........................58 3-1. Cleaning of a Monitor LCD Screen..............58 Chapter 6. Installation drawing and circuit diagram............59 ====================================================================== SMR-3600...
-
Page 6: Transceiver
: Of 1 % of using RANGE or 70m, below whichever it is bigger • VRM : .000 ~ 64.0 NM – Digital display • EBL : .000° ~ 359° --- Digital display • Synchonizing Method : Manual/Automatic switchable ====================================================================== SMR-3600... -
Page 7: Connection Cable
: Swicth 24) Power : Swicth 25) Transmit : Swicth • Menu type : POP-UP Type 3-4. Connection Cable • Antenna Cable Length : 15m • Power Cable Length : 3m • Data Cable Maximum Length : 3m ====================================================================== SMR-3600... -
Page 8: Chapter 2. How To Operate
: To move Radar plotting to the center position • : Setting up and display NO.1 EBL and VRM • : Setting up and display NO.2 EBL and VRM • : Setting up and display flexile EBL and VRM ====================================================================== SMR-3600... -
Page 9: Volume Adjustment
: Adjust gain of receiving signal • Snow, Rain Clutter elimination : Eliminating the reflected wave due to snow and rain in a heavy weather • Sea Clutter elimination : Eliminating the reflected wave due to sea surface. ====================================================================== SMR-3600... -
Page 10: Screen Description
• Display on top of the screen regarding bearing, speed, latitude and longitude and set-up on right bottom of the screen for destination is only available when the singanl from Gyro Compass and GPS is nput to DATA port. ====================================================================== SMR-3600... -
Page 11: Turn On/Off
Even power is OFF, unt inside still exited especially in Monitor that cause eletric shock while in repair or maintenance. Therefore you are requested to stop the power provided by rectifer (in case of using rectifier), or separate power cable from the rear side of Monitor. ====================================================================== SMR-3600... -
Page 12: How To Use Menu
1) MENU ->[◀][▶] -> [FUNC/DISPLAY SET] -> [▲][▼] -> [HEADING MODE] -> Press ENT button and then there will be a blue line on screen. 2) Select one of [H-UP, N-UP, C-UP] [◀][▶]. 3) Press ESC button after ENT button for the return to screen. ====================================================================== SMR-3600... - Page 13 • Display the other’s bearing in case there’s no connected with Gyro Compass such as the equipment that is able to get bearing information. • Following display is for the screen that there’s GPS or Gyro Compass signal input through data port. ====================================================================== SMR-3600...
- Page 14 • Even the vessel’s stem changed, the image range does not change. • Need the equipment that is able to get bearing information such as Gyro Compass. • Displays stem bearing, speed, longitude and latitude as an option. ====================================================================== SMR-3600...
- Page 15 • Display vessel’s stem bearing, speed, longitude and latitude on screen as option (Notice) It is available to display a data of Gyro Compass and GPS on the screen as above and this is only available for the option. The below shows a screen which is no data input. ====================================================================== SMR-3600...
