nodon MSP-2-1-11 User Manual

USER GUIDE
Micro Smart Plug
METERING
Micro Smart Plug Type E Micro Smart Plug Schuko
Reference: MSP-2-1-01 Reference: MSP-2-1-11
Power supply: 230V AC ~ 50Hz
Self-consumption <1W
Max. power: 1840W continuous (Resistive load)
Metering of Instantaneous Power (W) and accumulated Energy (Wh)
Center radio frequency : 868.3 MHz
Occupied frequency band : 868.0 to 868.6 Mhz
RF power Max : +3dBm
Range up to: 60m outdoor / 30m indoor
Operational temperature: 0°C / 35°C
IP20
Memory capacity : 24 emitters
EEP (Profil EnOcean ): D2-01-0E
®
Dimensions: 46mm (Diameter) x 74mm (H)
Weight: 67g
Warranty: 2 years
The NodOn Micro Smart Plug + Metering allows to control (Power
®
ON or Power OFF) an electrical appliance plugged on it: bedside
lamp, electrical heater, coffee machine, etc. Once set up (see the
set up procedures below), the NodOn Micro Smart Plug can be
®
controlled by different EnOcean compliant emitters (wall switch,
®
remote controller, sensor, window handle, card switch, etc.).
Check the compliant emitters list below.
Thanks to build-in Metering features, the Micro Smart Plug can
meter Instantaneous Power (W) and Accumulated Energy (Wh),
between two buffer's reset.
INSTALLATION
Plug the NodOn Micro Smart Plug on your power outlet.
1 ®
Plug the electrical appliance, you want to control, on the NodOn
2
Micro Smart Plug.
3 The Micro Smart Plug allows to switch ON (Power ON) or switch
OFF (Power OFF) the electrical appliance you want to control.
Switching ON or OFF can be done through the Micro Smart Plug
local button, or any kind of emitter paired to the Micro Smart Plug
(check the next steps of the user guide).
If the electrical appliance (ex.: bedside lamp) has an ON/OFF button, make sure it's positioned
on "ON", in order that the power ON of the appliance by the Micro Smart Plug will switch ON
the lamp.
MICRO SMART PLUG MODES
LOCAL CONTROL
<1s
<1s
The Micro Smart Plug can be switched ON or OFF locally, through
a short press on the local button. By default, the Micro Smart Plug
is switched ON when the LED is green, OFF when the LED is OFF.
PAIRING MODE
2s
{Shining}
Press on the Micro Smart Plug button during 2 seconds until the
LED becomes red. Release the button.
The LED will then glow in red. The Micro Smart Plug is in "Pairing
mode"
To pair an emitter, follow the "Pairing procedures". To confirm that
the pairing is OK, the LED will blink in green.
If the LED blinks orange during "Pairing mode", it means that the
memory of the Micro Smart Plug is full, or that no emitter has been
paired during the process.
In case of full memory, please unpair an emitter before being able
to pair a new one.
Note: The NodOn Micro Smart Plug supports the EnOcean Remote Commissioning features.
® ®
It can be put wirelessly into « Pairing mode » through a compatible home automation gateway.
FACTORY RESET
>5s
To perform a factory reset, press on the Micro Smart Plug button
during 5 seconds until the LED becomes orange. Release the
button, the LED will blink red/green.
The factory reset will remove all the emitters from the Micro Smart
Plug memory, and set all the parameters of the Micro Smart Plug
to default value.
Factory Reset clears Energy (Wh) buffer as well.
PAIRING PROCEDURES
Wall Switch, Remote Controller, etc.
EnOcean Type "Rocker Switch" (EEP: F6-02-01)
®
To pair this type of emitter to the Micro Smart Plug:
Put the Micro Smart Plug in "Pairing mode".
1
®
Press any button of the emitter. The button pressed during the
2
pairing process is the button which will switch ON the Micro Smart
Plug. The opposite button will switch OFF the Micro Smart Plug.
The other buttons of the emitter will not be able to control the
Micro Smart Plug.
Pairing Mode
Button paired during Button pressed on
"Pairing mode" the emitter
I
O
P
ON
M
To unpair this emitter:
Put the Micro Smart Plug in "Pairing mode".
