Related Manuals for Globel GL6000
Summary of Contents for Globel GL6000
- Page 1 Skillion Roof GARDEN SHED Assembly Instructions Suitable for Models: 5'w x 3'd 6'w x 3'd 6'w x 4'd 8'w x 3'd 8'w x 4'd © Globel Industries Pty Ltd GI00045 September 30 2015...
-
Page 2: Installation Advice
Phillips-head tip to make the assembly quicker and easier. Do not over-tighten self-tapping screws. Nuts can be tightened by holding your finger on them as you tighten the bolt with the power screw driver - no spanner needed. © Globel Industries Pty Ltd GI00045 September 30 2015... -
Page 3: Tools Required
TOOLS REQUIRED Battery Power Drill Step Ladder Phillips-Head Screw Driver Bit (P2) Tape Measure Dyna Bolts Masonry Steel (not supplied) Drill Bit Drill Bit 6.5mm x 36mm 6.5mm recommended © Globel Industries Pty Ltd GI00045 September 30 2015... -
Page 4: Parts List
Front Mid-Wall Brace (Right) Side Mid-Wall Brace Back Mid-Wall Brace Right Side Top-Wall Rail Left Side Top-Wall Rail Front Top Rail Back Top Rail Front Roof Trim Back Roof Trim Entry/Exit Ramp © Globel Industries Pty Ltd GI00045 September 30 2015... - Page 5 This product contains small parts. LEFT FRONT & BACK RIGHT FRONT & BACK TOP-WALL RAIL TOP-WALL RAIL BRACKET BRACKET DOOR GLIDE DOOR ROLLER DOOR SPACER ROOF DOOR HANDLE CORNER BRACE CORNER CAP SCREW BOLT WASHERS © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 6 FRONT FASCIA PANEL FRONT FASCIA PANEL FULL HALF (8' WIDE SHEDS ONLY) ROOF SHEET ROOF SHEET ABOVE DOOR FASCIA LEFT RIGHT ROOF STARTER ROOF STARTER DOOR BRACE LEFT GABLE RIGHT GABLE © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 7 RIGHT FRONT MID-WALL BRACE RIGHT SIDE BASE RAIL LEFT FRONT MID-WALL BRACE BACK MID-WALL BRACE SIDE MID-WALL BRACE BACK TOP-WALL RAIL LEFT TOP-WALL RAIL RIGHT TOP-WALL RAIL FRONT TOP RAIL ENTRY/EXIT RAMP © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 8 Then pour the concrete and allow five days to cure. Diagram C Diagram D F52 REINFORCING STEEL MESH Diagram E BUILDERS PLASTIC FORMWORK FORMWORK MESH RAISED TO REINFORCING FORMWORK APPROXIMATELY HALF STEEL MESH THICKNESS OF FORMWORK © Globel Industries Pty Ltd GI00045 September 30 2015...
-
Page 9: Pre-Assembly
FRONT FACE DOOR OF TOP RAIL GLIDE SLOT Diagram 2 FLANGE FRONT FACE OF TOP RAIL SLOT SLOT TOP RAIL (FRONT) DOOR GLIDE. NOTE: CURVED SIDE FACING FRONT FACE OF TOP RAIL © Globel Industries Pty Ltd GI00045 September 30 2015... - Page 10 TOP-WALL RAIL BRACKET RIGHT SIDE END WITH SCREW TOP-WALL SHARPER RAIL ANGLE NARROW SECTION TOP-WALL RAIL RIGHT FRONT SHARPER ANGLE END TOP-WALL RAIL BRACKET TOP-WALL RAIL SHARPER ANGLE END Diagram 3A © Globel Industries Pty Ltd GI00045 September 30 2015...
