Advertisement
House
DIP SWITCH POSITIONS
2
3
4
5
ID
0
–
–
–
–
1
–
–
–
–
2
–
–
–
ON
3
–
–
–
ON
4
–
–
ON
–
5
–
–
ON
–
6
–
–
ON
ON
7
–
–
ON
ON
8
–
ON
–
–
9
–
ON
–
–
10
–
ON
–
ON
11
–
ON
–
ON
12
–
ON
ON
–
13
–
ON
ON
–
14
–
ON
ON
ON
15
–
ON
ON
ON
"–" indicates "OFF."
SW-1
NOT USED
Figure 4. DIP Switch Settings
RELAY and LED Operation
The 5800RL contains two relays (figure 2) (SPDT, rated 2A,
28VAC/VDC) that may be used to activate remote sounders and/or
remote arm/disarm indicators. There are three LEDs (green, yellow,
red) located above the DIP switch and one LED (red) located
approximately in the center of the pc board. The LEDs located
above the DIP switch, indicate power and relay activity. Refer to
Figure 5. The RF Interference LED monitors local radio frequency
interference. If this LED is continuously lit, the 5800RL should be
relocated.
Relay
LED
Activates Upon
Indicates an alarm condition as follows:
A
Yellow
Steady On = burglary alarm (NO
connects to COM)
Temporal ON = fire alarm (NO connects
temporal to COM)
OFF = no alarms present (NC contact
connects to COM)
Indicates system armed/disarmed as
B
Red
follows:
ON = system armed away, stay, or
instant (NO contact connects to COM)
OFF = system disarmed (NC contact
connects to COM)
Normally on (lighted) when power is
N/A
Green
applied. Flickering indicates RF is being
processed.
N/A
RF
Lights when RF activity is present.
Inter-
ference
Figure 5. Relay and LED Operation
¬N 9l
K3790 01/01
www.PDF-Zoo.com
House
DIP SWITCH POSITIONS
6
2
3
4
ID
–
16
ON
–
–
ON
17
ON
–
–
–
18
ON
–
–
ON
19
ON
–
–
–
20
ON
–
ON
ON
21
ON
–
ON
–
22
ON
–
ON
ON
23
ON
–
ON
–
24
ON
ON
–
ON
25
ON
ON
–
–
26
ON
ON
–
ON
27
ON
ON
–
–
28
ON
ON
ON
ON
29
ON
ON
ON
–
30
ON
ON
ON
ON
31
ON
ON
ON
SV6
7L
1
2
3
4
5
6
OFF POSITION
INDICATOR
2-6 SETS HOUSE ID
5800RL DIP Switch
5800RF-003-V0
165 Eileen Way, Syosset, NY 11791
Copyright © 2000 PITTWAY CORPORATION
SPECIFICATIONS
Dimensions:
5
6
2-3/4" W x 4-15/16" H x 1-1/16" D.
(70mm x 125mm x 27mm)
–
–
–
ON
Voltage:
ON
–
12VDC 100mA OR
ON
ON
–
–
9VAC, 15VA (use ADEMCO 1332 or equivalent)
–
ON
Current:
ON
–
ON
ON
60mA
–
–
Relay:
–
ON
ON
–
Two relays, each with choice of normally open or normally closed
ON
ON
operation.
–
–
–
ON
Contact Ratings: 2 Amps at 28VDC.
ON
–
Operating Temperature:
ON
ON
0 - 50°C / 32 - 122°F
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT
This equipment has been tested to FCC requirements and has been found
acceptable for use.
information:
This equipment generates and uses radio frequency energy and if not installed
and used properly, that is, in strict accordance with the manufacturer's
instructions, may cause interference to radio and television reception. It has
been type tested and found to comply with the limits for a Class B computing
device in accordance with the specifications in Part 15 of FCC Rules, which
are designed to provide reasonable protection against such interference in a
residential installation. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
•If using an indoor antenna, have a quality outdoor antenna installed.
•Reorient the receiving antenna until interference is reduced or eliminated.
•Move the radio or television receiver away from the receiver/control.
•Move the antenna leads away from any wire runs to the receiver/control.
•Plug the receiver/control into a different outlet so that it and the radio or
television receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced
radio/television technician for additional suggestions. The user or installer
may find the following booklet prepared by the Federal Communications
Commission helpful: "Interference Handbook"
This booklet is available under Stock No. 004-000-00450-7 from the U.S.
Government Printing Office, Washington, DC 20402.
The user shall not make any changes or modifications to the equipment unless
authorized by the Installation Instructions or User's Manual. Unauthorized
changes or modifications could void the user's authority to operate the
equipment.
See the control's Installation Instructions for limitations of this system
The FCC requires the following statement for your
and warranty information.
Advertisement
