Page 1
PRODUCTION RELEASE & REVISION DESCRIPT’N/BUYER DWG No PATRS No. DATE INITIAL ----------------- 50303290 Y.K.CHA D.G.KIM 07-18-12 ----------------- 50303290 Y.K.CHA D.G.KIM 09-04-12 내용변경 INSTRUCTION MANUAL REV.B 6p, 7p, 11p, 15p 내용수정 ECO (재고소진 후 변경) DNR Super High Resolution Day & Night Color Camera 148(+/-5)mm 50301270 / 81x24(mm)
Page 2
INSTRUCTION MANUAL DNR Super High Resolution Day & Night Color Camera Please read this manual thoroughly before use and keep it handy for future reference.
WARNINGS AND CAUTIONS TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT. CAUTION CAUTIO RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK).
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
FCC COMPLIANCE STATEMENT INFORMATION TO THE USER: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL...
CONTENTS OF PACKAGE Installation of the camera must be performed by qualified service personnel in accordance with all local and national electrical and mechanical codes. Carefully remove the color camera and its accessories from the carton and verify that they were not damaged in shipment. The contents of the package includes : 1.
INTRODUCTION The camera provides high-quality images using SONY 1/3” CCD and digital Signal process LSIs. Features: ● 1/3" EXview HAD CCD Ⅱ for an image of high sensitivity ● 2.6-6 mm(F1.6-2.4) / 4-9 mm(F1.6-2.4) /3.6mm fixed (f 3.0) ● Digital Wide Dynamic Range (Xtended Dynamic Range) ●...
CAMERA CONNECTION 1. Lens : 2.6-6mm / 4-9mm/3.6mm fixed lens for wide area monitoring 2. Power : power source from a DC 12V 3. Video : BNC connector used to connect the camera to a monitor, switcher.ect.
INSTALLATION 1.Make mounting holes and cable hole in the place (ceiling or wall) to which this dome camera is installed using the Drilling guide label.
Page 10
2. Turn open the dome window counterclockwise. 3.Fasten Mounting screws(2X) and align the dome camera with it like above picture. Turn the dome camera to left direction about 16 degree. 4.The assembly of the dome window is reverse order of disjointing. Finally, lock dome window with locking screw(M2X4) in a accessory kit.
OSD ADJUSTMENT The tact switch allows both navigation and changes to the OSD Menu. To enter into the OSD menu push centrally on the joystick and navigate using the up, down, left and right actions. If there is an arrow to the right of the menu function, this denotes that there is an accessible sub menu function.
OSD MAIN MENU TREE SETUP MENU (page 1) LENS SHUTTER/AGC LENS SHUTTER/AGC AUTO IRIS AUTO WHITE BAL MANUAL MANUAL BACKLIGHT PICT ADJUST MOTION DET RETURN RETURN NEXT (page2) EXIT SAVE ALL WHITE BALANCE BACKLIGHT PUSH USER 1 USER 2 ANTI CR MANUAL PUSH LOCK RETURN...
Page 13
SETUP MENU (page 2) PRIVACY PRIVACY DAY/NIGHT DAY/NIGHT AREA SEL AUTO CAMERA ID COLOR COLOR SYNC TRANSP LANGUAGE MOSAIC CAMERA RESET BACK (page 1) EXIT SAVE ALL RETURN RETURN CAMERA ID SYNC NR MODE (titling) Y LEVEL C LEVEL RETURN RETURN RETURN LANGUAGE...
OSD MENU SETTINGS LENS MANUAL Manual lens only AUTO TYPE (DC / VIDEO) Sets the type of mechanical iris (Video lens is not supported) MODE (OPEN / CLOSE / AUTO) Sets the type of control to be applied over the mechanical iris. SPEED (0 –...
Page 15
WHITE BAL ATW (Auto Trace White balance) SPEED (0~255) Adjusts the pull-in speed of ATW. DELAY CNT (0~255) Sets the time-based hysteresis of ATW. ATW FRAME (X0.5/X1/X1.5/X2) Sets the pull-in frame magnification. ENVIROMENT (indoor/outdoor) Preset for either indoor or outdoor applications of the ATW PUSH Wide range Auto White Balance mode (AWB) USER1 &...
Page 16
ATR (Adaptive Tone Reproduction) allows adjustment of the image to assist with widely contrasting scenes of view. LUMINANCE (LOW/MID/HIGH) Sets the extent of the luminance compression CONTRAST (LOW/MIDLOW/MID/MIDHIGH/HIGH) Sets the extent of the contrast enhancement MOTION DET DETECT SENSE (0~127) Sets the motion detection sensitivity (0=low sensitivity, 127=high sensitivity) BLOCK DISP (OFF / ON / ENABLE) Applies a Motion block trace in the selected area.
Page 17
COLOR (1~8) Sets the colors of the privacy zones. TRANSP (0.00/0.50/0.75/1.00) Sets the transparency of the privacy zone area if color is selected. MOSAIC (ON/OFF) Sets the mosaic function as the privacy to ON or OFF. (Note: when ON, transparency needs to be set at 0.00 and privacy zones can only be 1 color OR mosaic and not mixed) DAY/NIGHT AUTO...
Page 18
CAMERA ID Sets the camera ID to ON or OFF. A title of 26 characters per line can be applied. Use the joystick to navigate the cursor. Pushing centrally on the joystick will allow selection of that character. The arrows at the bottom allow you to move the cursor without changing the character.
AUTO WHITE DEFECT Push the left button for 5 seconds and enter Auto white defect menu. Cover the lens and Enter for starting. If white defects are over 65pcs, the camera is faulty and auto defect is useless. Over 70'C Auto white defect can't be activated. LENS ADJUSTMENT (OPTIONAL VARIFOCAL LENS) Lens 2 ~ 6mm...
SPECCIFICATIONS MODEL NTSC Power source DC 12V ± 10% Power Power consumption 2.0 Watts ( 160mA ) Image sensor 1/3″ SONY EXview HAD CCD II Total pixels 1020(H) x 508(V) 1020(H) x 596(V) Effective pixels 976(H)x494(V) 976(H)x582(V) Scanning system 2:1 Interlace 15.734KHz(H) Scanning frequency 15.625KHz(H) x 50Hz(V)
Page 25
DNR Super High Resolution Day & Night Color Camera 50303290B PRINTED IN KOREA...