Warmtech T510 Installation Manual

WARMTEC T510 Weekly Programming Thermostat with LCD Screen
T510. Weekly Programming Thermostat with LCD Screen
Weekly circulation, it is possible to set 6 periods called events each day with
different temperatures, also you can select "manual mode" or "temporary
control mode" according to your individual requirements. The thermostat is
recommended for the control of electric heating devices or on/off valve actuator
used in water-based heating systems.
Selection Table:
Model Current
Built-in & floor sensor, floor limit sensor, period
T510 16A
programming
T510i 16A A pair of contacts for potential- free output
Technical data:
Voltage : AC230V (AC110V/AC24V available)
Power consumption : 2W
Setting range : 5℃~90℃
Limitation range : 5℃~99℃ (factory setting: 35℃)
:0.5℃~10℃ (factory setting: ±1℃)
Switching differential
Ambient temperature : -5℃~50℃
Protective housing : IP20
Housing material : self-extinguishing PC
Daily use of the thermostat
1） on/off " "
2） In the manual mode，press "
3） Press" " or" " to increase or decrease pre-set temperature.
4） Press" " and" "and hold for 5 seconds at the same time to adjust
time. Press " " to choose object to adjust; Press"
increase or decrease your set values; Press "
5） Press the " " key to select manual mode or clock-controlled program
mode.
6） It displays the time or the pre-set temperature alternately, and it displays
the measured temperature directly.
7） When you press " " and"
the thermostat will be locked/unlocked. When it is locked, no operation
can be carried out until it is unlocked.
Display symbols：
Manual mode
Period control mode
Heating
Getting up, the first period
Out in the morning, the second period
Going home at noon, the third period
Out in the afternoon, the forth period
Going home in the evening, the fifth period
Sleeping at night, the sixth period
Period programming
Press " " and hold for 5s to enter the mode of Period programming.
Key Period Symbol
1
2
3
4
5
6
1
2
WARMTEC T510 Weekly Programming Thermostat with LCD Screen
Application
" or" "to make temporary control。
" or"
" to confirm and exit.
"at the same time and hold for 5 seconds,
Time
Temperature
06:00 20℃
08:00 15℃
11:30 15℃
12:30 15℃
17:00 22℃
22:00 15℃
08:00 22℃
23:00 15℃
Advanced setting (qualified person preferred)
When the thermostat is turned off, You can press"
time ,then you can enter the mode of advanced setting.
Symbol
1 ADJ
2 SEN
3. LIT
4 DIF
5 LTP
6 PRG
7 RLE
8 DLY
9 HIT
AFAC
Sensor failure:
" to
Please select the right sensor mode when operation, it will display the
"Err" symbol on screen far sensor failure, thermostat must be checked till
the fault is eliminated
Explanation of symbols:
Manual mode
Six period
Time
Week
Menu
Increase key
Dimension:
Unit: mm
Installation Manual
" and turn on it at the same
Setting or
Temperature Adjust measured temperature
calibration
Sensor mode IN: built-in sensor
OUT: floor sensor
ALL: both sensors
Limitation Adjust limitation value,
temperature
Limitation range:5℃~60℃
Switching Adjust switching differential
differential
Antifreeze Turn on/off Anti-frozen
function function
Set vacation 00: 5/2 day mode
mode 01: 6/1 day mode
02: 7 day mode
Potential- free Change the present
output and main linkage way
power output in
the
same/different
way
Delay time of Change linkage delay time
Potential- free
output
Max temperature Limitation temperature
setpoint
Reset to factory
Press" "and hold for 5s，all
settings
parameters will be reset
Decrease key
86
Installation Manual
Period mode
Antifreeze
temperature
Lock key
heating
power
NTC
43
13