Related Manuals for Atlantic PS3900
Summary of Contents for Atlantic PS3900
- Page 1 Instruction Manual Skimmer Part No. PS3900 FilterFalls Part No. BF1600 Pump Vault Part No. PV1700 1-877-80-PONDS FastFalls Part No. SP1600 www.atlanticwatergardens.com...
-
Page 2: Table Of Contents
AF1000 AutoFill Kit Page 16 Skimmer Overflow Page 16 This manual contains basic construction techniques and installation instructions for Atlantic Oasis Series Pond and Pond-Free products. For more in-depth information regarding water feature construction, techniques and maintenance, please visit: www.atlanticwatergardens.com/university/awguniversity.html... - Page 3 FilterFalls Skimmer PS3900 BF1600 Removable Sturdy top grate removable lid Support bar Support bar Matala ® Media bag filter mat Dual Bio-Tech Stainless steel filter mats framed debris High density Bottom grate polyethylene enclosure Solid lip and molded inserts Cut-off step fittings for 1-1/2”...
-
Page 4: Water Gardens
Water Gardens POND VOLUME It is important to calculate the estimated water volume before you begin construction, and then re-calculate final water volume when your project is completed. Estimating water volume pre-construction is a step that is often skipped by many homeowners and contractors. -
Page 5: Streambed Construction
STREAMBED CONSTRUCTION Using proper streambed construction techniques can limit the transitional water needed to fill the streambed and enables the system to function optimally. Transitional water is determined by the height that the weir rock extends above the liner at the spillway opening. -
Page 6: Excavating And Setting The Ps3900
Skimmer body. The depth of excavation for the PS3900 should be 15” below water level. Do not dig too deep. The skimmer should be set on stable, compacted soil. In the case that you over-dig, be sure to compact the soil thoroughly to prevent settling. -
Page 7: Attaching The Weir Door
When you are finished, remove the spring clips and pull the liner away from the face of the skimmer. Apply a consistent bead of Atlantic fish-safe silicone to the face of the Skimmer along the centerline of the pre-drilled bolt holes. Once you are finished, you can return the liner to its original position and replace the spring clips. -
Page 8: Plumbing The Ps3900
BF1600. If 2” flexible PVC is being used for the supply line, replacing the 1 ½” HA1550 bulkhead with an Atlantic 2” HA2000 bulkhead (not included) is recommended. Remove the retaining nut and plastic friction washer, leaving the rubber gasket on the body of the bulkhead fitting. -
Page 9: Liner Attachment
FilterFalls and the back side of the liner are clean and free of debris. Apply a consistent bead of Atlantic fish-safe silicone to the face of the FilterFalls along the center line of the threaded inserts. -
Page 10: Pond-Free
Attach the liner flange to the FilterFalls, starting with the center screw first, and then work out toward the sides of the spillway. It may be necessary to first pierce the liner with a nail or an awl before inserting the screw. Do not fully tighten any screws until all the screws have been installed. -
Page 11: Excavating And Setting The Pv1700 (Waterfall)
Oasis Pump Vault Installation The PV1700 is Atlantic’s most compact, easy to install pump vault. The PV1700’s features include an incredibly strong enclosure, recessed panels on the front that can accommodate Triton 3-Way Diverters, cut lines on the back for 11/2” and 2” pump discharges, and marked drill points on the left and right sides for an Auto Fill. -
Page 12: Excavating And Setting The Pv1700 (Fountain)
EXCAVATING AND SETTING THE PUMP VAULT FOR A FOUNTAIN The capacity of the basin will vary depending on the size, height and number of the decorative fountain elements. For a general rule of thumb, make the basin at least twice the width of the fountain piece or fountain pieces at their widest point. -
Page 13: Setting The Sp1600
Oasis FastFalls Installation SETTING THE SP1600 Place the Oasis FastFalls on a level bed of undisturbed soil if possible, to avoid settling. If installing above existing grade, compact the area thoroughly. This critical step will ensure that the FastFalls will not settle out of level over time. Blocks or bricks set on virgin soil can also be used to raise the FastFalls while reducing the chance of settling. -
Page 14: Hiding The Sp1600
Apply Atlantic’s Silicone Sealant in a continuous, consistent bead along the center of the threaded inserts. Once completed, return the liner to its dry-fit position. Attach the supplied flange to the FastFalls, starting with the top screw first, working around the flange. -
Page 15: Skimmer/ Pump Vault Accessories
TR215CV. Place the TidalWave pump with installed Triton Check Valve into the PS3900 Skimmer. Connect the outlet fitting of the Triton Check Valve to the PVC supply line that feeds the waterfall using PVC glue and cleaner. -
Page 16: Af1000 Autofill Kit
A drill-point has been provided on the back of the Oasis Skimmer and Pump Vault to show the proper location and elevation to install an Atlantic HA2000 bulkhead fitting for the overflow (not included). See Figure K above for drill-point location. This combination will position the bottom of the overflow pipe approximately 1”...