Table of Contents
Advertisement
Quick Links
Limited Warranty Statement
Infinity warrants this product to be free against defects in materials and
workmanship as follows:
Labor: For a period of two years from date of purchase, if this product
is determined by Infinity to be defective, Infinity will repair and/or re-
place the product with a new or rebuilt unit or repair at no charge. After
the warranty period, you must pay for all labor and parts charges. Cus-
tomer to ship the radio pre-paid via UPS ground to Infinity for evalua-
tion. Infinity then will credit the UPS costs at its sole option. If the radio
is found to be defective under warranty, Infinity will repair/exchange
per the above policy, sending the unit back freight prepaid to Cus-
tomer. If found to be a customer caused problem or abused and out-
side of above warranty, customer to pay for freight charges to and
from factory plus repair charges at current published repair rates.
Parts: If a warranty issue, Infinity to supply at no charge, new or rebuilt
replacements for defective parts for a period of two years. After the
warranty, standard repair or replacement rates apply.
SERVICE: To obtain warranty service, you must communicate with
Infinity directly, and then once an RMA Return Materials Authorization
Number is received, to ship it back in its original carton, or in packag-
ing offering an equal degree of protection, to Infinity, freight prepaid
with insurance.
This warranty does not cover the battery which has a one year pro-
rated warranty, nor does it cover customer instruction, installation, set-
up, programming, adjustments or signal reception or transmission.
This warranty does not cover any units which have been previously
altered, repaired, or serviced by anyone other than Infinity or used with
accessories not approved by Infinity. This warranty does not cover
cosmetic damage or damage due to acts of god, accident, misuse,
negligence, or modification to any part of the product
This warranty does not cover products sold AS-IS or with FAULTS.
No particular merchantability of this product is implied or stated.
Proof of purchase in form of a bill of sale or receipted invoice, evi-
dence that the unit is within the warranty period and must be pre-
sented to obtain warranty service. Warranty is offered only if a WAR-
RANTY REGISTRATION CARD has been filled out and sent to Infinity,
either by Mail or Email, with 15 days of purchase. This warranty is in-
valid if the factory serial number applied has been altered or removed
from the Product. Re-Sellers may have additional Warranty State-
ments
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY
IS THE EXCLUSIVE REMEDY OF THE CONSUMER. INFINITY SHALL
NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAM-
MAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY
ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY APPLI-
CABLE LAW. ANY IMPLIED WARRANTY OR MERCHANTABILITY OR
FITNESS FOR A PARTICUAL PURPOSE ON THIS PRODUCT IS NOT
MADE OR IMPLIED BY INFINITY.
40
WARNING!
Read the instruction manual completely before use.
-Install the antenna first and then the battery as
pictured in the manual.
-Charge the battery 14-24 hrs before use even if
the green LED on the charger is present, this to
condition the battery. DO NOT OVERCHARGE!
-DO NOT install the battery or use the radio with
out the proper antenna attached.
Failure to perform these steps may damage the
radio and void the warranty. Warranty card needs to
be returned for warranty to be validated.
Kirmuss & Associates
Worldwide Technologies Direct
Infinity Advanced Technologies
1340 West 43rd Drive, Unit 11
Golden, Colorado, USA 80403
tel: 303 263 6353
© 2005-2008 Specifications subject to change without notice. Failure to read and follow-
ing the guidelines established in the manual may void warranty. Restricted to Public
Safety, Fire/EMS use. License to operate is required. Customer is solely responsible for
full compliance with local, state and federal laws regarding product usage. Tampering or
modifying unit voids FCC Approval and Warranty.
P1000/1010/1045
Standard and P Series
VHF or UHF
User's Manual
Note: Pager function is pro-
grammed only via programming
s/w. Requires additional pro-
gramming software and cable.
fax: 303 862 7170
Rev08-04-01
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Infinity P1000
Summary of Contents for Infinity P1000
- Page 1 UPS ground to Infinity for evalua- Standard and P Series tion. Infinity then will credit the UPS costs at its sole option. If the radio is found to be defective under warranty, Infinity will repair/exchange...
-
Page 2: To Our Valued Customers
To our Valued Customers: Once configured to send out a Page: Thank-you for purchasing an INFINITY two way portable transceiver. 1. Select the channel to the Group or Team or Mem- Designed in the USA, built in Hong Kong, this robust, compact, easy to... - Page 3 FCC RF exposure guidelines. Antennas & Batteries Use only Infinity supplied and approved antennas and batteries. The Tone Frequencies Use of non approved accessories and attachments as well as for both Encode (Call)
- Page 4 Using your Paging Radio About Infinity: Infinity radios are sold only through Infinity or Infinity authorized regional resellers. The radio is also field Typically your radio will have one paging channel . programmable using the keypad (if enabled by the software),...
