Icom SR-VPN1 Connection Manual

CONNECTION GUIDE
VPN ROUTER
SR-VPN1
Step 1 System Requirements
D Supplied Accessories
• Power adapter ............ 1
• Cushion sheet ............ 1
• Ferrite EMI filter ............ 1
• Precautions guide
• "Setting the interface language and the Time Zone" leaflet
• Connection Guide (This guide)
About this Connection Guide:
This Connection Guide explains the basic operation for the
SR-VPN1. Access our website to download the instruction
manual.
Icom website http://www.icom.co.jp/world/
Step 2 Panel description
D About the status indicator
Front Panel
[WAN] （1/2） LED
[PWR] LED [VPN] LED [BACKUP] LED
<UPDATE> Button [MSG] LED [LAN] LED [PPP] LED [USB] Port
（USB2.0）
(See the precautions guide for more details on the <INIT> and <UPDATE> buttons.)
Status PWR MSG WAN (1/2)
(Online Update)
WAN connected
Green ON A firmware update is
(1000BASE-T)
ready
Lit
WAN connected
Accessing the USB
Orange Booting (10BASE-T/
flash drive
100BASE-TX)
(Online Update) WAN is communicating
Green —
Firmware downloading (1000BASE-T)
Blinking
Initialization in
WAN is communicating
progress/
Orange — (10BASE-T/
<INIT> button
100BASE-TX)
Green/Orange
Not Lit OFF — Not connected
*1 When 1000BASE-T/10BASE-T/100BASE-TX are mixed, the [LAN] LED lights in orange.
*2 The data communication status for each [LAN] port can be checked with the [LAN] LED on the rear panel.
Read the "PRECAUTIONS" leaflet first, if you have not done so.
Thank you for purchasing this Icom product. The SR-VPN1
is designed and built with Icom's IP network
vpn router
technology. We hope you agree with Icom's philosophy of
"technology first." Many hours of research and develop-
ment went into the design of your SR-VPN1.
D Other requirements
• PC
• Ground wire
• LAN cable
NOTE:
• Adobe Reader is required on your PC in order to display the
® ®
downloaded instruction manual. (PDF File)
• If your PC does not have Adobe Reader , please download
® ®
it from the Adobe website.
®
Rear Panel
[CONSOLE] Port [WAN](1/2) Port Ground terminal
(RJ-11) (RJ-45)
[LAN](1 to 4) Port
<INIT> Button DC Jack
(RJ-45)
• The [WAN1] and [WAN2] ports on the setting screen point the
[WAN] and [WAN2] ports on the rear panel.
LAN* 1 * 2 VPN PPP BACKUP
LAN connected IPsec connected PPP connected
Backup line is
(1000BASE-T) (More than 1 (More than 1
communicating.
(More than 1 connection) connection) connection)
LAN connected
(10BASE-T/
— — —
100BASE-TX)
(More than 1 connection)
— — — —
— — — —
Not connected — — —
Step 3 Automatic setting data load with a USB flash drive
The setting data or firmware can be automatically loaded
into the SR-VPN1 from a USB flash drive.
It is useful to recover the configuration or to update the
firmware.
• The USB flash drive is not supplied. Purchase separately.
• See the SR-VPN1 instruction manual for details.
Turn OFF the SR-VPN1's power
by disconnecting the power adapter,
and then insert the USB flash
drive securely. Then, turn ON the power again by
connecting the power adapter.
Step 4 Connecting and turning the power ON
Follow the steps q to y to connect the devices.
• When connecting in the factory default condition, the connected network must be disconnected.
• If [LAN] does not light, check the LAN cable and try again.
y
Verify the LEDs light
When the [LAN] LEDs on the rear do not light, verify
that the LAN cable is securely connected.
Status indicator:
q w
Lit: LAN connected
Blinking: LAN data communicating
q Green: 1000BASE-T
w Orange: 10BASE-T/100BASE-TX
SR-VPN1
（Default ： 192.168.0.1)
Connect
e
the cables
LAN cable*
(Purchase separately）
*Category 5e or higher
t
Start the PC
PC
R WARNING!
To prevent electrical shock, television interference (TVI),
broadcast interference (BCI) and other problems, ground the
SR-VPN1 through the ground terminal.
NEVER connect the ground terminal to a gas or electric pipe.
This may result in an electrical shock or cause a fire.
About the USB flash drive
• A USB flash drive such as one with biometric authentication,
or one with password protection is not supported.
• Turn OFF the SR-VPN1's power before inserting or
removing the USB flash drive, to prevent data corruption.
• Either one of the USB slots accepts the USB flash drive, but
insert only one USB flash drive at a time.
• Insert the USB flash drive securely.
• NEVER remove the USB flash drive or turn OFF the
SR-VPN1's power, while transferring data. It will cause data
corruption, or damage the USB flash drive.
• After the firmware updating is finished, check the firmware
version on the setting screen to verify that the update was
correctly done.
• When importing setting data from the USB flash drive to
the SR-VPN1, the originally programmed setting data is
automatically saved as "bakdata.sav" in the USB flash drive,
as a backup.
q
Attach the cushions w
Attach the ferrite EMI filter
Power cable
Ferrite EMI
filter
Wrap the cable once
Cushion Sheet
around the filter.
r Connect the
power supply
The [PWR] LED on the
front panel lights.
AC wall socket
Power adapter
Ground wire Ground terminal
Ferrite EMI filter
(Purchase separately)
IP address for PC
The SR-VPN1's IP address is set to "192.168.0.1", and DHCP
server to "Enable" as default. Therefore, set the connecting PC
for the IP address to automatically access.
See the PC's instruction manual for the IP address setting
details.
Continued on the back side.