Table of Contents
Advertisement
Quick Links
I
M
P
O
R
T
A
N
T
I
M
P
O
R
T
A
N
T
o
Always perform initial inspections including visual, current and airflow (Figure A) tests before servicing a heater.
o
Check the AC cord, wires and plugs, for cut, pinched or exposed wires, secure connection and proper location.
o
NEVER touch the glass portion of a heating element. Always visually inspect the elements and perform a resistance test.
o
The heating elements are wired in 3 parallel circuits and are suggested to be replaced in pairs for this reason. (FIGURE B)
S
P
E
C
I
F
I
C
A
T
I
O
N
S
S
P
E
C
I
F
I
C
A
T
I
O
N
S
o
Current: 12.5 – 14 amps in "HIGH" mode
o
Airflow: 640+ FPM
o
Power: 1500 Watts
o
Heating Elements (Bulbs): 14 +/- 5%
o
Heat Rise: 140 (over ambient temperature)
N
O
P
O
W
E
R
N
O
P
O
W
E
R
o
Check (in order)
1. Power transformer
2. Front control board (and fuse)
3. Heat sensor (high limit switch)
o
If the heater turns on then immediately off, inspect the thermostat sensor, its wires and connection.
o
Inspect the wiring and cables and their connections including the AC cord and its ground.
L
I
M
I
T
E
D
H
E
A
T
/
N
O
L
I
M
I
T
E
D
H
E
A
T
/
N
O
o
Visually inspect the heating elements and their connections. Turn on the heater and look for non-working elements.
o
Test the resistance of the heating elements. They should measure 14 +/- 5% (13.3 – 14.7).
o
Replace a heating element if the glass or the ceramic ends are cracked or broken, overly discolored, if the quartz element
appears to be damaged or if the wire insulation is excessively whitened (more than 1/4") near the bulb. (FIGURE F)
o
Test the unit with a new thermostat sensor.
o
Remove the leads to the high limit switch and perform a continuity test. If any resistance, replace.
o
Test the unit with a new circuit board.
O
V
E
R
H
E
A
T
I
N
G
/
H
E
O
V
E
R
H
E
A
T
I
N
G
/
H
E
o
Check the fan to make sure the fan is spinning freely, properly aligned and not binding.
o
Visually inspect the fan for built up dust and dirt. Clean it with a firm-bristled brush and vacuum.
o
Inspect the fan bearing and oil it if needed.
o
Test/replace the fan sensor.
o
Test/replace the high limit switch.
L
O
U
D
F
A
N
L
O
U
D
F
A
N
o
Visually inspect the fan to make sure the cage and motor are properly mounted, aligned and spinning freely.
o
Inspect the fan bearing and oil it if needed.
o
Inspect the fan bushing. Make sure it fits tightly in the blower fan and on the motor shaft.
o
If the fan continues to make noise, it may be bent or out of balance and need replaced.
*
*
D
I
S
C
L
A
I
M
E
R
:
W
I
R
*
*
D
I
S
C
L
A
I
M
E
R
:
W
I
R
1000XL / SunTwin 1500 Elite Troubleshooting Guide
H
E
A
T
/
F
A
N
N
O
H
E
H
E
A
T
/
F
A
N
N
O
H
E
A
T
N
O
F
A
N
A
T
N
O
F
A
N
E
C
O
L
O
R
S
,
C
O
N
N
E
C
T
O
E
C
O
L
O
R
S
,
C
O
N
N
E
C
T
O
A
T
A
T
R
S
,
P
A
R
T
S
A
N
D
T
H
E
I
R
R
S
,
P
A
R
T
S
A
N
D
T
H
E
I
R
L
O
C
A
T
I
O
N
S
A
R
E
S
U
B
J
E
L
O
C
A
T
I
O
N
S
A
R
E
S
U
B
J
E
C
T
T
O
C
H
A
N
G
E
*
*
C
T
T
O
C
H
A
N
G
E
*
*
Page 1
Advertisement
Table of Contents
Related Manuals for EdenPURE SunTwin 1500 Elite
Summary of Contents for EdenPURE SunTwin 1500 Elite
- Page 1 1000XL / SunTwin 1500 Elite Troubleshooting Guide Always perform initial inspections including visual, current and airflow (Figure A) tests before servicing a heater. Check the AC cord, wires and plugs, for cut, pinched or exposed wires, secure connection and proper location.
- Page 2 1000XL / SunTwin 1500 Elite Troubleshooting Guide (FIGURE A) AIRFLOW TESTING (FIGURE B) BULB PAIRING – Bulbs are wired in 3 series of pairs and should be replaced in pairs accordingly. (Figure C) LARGE WIRING BLOCK (FIGURE D) FRONT CIRCUIT BOARD...
Need help?
Do you have a question about the SunTwin 1500 Elite and is the answer not in the manual?
Questions and answers
What problem is indicated by 6 beeps when a Sun Twin 1509 Elite unit is turned on?