HIOS CLT-100 Operation Manuals

for Electric Screwdrivers
Power Pack
Operation Manual
(August 2017) No. ET-A018 17C
HIOS Inc.
1-16-5 Akiyama, Matsudo City, Chiba Pref., Japan
TEL: 81-47-392-2001 FAX: 81-47-392-7773
Please read carefully the operating instructions for the electric
screwdriver and take care to use it properly.
■ Warning
Read and understand the following cautions to use the HIOS electric
screwdriver, exclusive power supply, etc. safely and properly. Failure to
follow all the cautions listed below may result in electric shock, fire and/
or serious personal injury.
1. Use the equipment with the indicated proper voltage and always connect the
equipment to ground while in use.
2. For safety, only use the equipment with a commercial power supply equipped
with a short-circuit breaker or safety breaker.
3. If a short-circuit breaker or other circuit breaker trips, stop operation
immediately, disconnect the power cord, and consult a HIOS representative
for repair.
4. Do not use the equipment with wet hands. This could cause an electric
shock.
5. Do not put the equipment near high-voltage/high-amperage machinery.
6. Do not use the equipment in or near a combustible gas, liquid or powder.
7. Do not use the equipment where static electricity (sparking) may occur.
8. Do not use the equipment with anything except a HIOS electric screwdriver.
HIOS can accept no responsibility for problems that occur if a power supply
not made by HIOS is used with a HIOS electric screwdriver.
9. Do not disassemble or modify the equipment.
10. When the equipment is not being used, turn off the power switch and
disconnect the power cord from the outlet.
11. If the equipment overheats or a circuit breaker trips, stop operation
immediately and consult a HIOS representative for repair.
12. Do not abuse the cord. Never drag the power supply by its screwdriver cord
or power cord. When disconnecting the power cord, hold and pull the plug.
13. Do not bring oil-based products or sharp edges near the cords.
14. Only use the equipment in locations with suitable humidity and temperature,
which have no smoke, dust, corrosive gases, etc.
15. Only use the equipment on a stable flat surface. Do not stack the equipment
with other objects.
16. Do not put anything on the power supply. This could cause heating.
17. Do not drop or apply strong impacts to the equipment. This could damage the
structure and contents of the equipment. Always check that the equipment
has no damage before use.
18. Keep out of reach of children during use and during storage.
19. Store the equipment in a stable position in a location with suitable
temperature and humidity.
■ HIOS Screwdrivers Run from Power Packs
Power pack HIOS electric screwdrivers for use with
Number
model
CL-2000, CL-3000, CL-4000,
CL-6000, CL-6500
CLT-100 For two drivers
SS-2000, SS-3000, SS-4000, SS-6500
α
-4500,
Up to 20
CL-2000, CL-3000, CL-4000,
SS-2000, SS-3000, SS-4000
Up to 10
MC-70L For many drivers
CL-6000, CL-6500, CL-7000,
SS-6500, SS-7000, α-4500, α-5000
Up to 5
α-6500
CLT-75 For one drivers For CL-9000
CLT-75AF For one drivers For CL-9000

■ Specifications

CLT-100 MC-70L
Model Name
AC100V/120V/220-240V
Primary Input
±5% AC100V ±5% (50/60 Hz)
Power Source
(50/60 Hz)
Secondary
HI, LOW HI, LOW
Output Voltage
Dimensions (mm)
182×145×132 320×220×153
(W) × (D) × (H)
Weight 4 kg
Cord Length 1.8 m (inlet cord with ground wire)
Trunk-line wire 20 m 1
piece (Black & Red)
Branch wire 0.5 m 10
Accessories –
(Black & Red)
U-Element 20 pieces
(see reverse side)

■ Replacing a Fuse

The LED will not light when the fuse burns
out. If the LED doesn't go on after the fuse is
replaced, the power cord may be damaged.
In this case, discontinue use immediately and
notify a HIOS service agent.
■ MC-70L and Control Box Combinations
HIOS power packs
α
-5000
● Only one driver can be connected to the model CB-105 control box.
● Connect the control box between the power pack and the screwdriver.
■ How to Wire the MC-70L Power Pack
There are two plus-minus pairs of terminals on the back of the power
pack's case for connection of the trunk-line wires.
Caution
1. When connecting the trunk-line wire, be sure the red wire goes to
the plus terminal and the black wire to the minus terminal.
CLT-75
2. Use no more than the 20 meters of trunk-line wiring provided. A
CLT-75AF
longer lead would result in delivery of insufficient voltage that can
cause driver malfunction.
Connecting procedure
HI only
1. Use U-Element to connect the trunk-line wire to the control box.
Allow a suitable amount of trunk-line wire, then connect a female
182×220×133
terminals of branch wire to a male terminals of CB-105, making sure
both wires are the same color.
12 kg 6 kg
2. Connect the driver's power cord to the control box output connector.
It is recommended that the U-Element (included with the power unit) be
used to attach a branch wire to the main wire.
pieces –
1. Holding the slot at the bottom of the element open, push the trunk-line wire into the
groove.
2. Insert the cut area of the branch wire through the upper hole from the right and push it
in all the way to the opposite end.
3. Use pliers to forcefully push U-Element flat with plastic body.
4. Snap on the insulation cover.
spare fuse