1
Press any button of the emitter
2
OFF
The emitter can't control the Micro Smart Plug anymore.
Key Card Activated Switch
EnOcean ® Type "Key Card Activated Switch" (EEP: F6-04-01)
To pair this type of emitter to the Micro Smart Plug:
Put the Micro Smart Plug in "Pairing mode".
1
Insert or remove the card from the reader. The movement of
2
the card done during the pairing process is the movement which
will switch ON the Micro Smart Plug. The opposite movement will
switch OFF the Micro Smart Plug
To initialize the Micro Smart Plug, insert and remove (or remove
3
and insert) the card.
Pairing Mode
Movement done during
Card position
« Pairing mode »
INSERTED
INSERT
REMOVED
REMOVED
REMOVE
INSERTED
To unpair this emitter:
Put the Micro Smart Plug in "Pairing mode".
1
Insert or remove the card.
2
The emitter can't control the Micro Smart Plug anymore.
EnOcean Type "Window Handle" (EEP: F6-10-00)
®
{Shining}
To pair this type of emitter to the Micro Smart Plug:
Put the Micro Smart Plug in "Pairing mode".
1
Make the relevant movement with the handle according to your
2
need. Check below table.
Note: "Bottom hung" and "Open" position are identically considered
Pairing Mode
Open
Bottom hung
Movement done during
« Pairing mode »
Open Open
Bottom hung Bottom hung
OPEN or BOTTOM HUNG
Close
To unpair this emitter
Put the Micro Smart Plug in "pairing mode".
1
Make any kind of movement with the handle.
2
The emitter can't control the Micro Smart Plug anymore.
EnOcean ® Type "Magnetic Contact" (EEP: D5-00-01)
To pair this type of emitter to the Micro Smart Plug:
Put the Micro Smart Plug in "Pairing mode".
1
Press on the "learning" button of the opening sensor. The
2
Usage
position (close or far) of the magnet from the sensor when the
Micro Smart Plug
"learning" button is pressed is the position which will switch ON
state
the Micro Smart Plug. The opposite position will switch OFF the
I ON
Micro Smart Plug. Check the table below.
O OFF
O ON
I OFF Pairing Mode
P ON
Magnet position when the
learning
M OFF
« Learning » button is
M ON
P OFF
far
close
To unpair this emitter:
Put the Micro Smart Plug in "pairing mode".
1
Press on the "learning" button
2
The emitter can't control the Micro Smart Plug anymore.
EnOcean ® Type "PIR Sensor" (EEP: A5-07-01 / A5-07-02 / A5-
07-03 / A5-08-01 / A5-08-02 / A5-08-03)
To pair this type of emitter to the Micro Smart Plug:
The status of the Micro Smart Plug (ON or OFF) chose before
1
put in "pairing mode" will be associate with a presence detection
2 Put the Micro Smart Plug in "pairing mode".
Press the "learning" button of the presence sensor.
3
When a presence is detected, the Micro Smart Plug will be in the
Usage
state (ON or OFF) defined at step 1.
When no presence is detected, the Micro Smart Plug will be in the
Micro Smart Plug state
opposite state. Check the table below.
ON
OFF
ON Pairing Mode
OFF
Micro Smart Plug state
before "pairing mode"
ON
OFF
To unpair this emitter:
Put the Micro Smart Plug in "pairing mode".
1
Press on the "learning" button.
2
The emitter can't control the Micro Smart Plug anymore.
Window Handle
Usage
Micro Smart Plug
Handle position
state
OPENED or
ON
BOTTOM HUNG
CLOSED OFF
CLOSED ON
CLOSE
OPENED or
OFF
BOTTOM HUNG
Opening sensor
Usage
Micro Smart Plug
Magnet position
state
pressed
CLOSE ON
CLOSE
FAR OFF
FAR ON
FAR
CLOSE OFF
Motion sensor
Usage
Micro Smart Plug
Sensor status
state
PRESENCE ON
NO PRESENCE OFF
NO PRESENCE ON
PRESENCE OFF