Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Dust Networks D2120
- Page 1 Dust Networks D2120 Evaluation Kit Quick Start Guide...
- Page 2 Trademarks Dust Networks, the Dust Networks logo, and SmartMesh are trademarks of Dust Networks, Inc. All third party brand and product names are the trademarks of their respective owners and are used solely for informational purposes. Copyright This documentation is protected by United States and international copyright and other intellectual and industrial property laws. It is solely owned byDust Networks, Inc.
-
Page 3: Table Of Contents
2 SmartMesh Manager Description ....................7 Connections ..................... 8 Technical Specifications ..............8 Regulatory Information ..............9 3 Setting Up a Network Setting Up the SmartMesh Manager ......... 11 Setting Up the Network ............... 11 D2120 E VALUATION UICK TART UIDE... - Page 4 ABLE OF ONTENTS D2120 E VALUATION UICK TART UIDE...
-
Page 5: About This Guide
About This Guide This guide provides information required to successfully demonstrate the capabilities of the D2120 Evaulation Kit. It provides various pinout and connector information for attaching sensors to a mote Evaluation Module and instructions for setting up a network. - Page 6 1 - A Conventions Used HAPTER BOUT UIDE Body. D2120 E VALUATION UICK TART UIDE...
-
Page 7: M2020 Evaluation Module
M2020 Evaluation Module This chapter provides specifications for the M2020 Evaluation Module (M2020-EVM) provided in the D2120 Evaluation Kit. The M2020-EVM can be used as a reference design for integrating an M2020 Mote into a self-contained device. M2020 Evaluation Module The M2020-EVM consists of an M2020-A Mote, packaged with an antenna, battery holder, status LEDs, I/O connectors, and a recessed reset switch. -
Page 8: Connector P1
0 to 5 V inputs, and contains internal filter circuitry for 60 Hz noise. Table 1-1. P1 Connector Pinouts Number Pin Name Description Analog input 1 (0–50) Ground Analog input 2 (0–50) Ground Warning: Reverse biasing these inputs may result in damage to the device. D2120 E VALUATION UICK TART UIDE... -
Page 9: Connector P2
Analog input 3 Note: All I/O, including UART, are at LVTTL (3 V) signaling levels. An external level converter is required for RS-232 communications. Warning: Reverse biasing these inputs may result in damage to the device. D2120 E VALUATION UICK TART... -
Page 10: Serial Interface
Source Sink Total I/O Storage temperature –40 °C Operating ambient –40 °C temperature Warning: The M2020 Mote is an ESD-sensitive device. Use caution when handling in order to prevent permanent damage to the device. D2120 E VALUATION UICK TART UIDE... -
Page 11: Recommended Operating Conditions
Avoid handling the module by its antenna. For best results, place all devices so that the antenna points to the ceiling. Devices placed close to the ground may have a significantly reduced range. In the event of communications difficulties, try changing the orientation of the module. D2120 E VALUATION UICK TART... -
Page 12: Regulatory Information
(2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Unauthorized modification or changes not expressly approved by Dust Networks™ Inc. could void compliance with regulatory rules, and thereby your authority to use this equipment. D2120 E VALUATION UICK TART UIDE... -
Page 13: Smartmesh Manager
SmartMesh Manager This chapter describes the D2120 SmartMesh Manager provided in the D2120 Evaluation Kit. The D2120 is used to configure and control a network of M2020 motes, and provides data and configuration information via an XML/RPC interface. Description The D2120 SmartMesh Manager consists of a single board computer and an M2020 mote. -
Page 14: Connections
—Used for connection to a LAN or direct connection to a 10/100 Ethernet port computer using the cross-over cable provided in the D2120 Evaluation Kit. Refer to the SmartMesh Manager Administration Guide for information on configuring the IP address of the SmartMesh Manager. -
Page 15: Regulatory Information
MART ANAGER Regulatory Information The FCC ID: SJC-D2120. This device complies with Part 15 o the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. - Page 16 2 - S Regulatory Information HAPTER MART ANAGER D2120 E VALUATION UICK TART UIDE...
-
Page 17: Setting Up A Network
Setting Up a Network This chapter describes how to set up a D2120 Evaluation Kit in a simple sensor network. For a more detailed explanation, see the Getting Started Guide that came with your Evaluation Kit. Setting Up the SmartMesh Manager A Install the SmartMesh Console software. - Page 18 3 - S Setting Up the Network HAPTER ETTING ETWORK D2120 E VALUATION UICK TART UIDE...
Need help?
Do you have a question about the D2120 and is the answer not in the manual?
Questions and answers