Advertisement
1
2
1
a
2
4
3
SHD8850
6
5
7
um_shd8850_79_en_170428.indd
5-8
c
b
L
R
4
What's in the box
1) Headphones
4) AC/DC adaptor 5) 3.5 mm audio
Connect
Caution
• AAA alkaline batteries can be used to operate the headphones, but
cannot be charged with this system.
Note
• Only use Philips rechargeable shortened sleeve NimH batteries with your
headphones. Other types of rechargeable batteries cannot be charged
with this system.
• Before using the headphones for the first time, charge the supplied
batteries for at least 5 hours.
• If the volume of the audio source is insufficient, the transmitter
automatically turns off.
• The docking station does not transmit audio signal when you charge the
battery.
1 Connect the audio device (figure
• For devices with a 3.5 mm audio output, connect one side of
the supplied 3.5 mm audio cable to the 3.5 mm audio input
of the docking station and another side to the 3.5 mm audio
output. Then switch to AUDIO IN SELECT and switch ATT
• For devices with an RCA output, connect one side of an RCA
SHD8850
• For devices with an optical output (SHD8850 only), connect one
2 Connect the power adapter (figure
3 Pull the battery tape off before charging (figure
4 Charge the headphones (figure
Use your headphones
1 The headphones turn on automatically when you wear them on
your ears (figure
5
• For devices with a 3.5 mm audio output, turn up the volume
• You can also use the headphones with the supplied audio
2 When the batteries are old or defective, purchase and replace with
new rechargeable batteries with the same specifications (figure
LED indications
Status
Searching
Connection
established
Low volume level
Low battery level
Charging
Fully charged
* The white LED on docking station turns off after 5 minutes.
(figure
1
)
Sound indications
2) Docking station
3) user manual
6) Optical cable
Low battery level
cable
(SHD8850 only)
Reaching maximum volume level.
* The headphones beep twice and turn off after 5 minutes.
Technical data
General specification and
features
• music time (headphone
variation): minimum 20 hours
• Normal time for a full charge:
6 hours
• Operating range: up to 30 meters
• Optical input / 3.5 mm input
switch (SHD8850 only)
• 2.4 GHz RF solution
• Hi Res audio (for wired
connection only)
• Auto power on/off
• Attenuator on/off
2
)
Transmission
• Carrier / reception frequency:
2.406-2.472 GHz
For further product support, please visit
www.philips.com/support.
2 a
to 0dB (figure
).
adapter (sold seperately) to the RCA output of the audio device,
and another side to the supplied 3.5 mm audio cable. Connect
the remaining side of the 3.5 mm audio cable to the 3.5 mm
audio input of the docking station. Then switch to AUDIO IN
SELECT and switch ATT to -8dB (figure
2 b
).
side of the supplied optical cable to the optical output of the device,
and another side to the optical input of the docking station. Then
switch to OPTICAL SELECT (SHD8850 only ) (figure
2 c
).
3
).
4
).
5
).
6
).
level. If the volume is too low, the auto switch-on of your
headphones will not respond.
cable to connect to smart devices or for outdoor use (figure
8
LED on docking station
LED on headphones
N/A
Green LED flashing
White LED on
Green LED on
White LED flashing slowly*
N/A
N/A
Green LED flashing
slowly
Green LED flashing
N/A
Green LED on
N/A
1 beep per minute*
1 beep
• Transmission power: <10 dBm
Battery
• 2 x AAA NimH 900 mAh
rechargeable batteries
(Philips SBC HB900S)
Adapter
• Philips: YLJXA-A050055,
input: 100-240 v~, 50/60 Hz,
output: 5 vdc 550 mA
Weight and dimensions
• Headphones: 367 g
219 x 176 x 95 mm (H x W x D)
• Docking station: 190 g
74 x 174 x 142 mm (H x W x D)
28/04/2017
17:18:58
7
).
).
Advertisement