-
Page 16: Bearing
2) Select true bearing or magenetic bearing by using [◀][▶] button. 3) Press ENT button and ESC button for the return to screen. • It needs the equipment that is able to get bearing information such as Gyro Compass. ====================================================================== SMR-3600... -
Page 17: Ebl/Csr Read Out (Display Bearing Line/Cursor)
-> Press ENT and then there’s a blue line on [EBL/CSR READ OUT]. 2) Select the others or true north] by [◀][▶]. 3) Press ENT and ESC for the return to screen. • It needs the equipment that is able to get bearing information such as Gyro Compass. ====================================================================== SMR-3600... -
Page 18: Magenetic Var
External input GPS DATA. +00.0°: Bearing bearing correction, Input the wanted correction value(-99.9° ~ +99.9°). 3) Press ENT and ESC for the return to screen. • It needs the equipment that is able to get bearing information such as Gyro Compass. ====================================================================== SMR-3600... -
Page 19: Distance Unit
-> Press ENT and then there’s a blue line on [DISTANCE UNIT]. 2) Select [NM, KM] by using [◀][▶] button. NM : Display a distance as Mile. KM : Display a distance as Km. 3) Press ENT and ESC for the return to screen. ====================================================================== SMR-3600... -
Page 20: Wake Point
2) Select [Off, Short, Long] by using [◀][▶] button. Off : No display a target trace. Short : Display a target trace shortly. Long : Display a target trace long. 3) Press ENT and ESC button for the return to screen. ====================================================================== SMR-3600... -
Page 21: Waypoint
3) Press ENT and ESC button for the return to screen. 4) It is necessary GPS bearing information and speed input. • This is only for sending a destination setup data (*BWC signal) from GPS which is available for destination setup to Radar ====================================================================== SMR-3600... -
Page 22: Tuning Mode
1) After check on tuning volume is on center, do not rotate a tuning volume. 2) If tuning volume is rotated, it doesn’t rotate a tuning temporary but rerotate after a couple of scanning. If tuning volume is out of center, it cannot be tuned. ====================================================================== SMR-3600... -
Page 23: Timed Tx
3) Press ENT after ESC for the return to screen. (Notice) Due to Radar’s standby during intermittent transmitting, it needs to be controlled with upmost attention. Otherwise there could be a crash with a vessel with high speed. ====================================================================== SMR-3600... -
Page 24: Tx Period
10-scan : Be in use of 10-scan TX period. 20-scan : Be in use of 20-scan TX period. 30-scan : Be in use of 30-scan TX period. 3) After pressing ENT , press ESC to return back to screen. ====================================================================== SMR-3600... -
Page 25: Stand-By Time
3-minutes : STAND-BY TIME is 3 minutes 5-minutes : STAND-BY TIME is 5 minutes 10-minutes : STAND-BY TIME is 10 minutes 15-minutes : STAND-BY TIME is 15 minutes 3) After pressing ENT, press ESC to return back to screen. ====================================================================== SMR-3600... -
Page 26: Alarm Level
1) MENU -> [◀][▶] -> [RADAR SET-UP] -> [▲][▼] -> [ALARM LEVEL] -> Press ENT to see blue line drawing in alarm level. 2) By using [◀][▶] button to select among [1, 2, 3, 4, 5, 6, 7] 3) After pressing ENT, press ESC to return back to screen. ====================================================================== SMR-3600... -
Page 27: Tx Pulse
Short : The more the transmission pulse is narrow the more distance resolving power is sufficient Long : The more the transmission pulse is broad the more sensitivity is sufficient. 3) After pressing ENT, press ESC to return back to screen. ====================================================================== SMR-3600... -
Page 28: Target Mag
1) MENU -> [◀][▶] -> [RADAR SET-UP] -> [▲][▼] -> [Target Mag.] -> Press ENT to see blue line drawing in target mag.. 2) By using [◀][▶] button to select between [Off] and [On]. 3) After pressing ENT, press ESC to return back to screen. ====================================================================== SMR-3600... -
Page 29: Color Set
1) MENU -> [◀][▶] -> [INIT. SET] -> [▲][▼] -> [COLOR SET] -> Press ENT to see blue line drawing in the color set. 2) By using [◀][▶] button to select among green, yellow, red, white colors and press ENT. 3) After pressing ENT, press ESC to return back to screen. ====================================================================== SMR-3600... -
Page 30: Language Set
1) MENU -> [◀][▶] -> [INIT. SET] -> [▲][▼] -> [LANGUAGE SET] -> Press ENT to see bule line drawing in language set. 2) By using [◀][▶] button to select between Korean, English. Korean : Korean coming up English : English coming up 3) After pressing ENT, press ESC to return back to screen. ====================================================================== SMR-3600... -
Page 31: Simulation
1) MENU -> [◀][▶] -> [INIT. SET] -> [▲][▼] -> [SIMULATION] -> Press ENT to see blue line drawing in simulation. 2) By using [◀][▶] button to select between Off, On. 3) After pressing ENT, press ESC to return back to screen. ====================================================================== SMR-3600... -
Page 32: Outside Color
1) MENU -> [◀][▶] -> [INIT. SET] -> [▲][▼] -> [OUTSIDE COLOR] -> Press ENT to see blue line drawing in outside color. 2) By using [◀][▶] button to select between Black, Blue. 3) After pressing ENT, press ESC to return back to screen. ====================================================================== SMR-3600... -
Page 33: Inside Color
1) MENU -> [◀][▶] -> [INIT. SET] -> [▲][▼] -> [INSIDE COLOR] -> Press ENT to see blue line in inside color. 2) By using [◀][▶] button to select between Black, Blue. 3) After pressing ENT, press ESC to return back to screen. ====================================================================== SMR-3600... - Page 34 GAIN-L SET, STC-H SET and PROGRAM LOAD are radar’s internal set menu, therefore in case of control, following instruction is recommendable. (Notice) Radar internal set menu is value when taking goods out of the warehouse, therefore if user modifies the value, radar capability could be affected. ====================================================================== SMR-3600...
