Rowley NS15 Safety And Operating Instructions

Safety and Operating Instructions
for 2 in 1 Air Nailer/Stapler (NS15)
Important:
Oil stapler BEFORE first use. See page 2.
Please read the safety, operating and maintenance
instructions BEFORE using your 2 in 1 Air
Nailer/Stapler (Stock # NS15).
Please save these instructions for future reference.
2 in 1 Air Nailer/Stapler (Stock # NS15):
Air
Exhaust
Depth/Safety
Adjuster
Nose
Door
Contact Safety Nose
Speci cations:
•Operating air pressure range: 80 -110 psi. 95 psi is
ideal.
• Nail Type: 16 gauge finishing nails
• Nail Length Range:
• Our nail stock #: NS44, NS45, NS46, NS47, NS48.
• Staple Type: 18 gauge narrow crown
• Staple crown width: 5.7 mm.
• Staple leg length range:
•Our fastener stock #: NS40, NS41, NS42.
• Magazine capacity: 140 count 18 gauge staples or
110 count 16 gauge nails.
1
•Hose fitting: / " NPT Milton.
4
Other Features:
•Light weight (Approx. 3.85 lb.) for easy handling.
•Quick-release magazine latch for fast loading.
• Contact safety nose for safe operation.
• Adjustable nail or staple shooting depth.
• Quick release nosepiece to clear jams or debris.
Applications:
• Woodwork construction such as cornices, dustboards
with returns, fascia boards, headboards, furniture
assembly, trim installation, etc.
The following Rowley Co. staples and nails fit the Air/Nailer Stapler (Stock # NS15):
Trigger
Air Inlet
Magazine
Lever Release
Magazine
Lever
Nose
(Fastener
Discharge Area)
Fig. 1
3 / " to 2"
4
5 / " to 1 5 / ".
8 8
Length
Stock #
NS40 1"
1
NS41 1 / "
4
1
NS42 1 / "
2
Safety Instructions:
1. Read and understand all safety, operating and
maintenance instructions BEFORE using tool.
2. Do not use oxygen, flammable gas, or any other
type of gas as a power source. Use regulated,
filtered compressed air only.
3. Do not use gasoline or any other flammable liquid
to clean tool.
4. Do not exceed the maximum operating air pressure
of 110 psi.
5. Always disconnect tool from air supply before
loading fasteners, clearing a jam, servicing, or
adjusting, etc.
6. Always disconnect tool from air supply when not
in operation. Never leave tool unattended while
connected to air supply.
7. Do not carry tool by hose or move tool by pulling
hose. Keep hose away from heat, oil, solvents
and any sharp edges. Replace any damaged,
weak or worn hoses.
8. Do not use tool as a hammer. Do not drop or
throw tool. If the tool is dropped, stop using and
carefully examine any bent, cracked or broken
parts. Listen for air leaks. Do not use tool until
damaged parts are repaired.
9. Always wear safety glasses and ear protection
when using tool.
10. When connecting tool to air supply, only use
couplings that will release all air pressure from
tool when disconnected.
11. Do not point tool at yourself or at any other person.
Always assume that tool contains fasteners. Never
engage in horseplay.
12. Keep your hands or any part of your body away
from fastener discharging area (the nose) when
tool is connected to air supply.
13. Do not drive a fastener on top of other fasteners.
14. Do not touch trigger when connecting or
disconnecting tool to air supply.
15. Do not touch trigger when carrying tool while
connected to air supply.
16. Always keep firm footing when using tool.
17. Do not modify or disable contact safety.
18. Do not modify any part of tool.
19. Keep tool out of reach of children.
20. When not in use, replace air inlet cap.
Fasteners:
Stock #
NS44
NS45
NS46
NS47
NS48
Length
1"
1
1 / "
4
1
1 / "
2
3
1 / "
4
2"
I-50A
-1-