Page 1
Model KUSB-488B USB to GPIB Converter Quick Start Guide KUSB-488B-903-01 Rev. A / March 2010 G R E A T E R M E A S U R E C O N F I D E N C E...
Page 3
Any unauthorized reproduction, photocopy, or use the information herein, in whole or in part, without the prior written approval of Keithley Instruments, Inc. is strictly prohibited. All Keithley Instruments product names are trademarks or registered trademarks of Keithley Instruments, Inc. Other brand names are trademarks or registered trademarks of their respective holders.
Quick Start Guide Welcome to Keithley Instruments product ownership We would like to thank you for choosing Keithley Instruments products for your electronic test and measurement needs. If you have any questions after reviewing this information, please contact your local Keithley Instruments representative or call Keithley Instruments corporate headquarters (toll-free inside the U.S.
(grounded at the same point as the antistatic mat). Inspection for damage The Model KUSB-488B was carefully inspected electrically and mechanically before shipment. After unpacking all items from the shipping carton, check for any obvious signs of physical damage that may have occurred during transit.
Model KUSB-488B USB to GPIB Converter Quick Start Guide Repacking for return shipment If you need to return the Model KUSB-488B for repair, carefully pack the unit in its original packing carton (or equivalent), and follow these instructions: • Request a Return Material Authorization (RMA) number either by calling the Keithley Instruments U.S.
Figure 2: KI-488 Driver CD installation screen Follow the prompts to complete the setup procedure. You may choose to install the Keithley command-compatible driver or the NI command-compatible driver. Refer to Models KPCI-488LPA and KUSB-488B Reference Manual (part number KI488-901-01) for available functions of either compatible driver.
Connect the Model KUSB-488B to the GPIB connector on the rear panel of the instrument. Plug the Model KUSB-488B USB cable into a USB port on your computer. The Found New Hardware dialog box will display on your computer screen.
Page 10
Hardware Wizard dialog box displays. Click Finish to complete the installation (see Figure Figure 6: Completing KUSB-488B Loader software installation The Found New Hardware Wizard will display again to initiate installation of the KUSB-488B software. Select No, not at this time, and then click Next (see Figure...
Page 11
Model KUSB-488B USB to GPIB Converter Quick Start Guide Figure 7: Found New Hardware Wizard dialog box Select Install the software automatically to initiate installation of the KUSB-488B software, and then click Next (see Figure Figure 8: Select automatic installation of KUSB-488B software When the KUSB-488B software installation is complete, the Completing the Found New Hardware Wizard dialog box displays.
Model KUSB-488B USB to GPIB Converter Quick Start Guide Troubleshooting If your system does not display the Found New Hardware Wizard after you plug the Model KUSB-488B cable into a USB port on your computer, unplug the cable and plug it into a different USB port (or plug it into the same port again).
Page 13
Make any desired changes to the configuration, then click OK. Figure 12: GPIB interface and bus configuration Save these configuration changes by selecting Setting > Save Configuration in the Keithley GPIB Configuration Utility window. KUSB-488B-903-01 Rev. A / March 2010...
To launch the diagnostic tool: From Microsoft Windows, select Start > All Programs. From the programs selection, select Keithley Instruments > KI-488 > KI-488 Diagnostic Tool. The KI-488 Diagnostic Tool window will open (see Figure 13).
GPIB commands previously sent or transmitted box. Next steps For detailed information about using the Model KUSB-488B USB to GPIB Converter in test and measurement applications, review the additional product documentation that is available on the Product Information CD-ROM that came with your Model KUSB-488B.
Page 16
Model KUSB-488B USB to GPIB Converter Quick Start Guide This page left blank intentionally. KUSB-488B-903-01 Rev. A / March 2010...
WARRANTY Keithley Instruments, Inc. warrants this product to be free from defects in material and workmanship for a period of one (1) year from date of shipment. Keithley Instruments, Inc. warrants the following items for 90 days from the date of shipment: probes, cables, software, rechargeable batteries, diskettes, and documentation.
Page 18
M E A S U R E C O N F I D E N C E Keithley Instruments, Inc. Corporate Headquarters • 28775 Aurora Road • Cleveland, Ohio 44139 • 440-248-0400 • Fax: 440-248-6168 • 1-888-KEITHLEY • www.keithley.com 12/06...