Download
Share
Print this page
Focus 4010 Instruction Manual
  1. Manuals
  2. Brands
  3. Focus Manuals
  4. Furnace
  5. 4010
  6. Instruction manual

Focus 4010 Instruction Manual

Porcelain firing furnace
Hide thumbs

Advertisement

Quick Links

INSTRUCTION MANUAL
Focus 4010\ Focus 4010 HT porcelain firing furnace

Advertisement

loading
Need help?

Need help?

Do you have a question about the 4010 and is the answer not in the manual?

Questions and answers

Summary of Contents for Focus 4010

  • Page 1 INSTRUCTION MANUAL Focus 4010\ Focus 4010 HT porcelain firing furnace...
  • Page 2 ATTENTION! Do not pull out the furnace by its support in order to avoid damages. FOCUS 4010/HT Dental Porcelain Furnace Page 2 Manual version 4.2.2013...
  • Page 3 2) Lower the table by inserting the crank supplied, into the hexagonal screw located at the back of the furnace. Caution! Caution! Caution! Risk or Danger Risk of electric shock surface! Refer to documentation. FOCUS 4010/HT Dental Porcelain Furnace Page 3 Manual version 4.2.2013...

  • Page 4: Table Of Contents

    INDEX - CHAPTER Furnace Installation General Description Initial Operation The Firing Cycle Supplementary Features Calibration Diagnostics mode and Furnace data Programs Technical support FOCUS 4010/HT Dental Porcelain Furnace Page 4 Manual version 4.2.2013...
  • Page 5  Placing the furnace according to the above mentioned instruction will guarantee the proper temperature stabilizing, heating and cooling. FOCUS 4010/HT Dental Porcelain Furnace Page 5 Manual version 4.2.2013...

  • Page 6: Initial Operation

    Press the ON/OFF key on the front panel. The furnace is now in Idle mode.  Press [STOP/LIFT] platform will descend automatically.  Place the ceramic table on the platform!!!  The furnace is now ready for the Initial Operation Procedure. FOCUS 4010/HT Dental Porcelain Furnace Page 6 Manual version 4.2.2013...

  • Page 7: General Description

     Temporarily “freezes” the firing cycle. Programming keys: PROG -  Sets the furnace into the mode for program selection. (PROGRAM) ARROWS keys Closing and opening the table and toggle between the FOCUS 4010/HT Dental Porcelain Furnace Page 7 Manual version 4.2.2013...
  • Page 8  While a selection is incorrect the field will be displayed in Red with Parameters Limits.   In The Display mode all the status and parameters will appears in reel time. FOCUS 4010/HT Dental Porcelain Furnace Page 8 Manual version 4.2.2013...
  • Page 9  A single tone sounds, when a key is pressed or when the furnace is in the "HOLD" mode.  A double tone sounds when there is an incorrect key selection or choice of data.  A five double-tone sounds at the end of a firing cycle. FOCUS 4010/HT Dental Porcelain Furnace Page 9 Manual version 4.2.2013...

  • Page 10: Power Switch

    Only after completing this procedure is the furnace ready for use. Power Switch : To start the furnace press the power switch located on the rear panel to the ON position, the furnace is now in the Stand -by Mode. FOCUS 4010/HT Dental Porcelain Furnace Page 10 Manual version 4.2.2013...

  • Page 11: Programs

    Using the number keys enter any number from 0-249 or scroll with the arrows to the chosen program. Press the "ENTER" key. POINTS TO NOTE  When editing is required press menu button and press option 1- edit program. FOCUS 4010/HT Dental Porcelain Furnace Page 11 Manual version 4.2.2013...
  • Page 12 Press the “ENTER” key when finished to introduce or to change all the required parameters. To run the cycle go back to the main screen by pressing the menu button FOCUS 4010/HT Dental Porcelain Furnace Page 12 Manual version 4.2.2013...
  • Page 13 6. Press the keys [7], [2], [0]. 7. Press the key [ENTER] or arrow key again. FOCUS 4010/HT Dental Porcelain Furnace Page 13 Manual version 4.2.2013...
  • Page 14 0 to 30 minutes (specified in minutes and seconds). 0 to 4:30 H in the HT Programs 1. Intermediate delay when FINAL TEMP is higher than HIGH TEMP. Comments Parameter FINAL TEMP FOCUS 4010/HT Dental Porcelain Furnace Page 14 Manual version 4.2.2013...
  • Page 15  In the event of an error, the warning tone will sound by pressing START and the firing cycle will not start. The erroneous parameter will blink indicating the source of the problem. This parameter isn’t logical or it is out of the permitted limits. FOCUS 4010/HT Dental Porcelain Furnace Page 15 Manual version 4.2.2013...
  • Page 16 By pressing the arrow up you can modified the position of the table within a cycle or close the table at any working stage of the furnace . FOCUS 4010/HT Dental Porcelain Furnace Page 16 Manual version 4.2.2013...
  • Page 17 Should you wish to cancel the program in the middle of a firing cycle, press the [STOP/LIFT] key. The platform is lowered and the furnace remains in the selected program mode. FOCUS 4010/HT Dental Porcelain Furnace Page 17 Manual version 4.2.2013...

  • Page 18: Supplementary Features

    These changes are temporary and do not effect on the pre-programmed data in the cycle. In order to change the parameters during cycle the following steps are required: Press “HOLD” key –Press Menu+ Edit current program. FOCUS 4010/HT Dental Porcelain Furnace Page 18 Manual version 4.2.2013...
  • Page 19 If you wish to cancel a program in the middle of a firing cycle, press the [STOP/LIFT] key. The platform is lowered and the furnace remains in the selected program mode FOCUS 4010/HT Dental Porcelain Furnace Page 19 Manual version 4.2.2013...
  • Page 20 All the programs can be modified and adapted to all kind of manufacturer requests. The Focus Ht is one of the only furnaces that allow you to sintering Alumina as well as to fire the conventional ceramic in the same furnace.
  • Page 21 FOCUS 4010/HT Dental Porcelain Furnace Page 21 Manual version 4.2.2013...
  • Page 22  In the event of an error, the warning tone will sound by pressing START and the firing cycle will not start. The erroneous parameter will blink indicating the source of the problem. This parameter isn’t logical or it is out of the permitted limits. FOCUS 4010/HT Dental Porcelain Furnace Page 22 Manual version 4.2.2013...

  • Page 23: Calibration

    In order to return to the basic, factory made calibration perform the following: Enter to the calibration adjustment mode again and cancel the stored value Calibration will be restore FOCUS 4010/HT Dental Porcelain Furnace Page 23 Manual version 4.2.2013...
  • Page 24  Note we highly recommended you to exchange your muffle after 3500 Working hours above 500 degrees- your furnace have a counter that show you all the information" hours meter" FOCUS 4010/HT Dental Porcelain Furnace Page 24 Manual version 4.2.2013...
  • Page 25 8. Programs Start temp Up time Dry time Heat rate High temp Temp delay Final temp Final delay Cool time Vacuum start Vacuum end Vacuum delay Vacuum level FOCUS 4010/HT Dental Porcelain Furnace Page 25 Manual version 4.2.2013...
  • Page 26 A. Technical Specifications Thank you for choosing the Focus 4010 ceramic furnace for your laboratory needs. For any questions or additional support, please contact us and we will look forward to assisting you. Electrotherm Marketing – ShenPaz Technologies 5 HaTasia Street, Ramat Gabriel Industrial Park...

This manual is also suitable for:

4010 ht