Advertisement
Quick Links
Advertisement
Summary of Contents for First Choice WaveTruck
- Page 1 INSTALLATION MANUAL www.FirstChoicePool.com...
- Page 2 • Check water chemistry. Make sure the pool is free from excess algae to ensure proper operation of the WaveTruck automatic pool cleaner. Never use the WaveTruck automatic pool cleaner to remove plaster/pebble debris in new or remodeled pools. Always remove the WaveTruck automatic pool cleaner before backwashing or chemically shocking the pool. See pages 15-17 for a complete list of replacement parts and kits...
- Page 3 The hoses must be stored straight. DO NOT COIL! Carry the WaveTruck automatic pool cleaner by the handle only. Always install a USPC-approved safety vacuum lock with sidewall connections. When the WaveTruck automatic pool cleaner is removed, make sure the safety vacuum lock wall fitting cap is securely covering the sidewall suction port and snapped shut. SAFETY FIRST!
- Page 4 There are nine connector hoses and one leader hose with a gray hose cuff. The hose cuff connects to the top of the WaveTruck automatic pool cleaner (see Fig. 1). Connect the WaveTruck automatic pool cleaner hose sections together by pushing and twisting the tapered male connector end of each hose firmly into the open female end of the adjacent hose section (see Fig.
- Page 5 STEP 2: CONNECTING TO SUCTION Connect the skimmer cone adapter to the regulator valve and then insert the skimmer cone into: A. The suction port of the skimmer (see Fig. 4) or B. The wall port safety vacuum lock without a three-way or ball valve (see Fig. 5) Without the skimmer cone and regulator valve, insert the male end of the hose directly into the safety vacuum lock wall fitting port with a three-way or ball valve (see Fig. 6) To StarzTruck...
-
Page 6: Step 4: Adjusting Water Flow
STEP 3: TESTING THE FLOW Ensure that the hose is full of water and that your pump is running. Remove the WaveTruck auto- matic pool cleaner from the hose, then insert the flow gauge into the leader hose. Make sure the flow gauge is underwater (see Fig. - Page 7 STEP 5: ADJUSTING YOUR WAVETRUCK AUTOMATIC POOL CLEANER The rear flap tension adjuster is preset to II. When the WaveTruck automatic pool cleaner seems to be spending too much time against steps, vertical walls and other obstructions, turn the rear flap tension adjuster to position I (see Fig.
- Page 8 WAVETRUCK AUTOMATIC POOL CLEANER SERVICE TIPS BOTTOM OPENING REMOVAL AND CLEANING INSTRUCTIONS REMOVING THE BOTTOM OPENING Should the WaveTruck automatic pool cleaner stop moving or become sluggish due to debris trapped in the throat or inside the unit, the turbine/vacuum chamber is accessible following these instructions. 1. Turn off pump. 2. Remove WaveTruck automatic pool cleaner from pool.
- Page 9 WAVETRUCK AUTOMATIC POOL CLEANER SERVICE TIPS CHECK THE CONDITION OF THE SHOES, WINGS AND FLAPS PERIODICALLY The pod shoes and wings have wear indicators on their sides and should be checked occasionally to determine if replacement is needed. The shoe wear indicator is a line on the side of the pod shoe that appears as a difference in texture. When this texture difference is no longer visible at the bottom of the shoe when viewed...
- Page 10 B. Remove the old wings by bending the wings up toward the sides of the cleaner, and lift them off their hooks (see Fig. 12). If any of the wing hooks are broken, take the WaveTruck automatic pool cleaner to your dealer for pod replacement as the cleaner will not function properly if the wings are not properly attached.
- Page 11 Fold the flap in toward the bottom of the WaveTruck automatic pool cleaner. You will feel some resistance at this point (that is normal). As the flap snaps into its normal position, you will feel the spring action and notice that the front flap is now in its normal operating position.
- Page 12 WAVETRUCK AUTOMATIC POOL CLEANER BUMPER REPLACEMENT Replacement of the WaveTruck automatic pool cleaner bumper is not recommended as a “do it yourself” repair, because there is a slight possibility that the replacement might cause a problem in the propulsion system. We strongly suggest that you consult your dealer for this repair.
- Page 13 WAVETRUCK AUTOMATIC POOL CLEANER TROUBLESHOOTING GUIDE PROBLEM: SLOW/NO FORWARD MOVEMENT CAUSES SOLUTIONS Lack of/improper water flow through cleaner Check and adjust water flow, Pg 4 Partial blockage of WaveTruck throat Clear blockage, Pg 6 Worn shoes Replace shoes, Pg 7 Worn wings Replace wings, Pg 8 PROBLEM: CLEANER FAILS TO CLIMB VERTICAL WALLS GUNITE/CONCRETE POOL CAUSES SOLUTIONS Improper shoes for application...
- Page 14 WAVETRUCK AUTOMATIC POOL CLEANER TROUBLESHOOTING GUIDE PROBLEM: CLEANER CLIMBS TO SURFACE AND SUCKS AIR CAUSES SOLUTIONS Too much/improper water flow through cleaner Adjust water flow, Pg 4 Improper tension on rear flap Turn rear flap adjuster to I If still climbing too much, reduce water flow...
- Page 15 D. The integrity of “good” pool plaster is such that the plaster available if you contact your local First Choice dealer. will cause wear on the WaveTruck automatic pool cleaner – not vice versa. 1. The purchase date and purchase location of your WaveTruck automatic pool cleaner.
- Page 16 God, First Choice warrants this cleaner to be free from defects in abuse, misuse, negligence, omissions. materials and workmanship for a period of one year from the original date of purchase subject to all the following conditions 6. This cleaner is intended for a properly designed and...
- Page 17 FIRST CHOICE ALL-AMERICAN REPLACEMENT PARTS FOR THE WAVETRUCK AUTOMATIC POOL CLEANER ™ Top Shell FCH420036 Cone Gear FCH420041 3. Intermediate FCH420043 4. Intermediate Gear Shaft FCH420045 5. Spindle Gear Screw FCH420047 6. Spindle Gear FCH420049 Discover the quality, price and 7. Spindle Gear Bushing FCH420053 selection of these dependable 8. Cone Gear Bushing FCH420053...
- Page 18 FIRST CHOICE REPLACEMENT KITS HWN11601 - POD KIT (WHITE) HWN112 - TURBINE BEARINGS: (2 PACK) (REPLACES AXV417WHP) (REPLACES AXV055P) We’ve made your pool equipment service and repair a lot easier with these convenient replacement kits. Each one is a complete grouping that contains everything you need for that particular repair. For more information or to stock up on...
- Page 19 FIRST CHOICE REPLACEMENT KITS Propulsion/Conversion Kit HWN154 - MED. TURBINE/SPINDLE GEAR KIT HWN160 - PROPULSION/CONVERSION KIT (REPLACES AXV079VP) (REPLACES AXV622DPK) FCH420119 HWN112 - TURBINE BEARINGS: (2 PACK) HWN113 - TURBINE KIT (REPLACES AXV055P) (REPLACES AXV602P / AXV112P) A-Frame and Turbine Kit FCH420031 HWN119 - A-FRAME &...
- Page 20 www.FirstChoicePool.com Rev 01/17 P/N FCTM...