- Page 5 Product Features How to use your Paging Radio 128 channels Once programmed, your radio software programming for the Paging Receive model should look similar to the screens below. This illustra- 5 watt (VHF), 4 watt (UHF) power output tion is a sample scenario of a Chief’s radio.
- Page 6 Step 13: Once all the required parameters have been entered, Unpacking (Kit contents) Click on “File”, then “Save As”, and name the file. Flexible Antenna Step 14: Handheld Transceiver With the radio fully charged, NOW TURN THE RADIO ON. Step 15: Click on “Program”, “Write to Radio”, and Start.
- Page 7 Programming 2 Tone Decode (pager function) Transceiver Preparation: IMPORTANT Only available in P Series Radios Continued. The factory does not charge the battery before shipping. Follow these instructions precisely. Failure to insert the battery as shown will see the pins on the back of the radio pushed in, causing intermittent contact with the battery.
-
Page 8: Getting To Know Your Radio
Setting the 2 TONE PAGER Receive (Requires P Option radio) Getting to Know your Radio Channel Selector Set to 2 tone dB Gain (Selector also used for scrolling Flex Antenna through programming steps when in front keypad program- ming mode) Speaker On/Off Mic Element... - Page 9 Setting ANI, MONITOR button Set to PD1200 for MDC1200 Protective (Fleet sync for plastic film on Kenwood) LCD display. This should be removed when radio is placed in service This sets the MONI Button Set ANI ID, function to end or open up squelch beginning of TX.
-
Page 10: Radio Controls
NOTE: (1750 Hz) over the air, to be heard by In the P VERSION for 2 another Infinity brand radio. This acti- Tone Decode, this key may vates an audible chime on the receiv- be configured in the s/w to ing Infinity radio. -
Page 11: Lcd Screen
Step 9: Double click on the “Infinity” icon on LCD Screen Infinity.lnk the desktop to run the s/w Step 10: Once the software is up and running, on the main screen and under the “Type Setting”, select the radio model number in the drag down option. - Page 12 (or the same transmit and receive frequency between radio users, the word “infinity”. (The serial number for the radio is lo- sometimes called Radio to Radio); and over a REPEATER (where...
-
Page 13: Quick Step Guide
Example: One may have both the Fire Dept. and EMS on the Quick Step Guide same frequency. During standard operations, one may not want Step 1: Insert the “P1000 Infinity Software” CD into the CD to hear the other. The two-way radio receiver's audio turns on drive bay of your computer. - Page 14 You may use either the front keypad to program the radio, or use English Channel Alias name. the Infinity Model PG-1 (serial) or PG-2 (USB) programming cable inserted in the microphone jack which is connected in turn to a Volume and Squelch: The transceiver has a preset squelch level, PC or laptop using the Infinity programming software.
- Page 15 Flank Keys Taking Care of your handheld Transceiver The portable transceiver has the capability to allow the user to create alarms as well as to easily make changes on the Your transceiver has been designed using the latest in technology along with high temperature flame retardant plastics.
- Page 16 Common Radio Concepts Flank Keys, con’t Understanding Squelch: The radio typically with a clear chan- PRIORITY (PRI) CHANNEL SCAN: By assigning certain nel is silenced. Upon reception of a carrier from another trans- channels during radio programming (using the keypad or s/w) ceiver or repeater, and with CTCSS/DCS programmed to accept to be considered as PRIORITY channels, press MENU, press a programmed and valid tone, only then does the receiver hear...
- Page 17 Other: Audible Voice Feedback: The radio may announce in plain English audibly through the unit’s speaker the vari- ous functions and channel numbers of the radio to the User. To enable this unique feature: Press MENU, then rotate the channel selector until VOICE? 14 is displayed on the LCD.
- Page 18 Note: Regarding the selection of the CTCSS, DCS or NO TX/ RX tone (s), in Tone Menu (line 3), previous page, by press- USER MENUS FOR RADIO OPERATION ing the “* LOCK” key toggles you between the options: No Tone, CTCSS Tones, DCS Digital Tones, No Tones, etc. Once you have selected the desired function feature, (No Tone, CTCSS analog Tone, DCS Digital Tone), Press ENTER, and then Rotate the Channel Selector until to see the appropriate Tone for that Channel,...
- Page 19 USING THE FRONT KEYPAD TO PROGRAM THE RADIO Troubleshooting Notes: 1) If your radio “transmits by itself”, make sure that the VOX (voice (For 2 tone decode, programming done using software only) activated switch) is turned off. The tree below guides you through the various line items that you 2) If you cannot hear a station using a repeater calling you, yet you may program per radio channel.
- Page 20 Entering the Radio Programming Before Programming your radio: Mode using the Front Keypad Ensure that before programming your radio either using the front keypad or software that you first write down on a paper the following information that will be needed, this prior Step 1: With the radio turned off, to programming: MONI...
Need help?
Do you have a question about the P1000 and is the answer not in the manual?
Questions and answers