Table of Contents
Advertisement
Quick Links
TS-14-I-0714
E-SPTS-I-0809
EQUIPMENT DEVELOPMENT CO., INC.
Operator's Instruction Manual
TS-14
14" ELECTRIC SELF PROPELLED TILE STRIPPER
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: 301-638-3326 • 301-663-1600
Fax: 800-447-3326 • 301-663-1607
EQUIPMENT DEVELOPMENT CO., INC.
edcoinc.com • sales@edcoinc.com
Advertisement
Table of Contents
Summary of Contents for Edco TS-14
- Page 1 TS-14-I-0714 E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC. Operator’s Instruction Manual TS-14 14” ELECTRIC SELF PROPELLED TILE STRIPPER 100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA Phone: 301-638-3326 • 301-663-1600 Fax: 800-447-3326 • 301-663-1607 EQUIPMENT DEVELOPMENT CO., INC. edcoinc.com • sales@edcoinc.com...
- Page 2 TS-14-I-0714 EQUIPMENT DEVELOPMENT CO., INC. READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT. Death or serious injury could occur if this machine is used improperly. SAFETY SAFETY MESSAGES • Do not disconnect power by pulling cord. To disconnect, grasp the plug, not the cord.
-
Page 3: Table Of Contents
Specifi cations & dimensions are for HOW TO ORDER REPAIR PARTS reference only and subject to change. To insure product safety and reliability, always use genu- ine EDCO replacement parts when making repairs to the Length (L) 35.4” 91.44 cm equipment. -
Page 4: Safety Guideline
Death or serious injury can result if this machine is used improperly. Safety Guidelines Eye and ear protection must be worn at all times while the TS-14 is in use. During normal operation, sound pressure levels less than 85dBA. Use only ANSI approved safety glasses to help prevent eye injury. -
Page 5: Operating Instructions
The TS-14 may be used on concrete and/or wood surfaces and operates on standard household current. Do not use the TS-14 for any purpose other than that for which it was designed. Do not modify the machine. -
Page 6: Cutting
Loosen but do not remove the bolts shown in (Figure 6) from the bottom side of the striker plate. • Inspect the new EDCO blade and observe blade angle as in (Figures 4 & 5) above. • Carefully slide the old blade out and replace with the new EDCO blade or rotate blade if changing surfaces. -
Page 7: Machine Operation
TS-14-I-0714 E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC. Machine Operation: • Make sure the power switch on the machine is in the OFF position before proceding. Plug the machine into an electrical outlet. The blade drive starts as soon as the machine is switched on by pressing the black button. -
Page 8: Maintenance
Lubricate the wheel bearings from time to time with an occasional drop or two of light oil to prevent binding. • Keep the TS-14 clean. • Be sure the safety decals are readable and properly maintained on the machine. Quick Reference... -
Page 9: Notes
TS-14-I-0714 E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC. NOTES ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ This page intentionally left blank. Page 9 800-638-3326 • edcoinc.com • sales@edcoinc.com... -
Page 10: Notes
TS-14-I-0714 EQUIPMENT DEVELOPMENT CO., INC. NOTES ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ This page intentionally left blank. Page 10 800-638-3326 • edcoinc.com • sales@edcoinc.com... -
Page 11: Limited Equipment Warranty
*Seller reserves the right to hold shipments against past due accounts. EDCO will, at its option, repair or replace, at the EDCO factory or at a point designated by *Seller reserves the right to alter payment terms. - Page 12 E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC. SURFACE PREPARATION, RESORATION, PROFESSIONAL SAWING EQUIPMENT & HAND HELD TOOLS 100 THOMAS JOHNSON DRIVE, FREDERICK, MD 21702 PHONE: 800-638-3326 OR 301-663-1600 Fax: 800-447-3326 or 301-663-1607 Email: sales@edcoinc.com Website: edcoinc.com Patents Pending & Issued Created 5 2014 Printed in USA ©2014 800-638-3326 •...
Need help?
Do you have a question about the TS-14 and is the answer not in the manual?
Questions and answers