eWON NETBITER EC350 Installation Manual

eWON NETBITER EC350 Installation Manual

Advertisement

Quick Links

1
Before you install the Netbiter, make sure that you have all the necessary
informa on about your local network environment. Contact your network
administrator if in doubt.
Connect Ethernet
Devices to LAN port
See reverse for informa on about the connec ons
2
WAN (enabled by default)
Connect network
to WAN port
PROCEED TO STEP 3

Connect Devices

Connect Serial
Devices
LAN
RS-485 RS-232
PROCEED TO STEP 2

Connect to Network

Select
2G/3G (EC350 only)
Network
Type
Insert the SIM card and
mount the antenna
Make sure that the SIM card has
a mobile data plan and allows
text messaging, and that PIN code
security has been disabled.
3
Connect 12–48 VDC to pin +
Connect Power Ground to pin -

Apply power

Sta c IP or 2G/3G: PROCEED TO STEP 4
DHCP: PROCEED TO SECTION B ON REVERSE
A
LED Name
Color
Modem (EC350 only)
OFF
Steady red
Flashing red
Steady orange
Flashing orange
Steady green
Flashing green
RS485/RS232
OFF
Steady red
Steady green
Uplink/WAN
Steady green
Steady red
Flashing red
Gateway
OFF
Steady green
Flashing green
Steady red
Flashing red
OFF
Power
Steady green
Insert SIM card
S
S
IM
Ethernet Link
OFF
(located on RJ-45 ports)
Orange fl icker
Green fl icker
Apply Power
4
Ethernet with
Sta c IP address
Confi gure IP se ngs.
See sec on C on reverse.
PROCEED TO SECTION B ON REVERSE
Indica on
Possible ac ons
Modem disabled
Modem failure
See the User Manual for more informa on.
SIM card failure
Check that the SIM card is correctly inserted and not damaged.
PIN code enabled on SIM card
Disable PIN code on the SIM card.
No APN server specifi ed
Set the APN (Access Point Name) from the onboard webpage.
Modem registered on mobile network
Modem is searching for mobile network.
Port disabled
Port failure/communica ons issue
See the User Manual for more informa on.
Communica ons OK
Connected to Internet
DHCP:
Check for DHCP server on network.
Incorrect IP se ngs
Sta c IP: Check se ngs for IP address, gateway and DNS.
Unable to connect to Internet
Check network se ngs and fi rewalls.
Unit has no power, or is star ng up
Normal opera on
Firmware update in progress.
Hardware failure
See the User Manual for more informa on.
Applica on failure
See the User Manual for more informa on.
No power
Unit has power
No network detected
To check the mobile signal strength on EC350:
Ac vity on 10 Mbps Ethernet network
Press and release the Mode bu on. The top 5 LEDs
Ac vity on 100 Mbps Ethernet network
will now show signal strength for 60 seconds:
1 Flashing Red LED: No/unknown signal
1 Flashing Orange LED: Poor signal
1 Flashing Green LED: OK signal
2-5 Flashing Green LEDs: Good to op mum signal
Confi gure Network
2G/3G
(EC350 only)
Network
Type
Make sure that there is a
good connec on to the
mobile network.
See LED Descrip ons.
LED Descrip ons

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NETBITER EC350 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for eWON NETBITER EC350

  • Page 1 Connect Devices Apply Power Confi gure Network Before you install the Netbiter, make sure that you have all the necessary informa on about your local network environment. Contact your network Connect 12–48 VDC to pin + administrator if in doubt. Connect Power Ground to pin - 2G/3G Ethernet with...
  • Page 2 Ac vate the Netbiter Local Confi gura on Technical Data The Netbiter must be ac vated to be able to communicate with Netbiter Argos. Local Confi gura on via USB Order Code Dimensions (H x W x D) This requires the System ID and Ac va on Code, both of which are provided on a Connect a USB Micro B cable between a computer and the USB port on the EC310: NB1007 25.6 x 135 x 92 mm...

This manual is also suitable for:

Netbiter ec310

Table of Contents