Icom UR-FR5100 Instructions

INSTRUCTIONS
CHANNEL EXTENSION MODULES
UR-FR5100
UR-FR6100
SUPPLIED ACCESSORIES
q DC power cable ...................................................1
w Control cable ........................................................1
e Angles ..................................................................2
r Screws (M4×8 mm) ..............................................4
t Set screws (M3×6 mm) ........................................4
y Tapping screws (M3×8 mm) .................................2
q w
e r
t y
Icom, Icom Inc. and the logo are registered trademarks of Icom Incor-
porated (Japan) in the United States, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
All other products or brands are registered trademarks or trademarks of
their respective holders.
T h a n k yo u fo r p u r c h a s i n g t h e U R - F R 5 1 0 0 /
UR-FR6100 .
CHANNEL EXTENSION MODULES
Please read these instructions and repeater's
instruction manual carefully before installation and
operation.
OPENING CASE
q Remove 7 screws from top and 2 screws each
from both sides of the repeater, then slide off the
top cover to the direction of the arrow as illustration
below.
P 0 P 0
P 1 P 1
P 2 P 2
P 3 P 3 P 4 P 4
w Remove 3 screws from bottom and 2 screws each
from both sides of the repeater.
P 0 P 0
P 1 P 1 P 2 P 2
P 3 P 3
P 4 P 4
e Disconnect the control cable from the channel
module (original), then remove the front panel.
Channel module Channel module
(original) (original)
Front panel Front panel
P 0 P 0
P 1 P 1
P 2 P 2
P 3 P 3
P 4 P 4
r Remove 6 screws from the front panel, then re-
move the shielding plate and rubber seal.
Shielding plate Shielding plate
Rubber seal Rubber seal
INSTALLATION
• Install the UR-FR5100 or UR-FR6100
(channel extension module)
q Attach the supplied angles to both sides of the
channel extension module, and tighten the 2 sup-
plied screws (M4×8) on each side.
w Install the channel extension module using the sup-
plied screws (Tapping screws: M3×8, Set screws:
M3×6) as shown below.
Set screws Set screws
Channel extention Channel extention
Tapping Tapping
module module
screws screws
Channel module Channel module
(original) (original)
• Connect the control cable
q Connect the supplied control cable to J502 on the
front board as shown below.
w Cut the rubber caps of the control cables, then in-
sert the rubber caps to the front panel's chassis as
shown below.
q q w w
J502 J502
ASSEMBLE THE UNIT
q Replace the rubber seal and shielding plate of the
front panel, then tighten the 6 screws.
• Make sure the rubber seal is properly seated in the
groove of the chassis.
• Be sure to match the correct positions of the holes of
the shielding plate and projections of the front panel's
chassis.
Holes Holes
Rubber seal Rubber seal
Projections Projections
w Connect the control cables to the channel modules.
Channel extention module Channel extention module
Channel module Channel module
(original) (original)
Longer cable Longer cable
(upper side) (upper side)
Shorter cable Shorter cable
P 0 P 0
P 1 P 1
P 2 P 2
P 3 P 3
P 4 P 4
(lower side) (lower side)
e Return the front panel, top cover and screws to
their original positions.
P 0 P 0
P 1 P 1
P 2 P 2
P 3 P 3
P 4 P 4
P 0 P 0
P 1 P 1
P 2 P 2
P 3 P 3 P 4 P 4