Gigabyte R151-Z30 Hardware Quick Installation Manual

1 Default
Clear CMOS PMBUS Addr
2
CLR_CMOS
Enable
3
32 1 2
31
23
24 25 26 27 28 29 30
10
22
Default Enable
S3 Power On Select
S3_MASK
3 2
21
20
19
CPU
18
17 15
16 14
Enable Default
BIOS Recovery
BIOS_RCVR
3 2 1
Fan Duct
2
1
System Fan
1
System Cover
1
3
1
2
RAID SKU LED1
Disk LED
(LED on
Back Panel)
No RAID configuration
(via HBA, ICH)
Removed HDD Slot
(LED on Back Panel)
Disk LED
RAID configuration
(via HW RAID Card or
SW RAID Card)
Removed HDD Slot
(*1) Depend on HBA/Utility Spec.
(*2) Blink cycle depend on HDD's activity signal.
(*3) If HDD is pulled out during rebuilding, Disk status of this HDD is regarded as fault.
1
2
R151-Z30 Hardware Quick Installation Guide
Motherboard Components
No. Description
1 Chipset
1 ID button with LED
2
PMBUS_SEL
BMC
3
2 USB 2.0 ports
3 4 5 6 7 3 Server management LAN port (top)/USB 3.0 port (bottom)
4 SFP+ LAN port #1 active/link LEDs
5 SFP+ LAN port #1/SFP+ LAN port#2
6 SFP+ LAN port #2 active/link LEDs
7 Serial port (top) / VGA port (bottom)
8 PMBus connector
9 BMC firmware readiness LED
10 TPM connector
11 2 x 12 pin main power connector
11
8 12 2 x 4 pin power connector (for memory)
9
13 2 x 4 pin power connector (for CPU)
12 14 Slimline connector #0 (SATA 6Gb/s signal)
15 Slimline connector #1 (SATA 6Gb/s signal)
13
1
16 Slimline connector #2 (SATA 6Gb/s signal)
17 Slimline connector #3 (SATA 6Gb/s signal)
18 Front panel header
19 HDD back plane board header
20 M.2 slot (Gen3/x4)
21 USB 3.0 header
22 USB 2.0 header
23 Serial port cable connector
24 PCIe x16 slot (Gen3/x16)
25 PCIe x8 slot (Gen3/x8)
26 PCIe x16 slot (Gen3/x16)
27 PCIe x16 slot (Gen3/x16)
28 PCIe x16 slot (Gen3/x8)
Enable Default
Password Clear
29 PCIe x16 slot (Gen3/x16)
BIOS_PWD
3 2 1
30 PCIe x8 slot (Gen3/x8)
31 Battery socket
32 IPMB connector
PCI Express Card
3
4
6
1
2 5
Solid State Drive
2
1
Hard Disk Drive
2
Hard Disk Drive LED
HDD
Locate Rebuilding
Fault
Green ON(*1) OFF
Amber OFF OFF
Green ON(*1) OFF
Amber OFF OFF
Green ON OFF
Amber OFF ON
ON(*1) OFF
Green
Amber OFF ON
Power Supply
Power Supply Status LED
State
Off No AC power to all power supplies
0.5Hz Blink/Red No AC power to all power supplies
Blink/Green
Only standby output on
Green Power supply DC output ON and ready
Green Power supply failure
0.5Hz Blink
Power supply warning
Red /Green
NOTE! Blinking frequency : (0.5sec on/ 0.5 sec off)
Memory
DDR Population Table
DIMMs
DIMM0 DIMM1
Populated
1 -- 1
2 1 1
RDIMM Maximum Frequency Supported Table
DIMM Frequency (MT/s)
2R
DIMMs
2DR
Populated
1R 4DR
2S2R
2S4R
-- --
1
-- --
1
1
-- --
1 Not Supported
2 -- --
--
1 1
-- --
2
2
-- --
2
Not Supported
--
1 1 Not Supported
--
1 1 Not Supported
3
Front
1
4
Rear
LED1
LED2
HDD HDD Present
Access (No Access)
Green OFF
Amber OFF
Green --
Amber --
Alternately OFF
(Low Speed: 2 Hz) OFF
(*3)
--
No.
--
(*3)
1
2
3/4
5
6
Description
7
8
System Components
1
2
4
3
3
9 8 7 6 5
M2.6
10
CPU/Heat Sink
External cap
1
2
3
1
3
4
1
2
9
3
8
7
1
LRDIMM Maximum Frequency Supported Table
DIMM
DIMMs
Populated
1R 2S4R
--
1
--
1
1
-- --
1.2V
2 --
1
1
2667
--
2
2
2400
-- --
--
1
2133
--
1
2133
NOTE!
 1R: 1 package rank of SDP DRAMs
2133
 2R: 2 package rank of SDP DRAMs
 2DR: 2 package rank of DDP DRAMs
 4DR: 2 package rank of DDP DRAMs
 1S2R/1S4R/1S8R: 1 package rank of 2/4/8 high 3DS DRAMs
 2S2R/2S4R/2S8R: 2 package rank of 2/4/8 high 3DS DRAMs
 DIMM must be populated in sequential alphabetic order, starting with bank A.
 When only one DIMM is used, it must be populated in memory slot A1.
System Appearance
HDD #1
HDD #0
No. Description
1 USB 3.0 ports
2 ID Button with LED
3 Power Button with LED
1 2 3 4 5 6 7 8
No. Description
1 Secondary Power Supply Module
2 Primary Power Supply Module
3 Serial Port
4 VGA Port
5 GbE LAN Port
6 Server Management LAN Port
7 USB 3.0 Ports
8 USB 2.0 Ports
9 ID Button with LED
Front Panel LED and Buttons
1 2 3 4 5
Name Color Status
Press the button to enable NMI function.
NMI Button
Reset Button Press the button to reset the system.
Green Solid On Link between system and network or no access.
LAN1/2
Active/Link LEDs
Green Blink Data transmission or receiving is occurring.
N/A Off No data transmission or receiving is occurring.
On HDD locate
HDD Status LED
Green
Blink HDD access
Amber On HDD fault
Green/
Blink HDD rebuilding
Amber
N/A Off No HDD access or no HDD fault.
Solid On
System Green System is operating normally.
Status LED
Critical condition, may indicates:
System fan failure
Solid On
System temperature
Non-critical condition, may indicates:
Amber
Redundant power module failure
Blink
Temperature and voltage issue
Chassis intrusion
System is not ready, may indicates:
POST error
N/A
Off
NMI error
Processor or terminator missing
ID Button Press the button to activate system identifcation.
Power Button Green Solid On System is powered on.
with LED
Green Blink System is in ACPI S1 state (sleep mode).
System is not powered on or in ACPI S5 state.
(power off).
N/A Off
System is in ACPI S4 state (hibernate mode).
No. Description
1 PCI Express card bays
2 Power supply unit
3 DDR4 Memory
4 CPU/Heatsink
5 System fan #1
6 System fan #2
7 System fan #3
8 System fan #4
9 System fan #5
10 Hard Disk Drives
4
2
5
6
2
3
Frequency (MT/s)
1.2V
4DR
-- Not Supported
2667
--
1 2667
-- Not Supported
Not Supported
--
-- 2133
2 2133
Not Supported
1
1 2133
1 2 3
HDD #2 HDD #3
9
6 7 8
Description