TP-Link RE200 Quick Installation Manual

Quick
Installation
Guide
AC750 WiFi Range Extender
RE200
Two easy setup options:
Option 1: Using a Web Browser
Option 2: Using WPS (Wi-Fi Protected Setup)
1
Using a Web Browser
1 Power On
Plug the extender into an electrical outlet
near your router, and wait until the Wireless
LED is lit and solid green.
Con gure
4
Follow the Quick Setup Wizard to con gure the extender.
A. On the Start screen, click Next.
Start Choose Region
Main Router/AP WiFi Network Name(SSID):
Wi-Fi Network Name_2.4GHz:
Wi-Fi Network Name_5GHz:
Connection Status:
Please click Next to set up the Range Extender or click Exit to go to the Device Management Page.
D. Enter your router's Wi-Fi password and
either choose Copy from Main Router or
Customize to create a name for the 2.4GHz
extended network, then click Next.
Start Choose Region
Main Router/AP Network (2.4GHz)
Main Router/AP WiFi Network Name(SSID):
Main Router/AP MAC Address(BSSID):
WiFi Security Option:
Fill in the WiFi Password of your Main
Range Extender Network (XXGHz)
Range Extender WiFi Network Name(SSID):
5 Relocate
A. Plug the extender into an electrical outlet
about halfway between your router and
the Wi-Fi dead zone.
B. Wait about 1 minute until the
corresponding LEDs ( 2.4G and 5G ) are lit
and stay solid.
Solid green
Solid red
O
B. Choose your region from the Region drop-down
Wireless Settings Review Settings
N/A
N/A
Disconnected
Exit Next
E. Repeat step C and D to extend the 5GHz wireless
Wireless Settings Review Settings
TP-LINK_2.4GHz_XXX
00-0A-EB-74-06-06
Most Secure(WPA-PSK/WPA2-PSK)
123456789
Router/AP:
Copy from Main Router/AP TP-LINK_2.4GHz_XXX
TP-LINK_2.4GHz_XXX_EXT
Customize
Back Next
Good connection
Too far away from the router
No connection
LEDs
2.4G and 5G
Red – During boot up, reset, or weak wireless signal.
Green – Strong wireless signal.
OFF – The extender is not connected to 2.4GHz or
5GHz Wi-Fi bands of your router.
Wireless Signal
ON – The wireless is enabled.
OFF – The wireless is disabled.
Ethernet
ON – A device is connected via the Ethernet port.
Blinking – The Ethernet port is transmitting data.
OFF – No device is connected via the Ethernet port.
2 Connect
Disconnect the Ethernet (wired) connection to
your computer. Click the Wi-Fi icon on the
taskbar and connect to the Extender's network
(e.g. TP-LINK_Extender_XXGHz). No password is
required to connect the rst time.
Not connected
Connection are available
Wireless Network Connection
TP-LINK_Extender_XXGHz
Connect automatically Connect
√
list and click Next.
Note: Per FCC regulations, all Wi-Fi products marketed in the
U.S. are xed to the U.S. region only.
Start Choose Region Wireless Settings
Region: Please Select Your Region
Please select your own region to prevent illegal usage against the local law.
Exit Next
network.
Start Choose Region Wireless Settings
Main Router/AP Network (5GHz)
Main Router/AP WiFi Network Name(SSID):
TP-LINK_5GHz_XXX
Main Router/AP MAC Address(BSSID):
00-0A-EB-74-06-06
WiFi Security Option: Most Secure(WPA-PSK/WPA2-PSK)
Fill in the WiFi Password of your Main 123456789
Router/AP:
Range Extender Network (XXGHz)
Range Extender WiFi Network Name(SSID): Copy from Main Router/AP
Customize
Back Next
Main Network
Both 2.4GHz and 5GHz extended networks share the same Wi-Fi password as your main network, but
may have di erent wireless network names if you customize the names during the con guration.
ON – The extender is powered on.
Blinking – WPS connection is in process.
ON – WPS connection is successful.
OFF – The extender is not connected to
your router by WPS.
RESET – This button resets the extender to its
factory default settings.
ETHERNET port – Used to connect an
Ethernet-enabled device to the wireless
network.
Login
3
Launch a web browser and type
http://tplinkrepeater.net in the address eld.
Use admin (all lowercase) for both Username
and Password to log in.
http://tplinkrepeater.net
Username:
Password:
C. Select your router's 2.4GHz wireless network
name (SSID), or select Skip to skip this band and
click Next. If the SSID is hidden, select Set SSID
and MAC manually.
Review Settings
Start
Available Wireless Networks (2.4GHz): 24
Choose SSID
TP-LINK_2.4GHz_XXX
√
TP-LINK_XXX
Set SSID and MAC Manually
Skip (I don't want to use this band)
F. Verify your Wireless Settings and click Finish.
Both 2.4G and 5G LEDs should turn on.
Review Settings
Start
Wireless Setting
Main Router/AP WiFi Network Name (2.4GHz):
Main Router/AP WiFi Network Name (5GHz):
Range Extender WiFi Network Name (2.4GHz):
Range Extender WiFi Network Name (5GHz):
TP-LINK_5GHz_XXX
TP-LINK_5GHz_XXX_EXT
Export Settings
Extended Network
5G
2.4G
Ideal Range Extender Placement
Power
RE
RESET
RESET ETHERNET port
ETHERNET
admin
admin
Login Cancel
Choose Region Wireless Settings Review Settings
Signal MAC Channel Security
00-0A-EB-74-06-06 1 WPA-PSK
0C-72-2C-B3-A5-2C 1 WPA-PSK
Back Rescan Next
Choose Region Wireless Settings Review Settings
TP-LINK_2.4GHz_XXX
TP-LINK_5GHz_XXX
TP-LINK_2.4GHz_XXX_EXT
WiFi Security Option: Most Secure (WPA/WPA2-PSK)
WiFi Password: 123456789
TP-LINK_5GHz_XXX_EXT
WiFi Security Option: Most Secure (WPA/WPA2-PSK)
WiFi Password: 123456789
Back Finish