Brain Bee B-TP 1000 Quick Manual

Tpms scantool

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

B-TP 1000

TPMS SCANTOOL

Quick Guide

ENGLISH

Ver. 1.3

Table of Contents

Need help?

Do you have a question about the B-TP 1000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Brain Bee B-TP 1000

Page 1 B-TP 1000 TPMS SCANTOOL Quick Guide ENGLISH Ver. 1.3...
Page 3: Table Of Contents
ACTIVATION, UPDATE AND LICENSE RENEWAL OF B-TP 1000 ................16 The upgrade and license renewal of the B-TP 1000 takes place during the connection of the scantool to the PC, switching it into "ITALSENSOR TOOL MANAGER" mode and connecting it via the USB cable.
Page 4: General Notes
All rights reserved. Total or partial copy of this manual is prohibited under any form, either paper forms or electronic forms. BRAIN BEE SPA and resources used for the drawing up of this manual will not be held responsible for the incorrect use of the manual, while guarantee that information in the manual have been duly checked.
Page 5 B-TP 1000 Battery use and safety Warning: The equipment includes two Li-ion batteries. These batteries can only be replaced by Brain Bee authorized technical service centre. Recharge the batteries using the battery charger or the battery power cable supplied with ...
Page 6: General Technical Features
Diagnosis of indirect systems can be done with a scantool of the Touch line connected in bluetooth mode to the B-TP 1000. Any malfunction is detected using the ABS, ESP rpm sensors: the presence of a flat tyre can be detected based on the rotation speed of every single tyre.
Page 7: Accessories Coming With The Equipment
B-TP 1000 Reading of the characteristic parameters of the original sensor via radio (UHF – 433 MHz)  Battery status Sensor ID (both decimal and hexadecimal) Tyre pressure Tyre temperature Realignment of TPMS sensors on the vehicle in case of “tyre change” or sensor replacement ...
Page 8: Database
Keep the database updated by downloading it from the website and reprogramming the equipment using the USB cable supplied, as outlined in the paragraph ACTIVATION, UPDATE AND LICENSE RENEWAL OF B-TP 1000. DESCRIPTION OF KEYPAD AND CONTROLS ON/OFF key: press to turn on the equipment. Keep it pressed for at least 2 seconds to turn off the equipment.
Page 9: Menu Structure
PRINT LEARNING MAC ADDRESS PROCEDURES TEST RADIO CONTROLS LANGUAGE MANUAL: DIRECT UP&GO TPMS UNITS OF MEASURE MANUAL: SYSTEM GARAGE DATA INDIRECT TPMS INFO POWER SAFE SETUP RESERVED The diagram above shows the schematic structure of B-TP 1000 software menus. ENGLISH...
Page 10: Main Menu And Status Bar
B-TP 1000 MAIN MENU AND STATUS BAR Indicates the battery status: Indicates menu or charging vehicle selected 100% charged 75% charged Indicates bluetooth 50% charged connection to the running out EOBD port of the Indicates USB Indicates bluetooth vehicle by means of...
Page 11 B-TP 1000 CORRECT POSITIONING OF THE EQUIPMENT ON THE TYRE FOR READING PURPOSES The correct positioning of the equipment on the sensor ensures the radio communication for the activation and decoding of the sensor itself. Position the equipment on the tyre, at the same height as the TPMS sensor, directing the aerial towards the sensor, as shown above.
Page 12: Correct Positioning Of The Equipment On The Sensor For Programming Purposes
B-TP 1000 CORRECT POSITIONING OF THE EQUIPMENT ON THE SENSOR FOR PROGRAMMING PURPOSES Warning! We recommend programming the sensors before installing them onto the tyre. Position the equipment in line with the valve, in contact with it or at a distance not greater than 5 cm.
Page 13: Sensors Replacement
B-TP 1000 The pressure measured by the sensor in Psi or bar according to the equipment settings  The temperature measured by the sensor in °C or °F according to the equipment settings  Indicates the position of Indicates the status of...
Page 14: Copy Sensor Id
ID: allows copying the ID code of the faulty sensor to be replaced (if it can be read using B-TP 1000) and programming it into a universal sensor create sensor ID: allows creating a random ID code to program a universal sensor...
Page 15: Create Sensor Id
B-TP 1000 Position the equipment close to the universal sensor to be programmed with the ID code previously copied and press the key CREATE SENSOR ID Position the equipment close to the sensor and press the key to program it with a random ID code generated by the equipment according to the sensor manufacturer previously selected.
Page 16: Enter Sensor Id
B-TP 1000 ENTER SENSOR ID Enter the ID code selecting the numbers and letters from the keypad on the screen using the arrow keys and confirming with the key Position the equipment close to the sensor and press the key to program it with the ID code previously set.
Page 17: Technical Information
In case of EOBD procedure, you will have to connect the optional accessory, B-TP EOBD, or a  device of the Touch line, to the vehicle EOBD socket: B-TP 1000 will read in sequence all the IDs of the TPMS sensors fitted on the vehicle and will transmit them via Bluetooth to the accessory connected to the EOBD socket, which will then inform the vehicle ECU about the new ID numbers or the new position of the TPMS sensors fitted into the tyres.
Page 18: Warning: To Download Updates And Allow The Program To Renew The Instrument License, The Pc Must Be Connected To The Internet
Within the disk, run setup.exe to install ITALMATIC TOOL MANAGER on the PC At the end of the operation, switch off the B-TP 1000 and disconnect it from the PC At the end of the installation, an icon is created on the PC desktop, for the following uses of the program;...