-
Page 11: Sliding Doors
Doors for 5' wide sheds have only 5 holes along top edge and 5 holes along bottom edge. DOOR DOOR DOOR SPACER DOOR SPACER BOTTOM OF DOORS DOOR BRACE © Globel Industries Pty Ltd GI00045 September 30 2015... - Page 12 BASE RAIL Step 2 Attach corner braces to each end of the back BACK base rail, and secure to side base rails as shown BACK BASE RAIL in Diagram 1A. Diagram 1A © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 13 See Diagram 3. IMPORTANT: RIGHT Holes at each end on the thin face SIDE of the side mid-wall brace MUST BASE RAIL FRONT face upward. Diagram 3 © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 14 CORNER RAIL PUSH back rail using two screws PANEL LEFT SIDE WALL per panel, as shown in TOP-WALL SHEET Diagram 6. RAIL BRACKET © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 15 BRACE four screws as shown in Diagram 8A. BACK MID-WALL BRACE Repeat for right side. LEFT SIDE INSIDE VIEW MID-WALL BRACE OF LEFT BACK CORNER PANEL BACK Diagram 8A © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 16 TOP-WALL FRONT NUT & the corresponding far right and left corners. RAIL BOLT GABLE - RIGHT SIDE See Diagram 12. (FRONT VIEW) © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 17 6' WIDE x 4' DEEP SHED: 8' WIDE x 4' DEEP SHED: FULL 1 2 FULL 1 2 FULL 1 2 DOORS FULL FULL FULL FULL FULL FULL BETWEEN BACK SIDES BACK SIDES SIDES BACK FRONT © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 18 SLIDES IN BEHIND FRONT EDGE RIGHT CORNER PANEL OF FULL FRONT WALL SHEET CORNER PANEL BACK PRISE UP FRONT CORNER PANEL AWAY FROM FRAME RIGHT FRONT CORNER Diagram 15 RIGHT FRONT CORNER © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 19 BRACE corner brace and SIDE four screws MID-WALL as shown in BRACE Diagram 18. FRONT Repeat for left side. INSIDE VIEW OF RIGHT FRONT CORNER PANEL Diagram 18 © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 20 Shown Diagram 19A DOOR JAMB Diagram 20 Step 16 ENTRY/EXIT RAMP Attach the entry/exit ramp to the front base rail, and secure using six screws. See Diagram 20. FRONT BASE RAIL © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 21 IN PLACE roof starter and into the top edge of the back top rail as shown in Diagram 22. Repeat procedure for left side roof starter. See Diagram 23. FRONT Diagram 23 © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 22 5' WIDE 6' WIDE 8' WIDE 2 x full roof sheets 2 x full roof sheets, 1 x half roof sheet 3 x full roof sheets, 1 x half roof sheet © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 23 Diagram 27. NOTE: FRONT Roof corner cap fits OVER roof trim. Washers are not required for this step. BACK ROOF Diagram 27 CORNER © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 24 Diagram 30. (iv) Repeat the procedure (i to iii) for the right side door. Diagram 30 GENTLY PUSH DOOR LEFT DOOR IN BEHIND JAMB DOOR JAMB © Globel Industries Pty Ltd GI00045 September 30 2015...
- Page 25 BOTTOM re-tightening. HOLES DOOR GLIDE Step 24 DOOR FASCIA PANEL Fit the door fascia panel to the front top rail, using four screws as shown in Diagram 32. DOORS Diagram 32 © Globel Industries Pty Ltd GI00045 September 30 2015...
-
Page 26: Additional Notes
Ensure floor is free of dust and debris and apply silicone on inside of shed, along the edge of the base rail and to the floor. Dyna Bolt 6.5mm x 36mm © Globel Industries Pty Ltd GI00045 September 30 2015... -
Page 27: Warranty Clause
You must have a copy of your original purchase receipt if warranty is required. Globel Garden Sheds are built for the purpose of domestic use only and must be installed according to the steps and procedures in the assembly instructions booklet herewith. - Page 28 © Globel Industries Pty Ltd GI00045 September 30 2015...
Need help?
Do you have a question about the GL6000 and is the answer not in the manual?
Questions and answers