-
Page 35: Bearing Adjust
1)On [INIT. SET], [▲][▼] -> [BEARING ADJUST] -> Press ENT to return back to screen and show BEARING ADJUST value in the middle of upside. 2) By using [▲][▼] [◀][▶], to select BEARING ADJUST value (-90.0 ~ +90.0) 3) After pressing ENT, press ESC to return back to screen. ====================================================================== SMR-3600... -
Page 36: Display Timing
1) [INIT. SET]-> [▲][▼] -> [DISPLAY TIMING] -> Press ENT to return back to screen and DISPLAY TIMING is shown in the middle of upside. 2) By using [▲][▼] [◀][▶] to select DISPLAY TIMING. (000 ~ 255) 3) After pressing ENT, press ESC to return back to screen. ====================================================================== SMR-3600... -
Page 37: Tune Set
1) [INIT. SET] [▲][▼] -> [TUNE SET] -> press ENT to return back to screen and Tune value is shown in the middle of upside. 2) By using [◀][▶] [▲][▼] to select TUNE value. (0 ~ 255) 3) After pressing ENT, press ESC to return back to screen. ====================================================================== SMR-3600... -
Page 38: Turn-R Set
1) [INIT. SET] -> [▲][▼] -> [TURN-R SET] -> Press ENT to return back to screen and Tune-R value is shown in the middle of upside. 2) By using [◀][▶] [▲][▼] to select Tune-R value. (0 ~ 255) 3) After pressing ENT, press ESC to return back to screen. ====================================================================== SMR-3600... -
Page 39: Error Set
1) [INIT. SET] -> [▲][▼] -> [ERROR SET] -> ENT. 2) By using [▶] to select [Off, On]. 3) After pressing ENT, press ESC to return back to screen. (Notice) It should be [ON] status all the time in order to remove ERROR SET. ====================================================================== SMR-3600... -
Page 40: Tx-Time
====================================================================== 4-25. TX-Time • Function to control TX-TIME. 1) [INIT. SET] -> [▲][▼] -> [TX-TIME] -> ENT (Notice) User access to select is prohibited since it is linked with using time of magnetron. ====================================================================== SMR-3600... -
Page 41: Gain-L Setup
2) Use [◀][▶] [▲][▼] buttons to select GAIN-L value. (0 ~ 255) 3) After pressing ENT button, press ESC button. (Notice) When controlling GAIN-L, don’t change the set value because there are some cases of excessive pressure given to the receiver unit. ====================================================================== SMR-3600... -
Page 42: Stc-H Setup
2) Use [◀][▶] [▲][▼] buttons to select STC-H value. (0 ~ 255) 3) After pressing ENT button, press ESC button. (Notice) If STC-H SETUP value is high, targets may disappear at short distance. 4-28. Program Load (Notice) Users must not make any setup for the purpose of program upgrade. ====================================================================== SMR-3600... -
Page 43: Chapter 3. How To Operate
2) Generally as the biggest size of any searched echo reflection, the best gain is the degree that is not contacted echo image by another target. (Notice) If the gain increases too high, noises of the receiver can occur in the display that will normally disturb the search. ====================================================================== SMR-3600... -
Page 44: Radar Interference Removal
(Notice) This function is for the purpose of controlling the echo image by wave but much attention should be paid as the echo images of ships can be repressed at the same time. User can expect a good effect through properly using the gain control function together. ====================================================================== SMR-3600... -
Page 45: How To Measure Distance & Bearing To Target
5) In case of 1 EBL/VRM - F EBL/VRM 6) In case of cursor indication • 1 EBL/VRM • 2 EBL/VRM • F EBL/VRM • 1 EBL/VRM - 2 EBL/VRM • 1 EBL/VRM - F EBL/VRM • Cursor indication ====================================================================== SMR-3600... -
Page 46: How To Use Vrm (Variable Range Maker)
• Press CURSOR button in the front panel. • “+” will be indicated. • Use [▲▼◀▶] button to move and then the distance and bearing will be indicated in the right bottom • Press simply the removal button to eliminate the cursor. ====================================================================== SMR-3600... -
Page 47: How To Move The Center Position On The Screen
