Summary of Contents for Panjing3D PJII
- Page 1 The User Manual of PJII 3D Printer Please read this user manual carefully before using this product.
- Page 2 Thank you for using the 3D printing products of Panjing 3D Technology Co., Ltd. The design concept of PJII 3D Printer is elegance and versatility. Even if you have never used 3D printer, you are able to create your favorite model easily only with a touch screen.
- Page 3 PJII Printer Body 1. Left Nozzle 2. Printing Plate 3. Display Screen 4. Right Nozzle 5. Power On/Off Button 6. SD Card 7. USB Interface 8. Filament Spool Mounting Hole 9. Power Adapter Hole 10. Power Interface 11.The Filament Feeding Hole...
- Page 4 Printer Platform Leveling 1. Plug in the power cord and turn on the power switch. Then press and hold Power On button for 3 seconds till starting up. 2. Click Tools option on the display screen. 3. Select and click the Leveling option on the display screen, and click NEXT.
- Page 5 The Installation and Replacement of Filament Please properly install the Accessory—Filament spool Axis, and correctly install the Filament Spool on the Filament Spool Axis. (Pay attention to the direction of filaments, and please be sure not to install it backwards! Also please make sure there is no knot or lag in the filament.)
- Page 6 Pull out the filament from the filament spool, and cut out a bevel gap at the top, then lead the end of the filament to the motor in accordance with the direction of arrow in the following Figure. Press down the Filament Feeding Press Block, and introduce the filament into the extruder.
- Page 7 Preheating 1. After startup, click Tools option on the display screen. 2. Select and click Filament. 3. Select Install Filament Nozzle, click the Temperature Display, which indicates it starts heating when it turns red. 4. Wait for 1-2 minutes till the temperature of nozzle reaches the preset temperature. Click Install Filament Feeding option.
- Page 8 5. Clicking on STOP when the filament is extruded out of the nozzle. Note: If there are filaments in other colors being extruded at the beginning of filament feeding, they are the remaining filaments inside the nozzle during the factory test. It belongs to the normal condition.
- Page 9 Installation of ChiTuSlicer Software Ⅰ Open the installation file of ChiTuSlicer in SD card, and click Install. Ⅱ Enter the software installation interface and click Next. Ⅲ Select the installation location, and click on Install. Ⅳ After the software installation is finished, click on Close.
- Page 10 Basic introduction of ChiTuSlicer software Open the Choose Machine Model option of ChiTuSlicer software to select the model settings. Set up the parameters according to the corresponding machine model data in the machine model parameter file in SD. (This step is not needed when WiFi online)
- Page 11 Click and open File icon. Open the designated STL file; after we choose the designated file, our chosen file model will display on the right side of software; Click on the model, Remove Model and other options will display.
- Page 12 Right-click on the model, then three icons will appear at the left corner. Select “Rotate” to rotate the model; Select “Scale”, the model can be scaled; Select “Mirror” to mirror the model; ChiTuSlicer software offers a variety of advanced observation methods. These methods are hidden in the button at the upper-right corner.
- Page 13 Currently, we are using the default Normal mode. You can also select Overhang mode, Transparent mode, X-Ray mode, and Layers mode. Under the Overhang mode, the overhanging parts of 3D model will be shown in red. In this manner, users can be allowed to easily observe the problematic parts of the 3D printing model.
- Page 14 In the Figure above, we are observing the condition of the 58th floor. As shown in Figure, the outermost part in red represents the shell of model. The following green part remains one section of the shell, but it is not directly exposed. The middle part in yellow is filling, which is used to constitute the central part of solid object.
- Page 15 The fast advancing process of the progress bar just now is the working process of ChiTuSlicer software slicer. When the slicer operating is finished, 3D printing time (2 hours and 37 minutes), required length of the plastic filament (9.08 meter) and gram (27g) are all calculated.
