Advertisement
JA-120PC (90) PIR motion BUS detector with a 90° verification camera
the number of taken and transferred photos may be tripled (18/24 photos).
Applies to Instant/Delayed reactions.
Installation recommendations, cautions
Several JA-120PC (90)s can be installed in the system. However, triggering
several detectors at the same time will extend the transmission time of photos
to the control panel and to the external storage. Complete transmission can take
a few minutes.
Installation in the corner of a room requires more attention during testing
due to possible reflections of the flash on the photographed scene (especially
in the dark).
In order to take a photo using a PG output, use the F-Link software and
set the Impulse parameter in the PG outputs / Function menu to a time of at
least 1 min. The PIR is limited to taking 1 requested photo by PG status per
minute.
The number of pre-alarm photos taken by a PG output is limited to 40
photos/day/control panel. The photo counter is reset at 00:00 hrs. Alarm
photos and photos requested in MyJABLOTRON have no limitation.
When you start transferring the pictures to MyJABLOTRON or external
mass storage, it's necessary to take into account the cost of data transfer
to be paid to your GSM provider When LAN communication is not available.
Detection characteristics
The PIR detector has a 90°/12m coverage – see the picture below.
The detection characteristics of the PIR part has no influence on the camera
part of the detector.
Warning:
-
The lens cannot be changed for other types.
-
The camera has a viewing angle of 90°, the camera flash has a range
of 3 m.
Side wiew
Saving and browsing the photos
Every photo is taken twice: the first in low resolution (LQ = 320x240 pixels), the
second in high resolution (HQ = 640x480 pixels).
All of the exposures are saved into independent folders Foto_LQ and Foto_HQ
on the Micro SD card. When the card's capacity is full, the oldest photos will be
replaced with new ones. Photos saved on the micro SD card can be browsed
in a photo browser on a PC.
Note: Some antivirus software may write its own data on the Micro SD card.
The detector will automatically format an SD card marked this way. SD card
formatting erases all data which has been saved. For more information about
formatting see Formatting the Micro SD card .
Photos are sent to the control panel in LQ. You can browse through these
images in F-Link and J-Link software, event memory by clicking on an event
called New image. Pictures are displayed in LQ, if you click on Detail you can get
second-exposure photos (HQ). Images can be searched and browsed by a file
manager or picture browser. In order to display the photos this way it is necessary
to start F-Link (J-link) software, be logged into the control panel as a service
technician or Administrator and then load the control panel memory.
Disc: Flexi_log /Foto. Here are all the photos which have been sent to the control
panel (LQ) and photos which have been requested in Detail (HQ).
Picture transmission from the control
It's necessary to choose one of these options in order to send photos to the user:
Transfer of pictures to MyJABLOTRON
When the customer uses MyJABLOTRON services, then the customer has
direct access to the photos from this service. Parameter settings
of the transfer of pictures are done during the panel registration.
All the photos are delivered and visible in MyJABLOTRON. Every single
photo can be requested in HQ resolution. There you can also choose
telephone numbers (for SMS) or e-mail addresses which will receive
a message when a new picture is taken. MyJABLOTRON can request a new
JA-120PC (90) BUS PIR motion BUS detector with a 90° verification camera
Top view
panel
picture without PG output activation (see Installation recommendations,
cautions).
MyJABLOTRON respects permissions of individual users concerning
photo verification accordingly to sections to which the users have access
(for example, a user from section 1 cannot browse through photos from
section 2)
Transfer of pictures to external mass storage
If MyJABLOTRON is not available, photos can be transferred to external mass
storage http://img.jablotron.com. Communication parameters are preset
in the factory and are activated when the first PIR detector with a camera
is enrolled in the system and after agreeing with pictures transfer.
When communication works properly the user must create an account
at
http://img.jablotron.com
by entering the login and password, and then
filling in the registration code of the control panel which will make photos
available for browsing. The registration code is on the control panel PCB
or you can read it via F-Link software, Communication tab, Registration
code field.
Reports of new photos stored in this mass storage can be sent
to an e-mail.
Note: If there are more detectors in the premises, all photos will be visible
to all people with access to the created premises regardless of the sections
assigned to them.
Photos stored at
http://img.jablotron.com
Photos in HQ quality cannot be requested.
In both cases sending reports straight from the control panel will normally
work.
When
the
picture
http://img.jablotron.com, the control panel will send an SMS report to all
users depending on the settings in F-Link, User reports tab, Alarm photo
settings. Sent SMSes include an http link to display the photo. The photos
can also be browsed on mobile phones with a connection to the internet.
WARNING:
-
This detector allows you to take photos by PG output reaction or from
MyJABLOTRON even when the system is unset. The manufacturer
strictly warns the user that the detector has to be used within the limits
given by particular laws or norms, especially laws about the protection
of personal privacy.
-
The use of the detector is also subject to regulations on the protection
of personal data and the manufacturer recommends that users be aware
of the obligations applicable to the operation of CCTV.
-
According to these regulations users have an obligation to ensure
the approval of persons in range of the detector during the acquisition
of video recordings or the obligation to indicate the image capture area
by information tables.
Formatting the Micro SD card
The detector is supplied with a formatted Micro SD card (15). The yellow
indication LED (16) is turned off in normal detector mode. Slow LED flashing
indicates that the card was removed while data was being written on it,
or it has been changed for another SD card. The detector will work normally
with a new SD card only if the detector performs a card formatting.
Formatting the SD card is started by pressing the tamper contact (13).
The formatting procedure is indicated by quick flashing of the yellow LED
indicator (16). During this process all photos on the SD card will be erased,
however a backup of the photos is in the event memory log, alternatively
in external storage.
Technical specifications
Power
from the control panel BUS +12 V (+9 ... +15 V)
Current consumption
- nominal for the backup supply calculation
- maximum for cable choice
Recommended installation height
PIR detection angle / detection coverage:
Horizontal camera capture angle
Range of the flash
Camera resolution
Photo size LQ/HQ (typically)
Typical (LQ) photo transmission time to the control panel
Ideal (HQ) photo transmission time to the control panel
Typical photo transfer time to the server
Dimensions, weight
Classification
- according to
- operational temperature range
- operational environment
- certification body
Also complies with
JABLOTRON ALARMS a.s. hereby declares that the JA-120PC
(90) is in a compliance with the relevant Union harmonisation
legislation: Directives No: 2014/30/EU, 2011/65/EU. The original
of
the
conformity
www.jablotron.com - Section Downloads.
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer
or directly to the manufacturer after use.
2 / 2
are available only in LQ quality.
is
saved
in
MyJABLOTRON
250 mA (with high flash intensity)
2.5 m above the floor
max. 3 meters
LQ 320x240; HQ 640x480 pixels
2-20kB / 2-64kB (6kB / 35kB)
up to 20 s. (10 s)
up to 130 s (60 s)
15 s / GPRS; 2 s / LAN
110 x 60 x 55 mm, 102 g
Security grade 2 / Environmental class II
EN 50131-1, EN 50131-2-2
-10 to +40 °C
indoor general
Trezor Test s.r.o. (no. 3025)
EN 50130-4, EN 55022
assessment
can
be
found
MMP53102
or
5 mA
90°/12 m
90°
at
Advertisement
