Oricom AD100 User Manual

Oricom AD100 Aroma Diffuser Night Light
User Guide
Oricom AD100 Aroma Diffuser Night Light
Attention
• The amount and intensity of mist produced will vary, but this is not unusual and
should not be considered a fault. Factors that affect this include water level in the
water tank, water type, humidity, temperature, air currents and so on.
• The unit will not work without water.
• Use 2-3 drops essential oil per 100ML water only. Too much oil will clog the system
and cause malfunction. Please clean the unit as per the maintenance instructions,
before changing to a new type of essential oil.
• Add water first, followed by the essential oil, as the essential oil may block the
Ultrasonic vibration plate and cause malfunction.
Accidental leakage
In the event the unit is knocked over or spillage occurs during use, please follow the
steps below to avoid malfunction.
• Unplug the unit and remove cover.
• Empty water tank.
• Shake the unit gently to drain any water inside the mechanism, and then allow to dry
for at least 24 hours.
Maintenance
After 5-6 uses or 3-5 days of operation, please clean the product as follows:
• Unplug the unit from mains supply and remove cover.
• Unplug power cord from base of unit.
• Add 1 tablespoon of citric acid in the water tank, add just under 100ml of warm
water (up to 70°C).
• Wipe with a soft cloth. Avoid Ultrasonic Vibration plate area, which can be gently
cleaned with a cotton bud.
Oricom AD100 Aroma Diffuser Night Light
User Guide
This Aroma Diffuser uses Ultrasonic waves to continually vaporize water and
essential oil in the water tank, to produce a cool, fragrant mist.
Specifications
Size
Weight
Power adaptor
Length of cord
Power consumption
Time mode
Water capacity
LED light
Original material
Ultrasonic frequency
Operation
1. Connect the AC adaptor to the DC jack at the base of the main body via cable
guide.
2. Remove upper cover. (Fig 2)
3. Add water into the water tank; do not exceed the max line on the water tank. (Fig 3)
4. Drop essential oil into the water tank vertically, the dosage is about 2-3 drops (about
0.1-0.15ML) per 100ML water. (Fig 3)
5. Install the cover of the main body and twist into position.
IMPORTANT: The upper cover must be in position before using the product.
6. Connect power adaptor to a wall plug.
Oricom AD100 Aroma Diffuser Night Light
User Guide
Precautions
• Add water into the water tank first, then drop essential oil into water tank.
• Do not fill over 400ML "MAX" at any time.
• Do not switch on power when the tank is empty.
• Do not touch the Ultrasonic vibration plate.
• Clean regularly as per maintenance instructions to avoid malfunction.
• Always unplug from power supply before maintenance.
• After use, empty remaining water and wipe with a clean dry cloth.
• Essential oil can stain the Ultrasonic vibration plate, please wipe away with a soft
cloth and clean water.
• Do not let mist blow directly onto furniture, clothing, walls etc.
• Keep away from electronic equipment, such as TV and Audio equipment.
• Do not tip the product. This may cause water to enter the mechanism and cause
malfunction.
• Do not use for more than 10 hours continuously.
Wait 60 minutes before restart to avoid damage to Ultrasonic vibration plate.
• Use tap water only. Do not use mineral water, sparkling water etc.
• Do not move product while in use.
• Do not touch any part of the product with wet hands.
• Keep out of reach of children and pets. Also, this appliance is not to be used by
children or persons with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction.
• Keep cord clear of pathways, and do not pull forcefully at any point.
• If smoke or burning smell is detected, unplug immediately.
Oricom AD100 Aroma Diffuser Night Light
User Guide
160(dia)*205mm (height)
470g
100-240VAC 50/60Hz 24V
About 1.2m
7~14W
60minutes/120minutes/180minutes/ON
400ml
6PCS RGB LED
ABS+PP
2.4MHZ
User Guide
Step One
Step Two
FIG 1 FIG 2 FIG 3
7. Press the "ON/OFF" button to turn on. The mist function and light are now on, and
the light will now cycle through the different colours. Choose the duration required
by pressing the ON/OFF button (60minutes /120minutes/180minutes/continuous
spray).
• If there is no water in the water tank, the power will turn off immediately, even
with the power connected.
• Press and hold the "ON/OFF" button for about 2 seconds, and the unit will turn
off.
8. Press "MIST" to adjust the spray intensity. (LOW, MED, HIGH)
9. Press "LIGHT" to keep the colour changing or turn off the light.
• Press the "LIGHT" button for about 2 seconds to cycle through the colours.
10. If you do not use the product for a long period of time, ensure you drain the water
from the water tank, clean the water tank and keep it dry.
NOTE: When the power adaptor is connected, the default setting is off.
Oricom AD100 Aroma Diffuser Night Light
User Guide
FIG 4
User Guide