Adtech EN-30 Quick Start Manual

Thank you for your purchase of the Adtec
EN-30 Encoder/Modulator. This product is sold
with one or two encoder modules and with optional modulator hardware packages.
Some configurations may differ from the unit you have purchased if there is only
one encoder module installed. If you purchased this product without a modulator,
please disreguared settings noted with an astericks.
Quick View Status
For information on the core systems of the encoder,
use the down arrorw on the front panel to scroll
through these quick view menus.
Encoder Status TMR Auto Fill Encryption
ENCODING: 38.810Mb/s A/F: OFF CAS:BISS_1
TSI: 00001 SVC1: ON SVC2: OFF
Transport Stream ID Service 1 Service 2
Service1 ID Service1 Name Service1 Provider
SVC1: 00003 "AdtecHDTV1" Adtec Digital 1
SVC2: 00004 "AdtecHDTV2" Adtec Digital 2
Service2 ID Service2 Name Service2 Provider
Input 1: Resolution Frame Rate Source Mode
RES1: 1920x1080 25i INP: SDI MODE: AUTO
RES2: 720x480 59p INP: COMP MODE: SD
Input 2: Resolution Frame Rate Source Mode
Video Bit Rate CODEC Chroma
VRT1: 15000000b/s COD: MPEG2 CHR: 422
VRT2: 18242000b/s COD: H.264 CHR: 420
Video Bit Rate CODEC Chroma
Bitrate Type
Audio 1: 1 - 4
1:MU 384k 2:MU 384k 3:MU 384k 4:MU 384k
1:DD 192k 2:DD 192k 3:MU 384k 4:MU 384k
Audio 2: 1 - 4
Bitrate Type
Video1 PID Audio1 PIDs 1-4
VID: 0309 AUD:1: 0257 2: 0258 3: 0259 4: 0260
VID: 0308 AUD:1: 8180 2: 8181 3: 8182 4: 8183
Video2 PID Audio2 PIDs 1-4
RTP FEC Status Connector
TSoIP 1 - 4
1: SEND ON BUR GIGE 3: SEND OFF OFF GIGE
2: SEND ON OFF GIGE 4: OFF OFF OFF GIGE
ASI Remux Status Programs on Input
REMUX: ACTIVE PROGRAMS: 7
INPUT: 038.963Mb/s CAPACITY: 040Mb/s
Input Data Reserved Bandwith
*Modulator Status Mod FEC Power Roll O
TX: Enable 32APSK_9/10 Pwr: -30dB RO: 25%
Freq: 1291MHz DVB-S2 Sym: 15.00Ms Pilot: ON
Frequency Mode Symbol Rate Pilot
Adtec Digital US Sales +1-615-256-6619 International Sales +1-904-394-0389
EN-30
Dual DSNG Encoder / Modulator
Services
TS Mux Rate
LED Status
Auto ll
Video
Off - No Video is detected
Tables
On - Video is detected
Encode TSID
Off - Device is not encoding
ASI Mode
On - Device is encoding
AVC
ASI Remux
Off - MPEG2 module installed
<< Ch1 - Ch2 >>
On - MPEG4 (H.264) module
installed
Active
HD
Off - Video Input is SD resolution
Service Name
On - Video Input is HD resolution
Svc Provider
A1 - A4
Off - Audio mode set to OFF
Program #
On - Encoding or Passthru audio
Logical Ch #
Alarm
Off - No system alarms
Bars,Tones,ID
On - System alarm
BISS
Off - Encryption config is OFF
On - Encryption config is ON
Link
Off - No network detected
On - Connection active
Busy
Off - No network activity
On - Network traffic present
Reset:
Should you need to reset your
There are 2 di erent encoder modules available for the EN-30 and the unit
device, you can do so via the front
panel by pressing the MODE, ESCAPE
can be ordered with either or both:
and RIGHT ARROW keys
simultaneously.
Video Encode AVC
HD
A1
A2
A3
EN-30
Dual MultiCODEC
Encoder/Modulator
A3
A2
A1
Video AVC HD
Encode
www.adtecdigital.com
*RF Tx IP Tx Video
Transmit << 1 - 4 >> << Ch1 - Ch2 >>
Type Mode Input
Mode IP Tx Mode SDI Mode
Local Oscillator Tx IP Address Chroma
Uplink Freq Tx Port Video Rate
Frequency(MHz) Tx GW Address Aspect Ratio
Power(dBm) DVB per IP AFD
Spectrum Invrsn RTP GOP Type
Fec Frame FEC Mode GOP Structure
Roll O FEC L GOP Size
Pilot FEC D Fault Mode
Rate Priority FEC TOS bits Fault Resolution
Symbol Rate Type of Service
Interface Rate TTL
Carrier Mode Tx Connector
10 MHz Clock Service Select
Clock Comb. Mux Rate Mode
Multicast Rate
A4 ENCODING:20.000M A/F:ON CAS:BISS_1 ENCODING:20.000M A/F:ON CAS:BISS_1
Alarm
BISS
TSI:00001 TSI:00001 SVC1:ON SVC1:ON
Link Busy
A4
Audio PIDS VBI
Video
Audio
<< Ch1 - Ch2 >> Source
ENC1 ENC2
<< 1 - 2 >> PMT PID Closed Cap.
Surround Mode PCR PID
<< 1 - 4 >> Video PID
Input Audio 1 PID
Model Indicators:
Mode Audio 2 PID
Type Audio 3 PID
No modulator
Rate Audio 4 PID
IF/LB/10M modulator
Level Teletext PID
Sync AMOL PID
Format VITC Mode
IFB VITC PID
SDI Pair Splice Mode
SDI Clock Source Splice PID
ECC
Front Panel Menus:
SDI Audio Grp.
Use Mode Button to move
MODE
through top layer menus.
Use arrows for navigation
in submenus.
Special Keys:
Use the F2 button as a decimal.
F2
MP2 - MPEG2
MP4 - H.264
SVC2:ON SVC2:ON
Quick Start Guide
Pro le CAS System
VBI System
CAS
Select Mode Login
Save Clear SW Duration
Delete Encrypted SW Backlight
User ID 1 Network Menu
User ID 2 Time Menu
NTP Menu
Alarm
SNMP Menu
COM2
Feature Menu
Name
Firmware
Use select to enter into edit
mode and enter to
SELECT ENTER
save selection.
Units ship with the front panel
logged in by default. If you become
logged out and are prompted for a
password, use the following key
sequence for access.
Press <Select> when panel displays
'User Login -- logged out'
Press <Up arrow>
Press <Select>
Press <Enter>
Press <Right arrow>
Press <Enter>
2014 Adtec Digital