Visiotech T5Pro Installation Instructions

Package list
1 Reader Instruction Package
考 勤 门 禁 一 体 机
装箱清单
1 主产品 2 资料包 配件包 数据线
7 0/ c/ 1 4 6 5 OK / M 8 9 2 3
Copyright ANVIZ All rights reserved. CD-ROM EN CH COMPACT Windows 98 windows Windows XP Windows 2000 FOR Windows 7 Windows Vista P1 P2 P3 P4
http://www.anviz.com
安装示意图
2 1 安装步骤
1 按后挂板孔位在墙上进行钻孔 Access control
2 安装固定后挂板，接好相关连线
3 固定主机
3
排线说明
FOR
1 P Windows 98 windows
功能 1 粗黑 线 颜色 描述 E N C H CD-ROM COMPACT Windows 2000 Windows XP
12V COM 继电器 P3 6 8 7 NO COM NC 电源 2 粗红 DC12V 电源 GND Windows Vista
P3 继电器 COM DC12V 7 6 P 2 Windows 7
12V COM 8 DC12V 功能 线 颜色 描述
2 P P 1 3 P 1 绿 韦根 DATA0 输出
韦根输出 3 2 白 黑 韦根 DATA1 输出
4 黄 RS485A GND
TCP/IP RS485 6 5 黑 紫 RS485B
GND
P 3
P 4 门磁 功能 1 线 颜色 紫 触发输入 描述
出门按钮 2 黄 触发输入
4 3
4 P 功能 线 颜色 描述 接地 6 5 黑 绿 GND
门铃 1 白 触发输出 继电器 7 橙 NC/DC12V COM
2 白 触发输出 8 蓝 NO/DC12V
特别说明：门禁机是高度集成化的精密电子产品，任何错误的连接都可能导致
门禁机的元器件损坏，因此连接各种设备之前，请仔细阅读接线说明。
Installation Diagram
1
2
3
Wiring Instruction
The interface marked with for specific models,
Please according to the practical device to wiring.
2
P
P 1
P
Relay states
RJ45(TCP/IP)
6 COM
P 3
Relay 7 NC
8 NO
6 COM
P 3 Relay
7 DC12V
8 DC12V
Important notice: Please carefully follow this wiring diagram, If the reader gets damaged by
incorrect wiring then your warranty will be void.
Accessory Package Connector Jack
P1 P2 P3
Installation Steps:
1
Drill holes in the wall follow the hole position on back panel
2
Install and fix back panel, connect related cables
3
Fix access control reader
1
P
Cable
Function PIN
Description
Color
1 Red
DC12V
Power
2 Black
GND
P 2
Cable
Function PIN Description
Color
1 Green Wiegand DATA0 Output
Wiegand
2 White Wiegand DATA1 Output
Output
3
Black GND
3
4
RS485A
Yellow
5
RS485 Purple RS485B
6 Black
GND
3
P
Select either
Cable
Description
12 volt out on Function PIN
Color
COM or voltage
free contact.
1 Purple Trigger Input
Door Sensor
2 Yellow Trigger Input
Exit Button
3 White
4 White
Black
5
GND GND
Green
6 COM
7
Relay Orange NC
8 Blue NO
Access Control Reader & Power Supply
P1
Port
PIN 1 2 8
12V COM Power Supply Output Controller
Function
Connector +12V GND NO
+
Relay State
RJ45 USB
+
Mark
+12V GND PUSH
Access Control Power Supply
Access Control Reader & Controller
P1
Port
PIN 1 2 6
Function Power Supply RS485
+12V GND GND
Connector RS485B RS485A
Mark +12V GND
Switch Power
Access Control Reader & Switch Power Supply
P3
Port
7 6 5 4 3 2 1 PIN
Exit Door
GND
12V COM
Function
Button sensor
NC COM GND OPEN DOOR Connector
+
Relay State
Door Sensor
Power on
to unlock
NO GND NC Mark
+
Power off to unlock Switch Power Supply
Communicate with PC
P2
5 4 3 2 1
Wiegand Output
GND D1 D0
TCP/IP
GND D1 D0 Mark
Access control
V1.4
P1 P3
1 2 8 7 6 5 4 3 2 1
Exit Door
Output Controller GND
Power Supply
Button sensor
+12V GND NO NC COM GND OPEN DOOR
Diode
+
Power off
to unlock
+
Diode
Power on
to unlock
+12V GND
Door Sensor
RS485
Mini-USB