Advertisement
Quick Links
Quick start guide
Care Call passive infra red (PIR) movement monitor
Movement Activation
Use the following guide to set up your monitor to illuminate zone one on your Pager or SignWave when triggered.
For advanced settings please refer to instructions overleaf.
Configuration switches
1
2
3
4
5
6
7
CCM3A-2216-EU-PIR-MKX
8
MOVEMENT MONITOR 11/12/13
9
USE MAINS POWER SUPPLY
10
11
PS3A-2207-UK ONLY
12
SILENT ALERT SA3000 SYSTEM
13
WWW.SILENT-ALERT.CO.UK CLOFIELD LTD. UK
14
TEL 01246 260045
15
16
CCM3A-2216-EU-PIR-MKX
MOVEMENT MONITOR 11/12/13
USE MAINS POWER SUPPLY
PS3A-2207-UK ONLY
SILENT ALERT SA3000 SYSTEM
WWW.SILENT-ALERT.CO.UK CLOFIELD LTD. UK
TEL 01246 260045
Power Supply socket
2.
The test button will flash amber /
green on start up, then flash
amber for up to 30 seconds whilst
the movement sensor stabilises.
This is normal.
Sound Activation
It is possible to enable sound monitoring as well as movement detection. Audio trigger delays can be used to reduce false
alarms from transient noise (door slams etc).
1.
Move keys 5 & 7
to the right.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
WARNING! Your device and its accessories are not toys. They may contain small parts. Keep them out of the reach of small children.
CCM3A-2216-EU-PIR
Audio spindle
Test button
PP3 battery clip
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Passive
infra red
movement
sensor
3.
Position the unit & adjust the sensor
2.
Turn the spindle on the side of the
monitor half a turn clockwise until the
A good way to test the unit is to
whistle about 2 metres away from it.
More sensitive
Any questions? Call us on 01246 450789
1.
to cover the area you wish to
monitor. Ensure the unit is at least
40cm from the floor & fix to the wall
with the screws and wall plugs
provided. Use the keyhole slots in
the back of the unit to secure.
38mm
slot is horizontal.
Less sensitive
Move Key 16 to the right. Connect the power
supply
(PS3A-2207-UK)
the cable around the strain relief. Plug the
power supply into a mains socket.
If mains failure monitoring is required connect
a 9V Alkaline PP3 to the battery clip.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
40 - 70cm
3.
The test button will light amber
when a sound is detected and
change to green once it has
Switches 7 & 8 alter the
short
1
2
3
4
5
6
7
8
Care
Call
into the unit, looping
CCM3A-2216-EU-PIR-MKX
MOVEMENT MONITOR 11/12/13
USE MAINS POWER SUPPLY
Alkaline
PS3A-2207-UK ONLY
SILENT ALERT SA3000 SYSTEM
WWW.SILENT-ALERT.CO.UK CLOFIELD LTD. UK
TEL 01246 260045
been accepted.
delay period.
long
medium
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
Advertisement
Summary of Contents for Care Call CCM3A-2216-EU-PIR
- Page 1 CCM3A-2216-EU-PIR Care Call Care Call passive infra red (PIR) movement monitor Any questions? Call us on 01246 450789 Movement Activation Use the following guide to set up your monitor to illuminate zone one on your Pager or SignWave when triggered.
- Page 2 NOTE: In most cases it is not necessary to change the system code. However, when one or more systems are in close proximity, system codes can be used to avoid interference from other Care Call systems using up to a maximum of 16 channels. The monitor is supplied with no system code switches set (system code 1).
- Page 3 Advanced Settings CCM3A-2216-EU-PIR Care Call Care Call passive infra red (PIR) movement monitor Any questions? Call us on 01246 450789 Disarm the Carer Alerts It is now possible to disarm the PIR sensor and audio monitoring feature when not required.
Need help?
Do you have a question about the CCM3A-2216-EU-PIR and is the answer not in the manual?
Questions and answers