RIDGID EB44241 Operator's Manual page 33

Repair Parts
Parts List For RIDGID Oscillating Edge Belt/Spindle Sander
RIDGID parts are available on-line at www.ridgidparts.com
Always order by Part Number—Not by Key Number
Key
Part No.
No.
1 826358-1
2 805553-2
3 822304
4 See pg. 29
5 825808
6 See pg. 29
7 810993-2
8 825841
9 830291
10 805297-9
11 825523
12 825548
13 825844
14 825842
15 830246
16 825537
17 825852
18 159572-138
19 808380-7
20 825840
21 830456
22 159572-186
23 824604
24 830290
25 805549-22
* Standard Hardware Item - May be purchased locally
† These parts are available where you purchased your sander.
• Any attempt to repair this motor may create a hazard unless repair is done by a qual-
ified service technician. Repair service is available at your nearest Authorized Ser-
vice Center.
Model EB44241
Description
Knob, Spindle
Washer
21/64 x 5/8 x 1/32
Drum, Sanding 3/4"
†Drum, Sandpaper
Plate, Throat 2"
†Belt, Sanding 4" x 24"
Screw, Set Half Dog
10/32 x 1/2
Adapter, Throat Plate
Fan
Screw, Flat Hd
1/4-20 x 5/8
Table, Rear
Plate, Wear
Nut, Special Twin 1/4-20
Screw, Shoulder 1/4-20
Chute, Sawdust
Bracket, Table Lock
Knob, 1/4-20 x 3/4
Screw, Wash/Hd
Ty "T" 10-32 x 3/8
Screw, Pan Hd 10-14 x 1/2
Spring, Detent
Base
Screw, Hex Hd
Ty "T" 1/4-20 x 1
Screw, Hex Wash/Hd
Ty "T" 8-32 x 3/8
• Motor/Drive Asm
Washer
13/64 x 3/8 x .031
Figure 1
Key
Part No.
No.
26 826801
27 825854
28 819012
29 9416630
30 829785
31 AC1000
32 817399-11
33 37837
34 825549
35 825537-1
36 825543
37 825524
38 803309-2
39 825525
40 825539-1
41 SP6496
42 37836
43 —
44 805553-30
45 805553-24
46 822304-1
47 822304-2
48 822304-3
49 825808-1
50 825808-2
51 825808-3
33
Description
Enclosure
Cord w/Plug
Foot
Screw, Hex Hd Ty "T"
5/16-18 x 1
Switch, Locking
†Key, Switch
Relay
Wrench, Hex "L" 5/32
Spacer, Table Lock
Bracket, Table Lock Left
Bolt, Table Lock
Table, Front
Screw, Soc Set Lock
10-32 x 3/8
Plate, Stop
Knob 1/4-20
Owners Manual
Wrench, Hex "L" 3/32
Belt Sanding Assembly
(See Fig. 2)
* Washer 5/8 x 1-3/4 x 1/8
Washer
21/64 x 7/8 x 3/64
Drum, Sanding 1"
Drum, Sanding 1-1/2"
Drum, Sanding 2"
Plate, Throat 1-1/2"
Plate, Throat 1"
Plate, Throat 1/2"