○ True north bearing indication : It indicates the bearing which EBL is heading for in case of 0° true north (North Pole) : T ○ Magnetic bearing indication : It indicates the bearing which EBL is heading for in case of 0° north in magnetic compass : M ====================================================================== SMR-3600... -
Page 48: How To Operate Samyung Radar
The higher the number is, only the brighter images react, the lower the number is, the darker images also react. (Notice) If the gain is very good, an alarm may ring through reacting to noise etc.. ====================================================================== SMR-3600... -
Page 49: Other Convenient Functions
4. How to connect to external navigation equipment • This radar is designed to connect to the data terminal at the back panel of the indicator. EARTH DATA 13 12 FUSE(7A) POWER SCANNER CONNECTOR (SCN-16-4P) 1.IN(RX) 2.OUT(TX) 3.GND 4.GND ====================================================================== SMR-3600... -
Page 50: Basic Knowledge In Observation
Therefore, the image should be used to measure the distance to the coastal lines. • Wave route status Sometimes it is impossible to scan the targets behind as the wave is blocked by mountain, rain and snow being on the wave route. ====================================================================== SMR-3600... -
Page 51: Navigational Reflection Wave
PPI screen. This interference turns into various spots and appear in forms of many images but as the interference does not appear in the same place, it can be distinguished from target image. For the radar interference, select『ON』in the function to diminish or get rid of it. ====================================================================== SMR-3600... -
Page 52: Chapter 4. Installation
TRIM is more than half of vertical beam width. * Notice in time of setting up air cables to yachts Yachts navigate on the opposite side of windy direction with condition of inclining a little. If ====================================================================== SMR-3600... - Page 53 * In setting up, make a hole for sibling-tube. Water can’t be protected because of bending sibling-tube if the transmitter / receiver is set up without the hole. * Make installation beam in case of not having enough height for set-up on top of bridge. ====================================================================== SMR-3600...
-
Page 54: Inside Wire Connection
====================================================================== 2-3. Inside wire connection Make hold it with a cable-tie in order to tie-up cables. Don’t bend a connector too strong on putting a cable with a radome. ====================================================================== SMR-3600... -
Page 55: Installation For Instruction-Equipment
* The distance is readjusted with [0 MILE ADJUST] on the Menu List in case the distance displayed on a PPI screen of the radar is different with the actual distance. ====================================================================== SMR-3600... -
Page 56: Packing List
====================================================================== 4-3. Packing list SMR-3600 36 NMile Radar Item External Drawing Dimension Q’ty CH Remark SMR-3600 Monitor CODE NO. SMR-3600 Bracket CODE NO. ACC-RADAR-001 Ø6 × 20 Knob CODE NO. ACC-6X18MM-002 RSU-3600-15M Antenna SRCN2A (Inch cable) CODE NO. RSU-3600-15M 25-16P L=15m CVV-SB2.0 SQ X 2C... -
Page 57: Chapter 5. Maintenance
• In case Raydom surface being contaminated by dust, paint, it may arise the attenuation or reflection of electric wave and cause to lower the performance of Radar, it should be cleaned out by a soft cloth with alcohol to keep it cleaned at all times. ====================================================================== SMR-3600... -
Page 58: Bracket
• Check the mounting of scanner and do painting every half-year to prevent from being rusted. 3. Monitor 3-1. Cleaning of a Monitor LCD Screen • In case a stain adhered to LCD screen, it deteriorates the transparency of LCD screen. • Do cleaning with a soft cloth. ====================================================================== SMR-3600... -
Page 59: Chapter 6. Installation Drawing And Circuit Diagram
====================================================================== Chapter 6. Installation drawing and circuit diagram ====================================================================== SMR-3600...