Advertisement
5304
5305
5307
5308
5033
5033
5304
5305
5307
5308
and directions of use
Directions of use
1. Set the temperature and water
pressure with the singe grip mixer.
With the diverter ➊ you can
switch between overhead shower
(➊:1), hand shower (➊:2) and
body sprays (➊:3).
2. The overhead lighting is switched
on and off using the button above
the diverter.
Maintenance
1. Cleaning the shower cabin should be done using a soft
cloth with cleaning agent. In order not to damage the shiny
surface, pls do not use cleaning agents containing polish
grains, acetone or ammoniac.
2. Lime deposits can be solved using a lime solvent.
3. Drains and spouts should be cleaned regularly to prevent
stops.
4. Polish chromed parts with care.
Package content
The shower cabin is delivered in two or three boxes, containing:
•
A ssembly guide
•
S hower tray
•
G lass front including 2 doors
•
2 cover strips
•
Back wall
•
Roof section
•
Assembly bag
•
H and shower with hose
Assembly preparation
1. For water supply, there are 2
flexible hoses of 1 m with R ½"
inner grooves on the back of the
shower cabin.
2. Water is drained by a 70 cm flexible
plastic pipe ➋.
3. The overhead lighting shall be
connected to a 230 V wall socket.
➊
➋
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DUSCHY 5033
Summary of Contents for DUSCHY 5033
- Page 1 ➊ 2. The overhead lighting is switched on and off using the button above the diverter. Maintenance 5305 1. Cleaning the shower cabin should be done using a soft cloth with cleaning agent. In order not to damage the shiny surface, pls do not use cleaning agents containing polish grains, acetone or ammoniac. 2. Lime deposits can be solved using a lime solvent. 3. Drains and spouts should be cleaned regularly to prevent stops. 4. Polish chromed parts with care. 5307 5033 5033 5304 Package content The shower cabin is delivered in two or three boxes, containing: 5305 5308 • A ssembly guide • S hower tray 5307 • G lass front including 2 doors • 2 cover strips •...
- Page 2 ➊ Assembly guide 1. Put the tray in the desired place ➊ and adjust the feet until the tray is level and at the desired height. Use a water level. Tighten the bolts of the feet. 2. Put a string of wet silicone ➋ on the parts of the tray that will face the back wall. Put the back wall on the tray and fasten it with screws and nuts. 3. Put a string of wet silicone where the tray will face the glass front. Put the glass front on the tray. ➋ NOTE! The arrows on the outside of the glass walls must point upwards. 4. The glass front is fitted along the round edge of the tray, with screw and nuts. ➌ 5. Attach the cover strips on the edges of the glass wall doorway. 6. Attach the detachable front piece on the tray with the velcro strips and the snap fastening. ➍ ➌ 8. Put a string of wet silicone on the top of the glass and back wall, where the roof section will face them. First screw the roof to the upper forward part of the glass front using screws and nuts. Then fasten the back part of the roof to the back wall with screws and nuts. 9. Tighten all screws that have been fitted so far. 10. Connect the hose from the overhead shower to the diverter. At- tach with a hose clip. Connect the hand shower using a washer in both ends of the hoses. 11. Connect the flexible hoses (R ½” inner grooves) to the hot and cold water pipes of the house. Red mark for hot water and blue for cold.
Need help?
Do you have a question about the 5033 and is the answer not in the manual?
Questions and answers