-
Page 16: Printing Quality
Printing quality Slice thickness indicates the height of each layer. This setting affects printing speed most directly. It is obviously that the smaller the slice thickness is, the longer the printing time is, and relatively good printing accuracy can be obtained. Wall thickness is thickness of the plastic casing generated around it by a solid 3D model in the 3D printing process. - Page 17 Support Firstly, as for the support types, there are choices among no support, extending to the platform support and all overhanging support. Extending to platform support is the type of support which is only set to the model part that adheres to the platform. All overhanging support refers to establishing support for suspended parts inside the model.
- Page 18 Fallback It can set speed and distance of fallback to reduce wiredrawing of printing model and enhance the smoothness of surface of printing model. Double nozzles switching fallback is to control the leakage in double-nozzle printing. Printing quality It has something to do with the bar of printing quality in the Basic Settings, but generally it does not need to be modified.
- Page 19 nozzles, better results can be obtained. It is usually appropriate that these maintain the default values. Speed is used to specify the operating speed of printer at various stages of 3D printing. Refrigeration is used to control parameters of the cooling fan. It is rarely seen that these two bars need to be modified, so it is appropriate to maintain the default value.
- Page 20 Wireless WIFI Connection WiFi connection computer need to have the wireless network adapter capability, and it should be online with the printer via the wireless router. The printer and computer must be connected to the same wireless router. (SD card must be inserted into the printer at the time of WiFi connection) Wireless WIFI connection method 1: The direct connection to hotspot, one-to-one Attention: For direct connection to hotspot, the computer is unable to connect to the...
- Page 21 3. Open the ChiTuSlicer software. It indicates the successful connection if the name and IP address of the printer are displayed at the upper-right corner of the software. (If you do not see the printer icon, it indicates that it does not connected to the printer. Please check whether the wireless network of computer is properly connected to the printer.
- Page 22 2. Enter hotspot password of the access router, click on Configure and Save. 3. Put the just resulting gcode in SD card, plug the motherboard and start printing, check it after it is completed.
- Page 23 4. Restart the ChiTuSlicer software, you can see the scanned device, select the device. After loading STL model file which needs to be printed, properly adjust the printing parameters and select Send File option and left-click on it to send the file, or right-click it, and finish sending Gcode, then print directly.
- Page 24 Repeatedly examine the hotspot and password of the router. A large proportion of people cannot properly connect because of the error of hotspot and password After-sales Service Guarantee “Quality Assurance”: The strict processing standards of accessories and assembly testing procedures of 3D printers of Panjing 3D Technology Co., Ltd. ensure that each product is a qualified product with superior quality.
- Page 25 “Return and Exchange Guidance”: ⅠBasic Requirements for Return and Exchange. Please guarantee the integrity of product packaging, product accessories and guarantee card. There are no man-made damages or obvious and non-removable stains on the appearance. There is no man-made modification towards the machine structure and the motherboard firmware.
- Page 26 (7) The malfunction or damage caused by force majeure. Such as a fire or earthquake. Warm Tips (Ⅰ) Please do not touch the printing head since its temperature is too high. (Ⅱ) Please use the dedicated supplies of our company, the application of other supplies will cause nozzles to be easily blocked.
- Page 27 there are no proper tools, please do not dissemble it without permission; if you really need the disassembly, please contact us. f) After a period of operation (a month later), you need to apply lubricating grease on the motion section. (Ⅵ) Precautions for printing materials: a) During printing, please ensure that the supplies is able to rotate smoothly.
- Page 28 Accessory List Model Shovel Filament Coil SD Card Power Cord USB Data Wire Contact: Tell: 0579-89280897; Email: zj@panjing3d.com Address: No. 33, Xita Road 3, Yongkang City, Jinhua Municipality, Zhejiang Province Parameter Table: Printer Model PJII-180 PJII-540 Number of Nozzles Basis Technology Display Screen 3.5 inches touch screen...
- Page 29 Model Format Operating System WINDOWS7-8 WINDOWS7-8 Printer External 500*450*470mm 590*510*780mm Dimensions Net Weight 24kg 50kg Input Voltage and 100-240V 50~60HZ 100-240V 50~60HZ Power 300W 300W Federal Communications Commission (FCC) Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 30 This device complies with Industry Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interfe rence that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radi o exempts de licence.