Solid Strike EVO Owner's Manual

Downhill bike

Advertisement

Solid Bikes Europe Rudolf-Diesel-Straße 13 D-72250 Freudenstadt
Owner's Manual Solid Strike EVO
Congrats on your new Solid Strike EVO Downhillbike!!
You've decided to go for a expertly engineered, high spec DH machine. Technical work and bike
Maintenance need to be performed by specifically trained personnel.

Adjustability of the frame

The Solid Strike has been designed for the use of 27.5"-wheels. Rear wheel travel is 203 mm / 8".
We recommend the use of fork that is designed for the use of 27.5"-wheels and has a travel of
around 200 mm.
If you have purchased a new Solid Strike Evo as a complete bike, a suitable fork is already installed.
When taking your new Solid out of the box, the stem needs to be mounted to the upper fork crown
and the pedals need to be fitted to the cranks.

Assembly of stem on upper fork crown:

-
Apply medium strength screw locking system (e.g Loctite)
-
Tighten the screws which attach the stem to the upper fork crown with a torque of 7Nm

Mounting of the pedals

-
Please consider that the left pedal is equipped with a left-handed thread – it needs to be
tightened counterclockwise. The right pedal possesses a regular thread, meaning it can be
tightened clockwise.
-
Tighten your pedals with a torque of 38 to 43 Nm at the cranks (if there are no different
information available from the manufacturer). Please consider also all other claims by the
manufacturer and use the washers included in the package and apply some grease on the
thread in order to avoid contact corrosion.

Tires

CAUTION: Some models of the Solid Strike Evo are equipped tubless as standard, i.e. on these bikes,
there is no tube inside the tire. In case you purchased one of our tubeless-models (e.g. Solid Strike
Evo Factory), please consider the following:
This technology deriving from racing saves weight and leads to a better flex behaviour of the tire.
Unfortunately, tubeless tires are never 100% sealed – this is why you should check your tire pressure
before riding.
Solid Bikes Europe
T +49 (0) 7441 / 952-450
Inhaber Peter Schmid
F +49 (0) 7441 / 952-451
Rudolf-Diesel-Straße 13
info@solidbikes.de
D – 72250 Freudenstadt
www.solidbikes.de
Sie erreichen uns Montag bis Freitag von 8:00 Uhr bis 13:00 Uhr und von 14:00 Uhr bis 17:15 Uhr

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Strike EVO and is the answer not in the manual?

Questions and answers

Summary of Contents for Solid Strike EVO

  • Page 1 200 mm. If you have purchased a new Solid Strike Evo as a complete bike, a suitable fork is already installed. When taking your new Solid out of the box, the stem needs to be mounted to the upper fork crown and the pedals need to be fitted to the cranks.
  • Page 2 The total rear wheel travel of the Solid Strike EVO is 203 mm, 30% of that is 60.9 mm. Approx 61 mm corresponds to a stroke of 19.5 mm at the piston rod of your shock. Please DO NOT set your bike with a sag of 23 mm (=30% of 76 mm), because this will lead to too much sag and overly soft suspension.
  • Page 3 Solid Bikes Europe Rudolf-Diesel-Straße 13 D-72250 Freudenstadt Disassembly of the rear wheel For the disassembly/removal of the rear wheel, please proceed in the sequence as follows: Remove M6 counter screw on drive side (4-mm hex key) (1) Loosen radial clamping screw(pinch bolt) on non drive side (4-mm hex key) (2) Loosen axle from non-drive-side via 6-mm hex key and take out (3) Assembly is performed the other way around.

Table of Contents