Subscribe to Our Youtube Channel
Summary of Contents for Alpha WMP-ND02
- Page 1 Manual 11n Wireless LAN CARD 11N 無線網卡 Model Number : WMP-ND02 Alpha Networks Proprietary and Confidential Information...
-
Page 2: Product Features
Dynamic date rate of IEEE 802.11n scaling from MCS – 0 to MCS –15 as shown in Appendix I Ÿ Supports wireless data encryption with 64/128 bit WEP for security Ÿ Support WPA and WPA2 enhanced security Ÿ Drivers support Linux 2.4.6 Ÿ RoHS complaint Alpha Networks Proprietary and Confidential Information... -
Page 3: Functional Block Diagram
5.15 ~ 5.35GHz and 5.47~5.725GHz for Japan Ÿ 5.15 ~ 5.35GHz and 5.47 ~ 5.725GHz for Europe Ÿ 5.725~5.850GHz for China Ÿ 2.2.1.4 Channel 9 channels for US Ÿ Numbers 8 channels for Taiwan Ÿ 2.2.1.5 Data Rate 6,9,12,18,24,36,48,54Mbps Alpha Networks Proprietary and Confidential Information... - Page 4 IEEE 802.11g Ÿ 2.2.3.2 Radio and BPSK, QPSK, 16QAM, 64QAM with OFDM Modulation Type Ÿ 2.2.3.3 Operating 2400 ~ 2483.5MHz ISM band Frequency Ÿ 2.2.3.4 Channel 11 channels for United States and Canada and Taiwan Alpha Networks Proprietary and Confidential Information...
- Page 5 For 5GHz 8 for draft 802.11n (20MHz) 3 for draft 802.11n (40MHz) From MCS – 0 to MCS –15 as shown in Appendix I Ÿ 2.2.4.5 Data Rate Ÿ 2.2.4.6 Media Access CSMA/CA with ACK Alpha Networks Proprietary and Confidential Information...
-
Page 6: Software Requirements
Security Supports enhanced security WEP, 802.1x, WPA and WPA2. 2.4.1 Information Feature Detailed Description Ÿ General 2.4.1.1 General Information shows the name of Information Wireless Adapter, Adapter MAC Address, Regulatory Domain, Firmware Version, and Alpha Networks Proprietary and Confidential Information... - Page 7 STA with WEP off will never associate any AP with WEP enabled Ÿ WEP Key Format: Option for Hex format Ÿ 2.4.3.3 802.1x Support EAP-TLS, EAP-TTLS, and EAP-PEAP Ÿ 2.4.3.4 WPA/WPA2 Support WPA/WPA2-PSK and WPA/WPA2-EAP Ÿ Support Cipher Mode AES and TKIP Alpha Networks Proprietary and Confidential Information...
-
Page 8: Mechanical Requirements
802.11a/b/g/n product Ÿ WHQL 2.6.2 Meet applicable WHQL certification requirements Ÿ Physical Layer and 2.6.3 Meet ALPHA Engineering Test Plan and Test Functionality Report 2.7 Requirements of Reliability, Maintainability and Quality Feature Detailed Description Ÿ 2.7.1 MTBF Mean Time Between Failure > 30,000 hours Ÿ... - Page 9 Alpha Networks Proprietary and Confidential Information...
- Page 10 Appendix I: Rate Dependent Parameters for High Throughput . Modulation and Coding Schemes (MCS) The parameters in the table are: ■ Rate: Rate in Mbps ■ NES: Number of FEC encoders used ■ NSD: Number of Data Subcarriers ■ NCBPS: Number of Code Bits Per Symbol (total of all spatial streams) ■...
- Page 11 Test Equipment/測試設備列表 English EQUIPMENT Q’TY IQ-View Shielded Box (530 * 280 *160 mm) made of Copper Splitter (1 * 3) RF CABLE PC (with monitor) USB 2.0 / PCI / MINI PCI / CARD BUS Interface (HIROSE / IPEX) Test connect Fixed Attenuator (20dB) Power supply 中文...
- Page 12 Test Environment Diagram/測試環境圖示 Splitter (1 對 3) IP: 192.168.100.254 （Note：For IQ-View / IQ-Flex）...
- Page 13 Normal Test Operating Procedure/一般作業用測試操作程序 1. Testing Steps: 6 steps in total 1. 測試步驟: 共 6 個步驟 註 1:測試前請先安裝待測物之 driver. 註 2:測試前請先依照附錄(Test Programming Setup & Test Program Install step / 測試程式設定和測試環境架設說明)設定 [Step 1] Run ”ATEToolRT28xx” at DUT (see Figure 1) to open test window (see Figure 2). [步驟...
- Page 14 [Step 2] Select test model, Then Kevin W.O Number and Serial number and Worker ID and Site Name. (see Figure 3) [步驟 2] 選取測試 Model 並鍵入工單號碼及 Serial Number 和測試人員及測試站別(如圖 3) (Figure 3) 選取測試 Model 鍵入工單號碼及 Serial Number 和測試人員及測試站別...
- Page 15 [Step 3] (a) Plug DUT into USB 2.0 / PCI / MINI PCI / CARD BUS Interface (MAIN) (b) Plug RF Cable on DUT antenna point. [步驟 3] (a) 將待測物插入 USB 2.0 / PCI / MINI PCI / CARD BUS Interface 介面。 (b) 將待測物接上測試線於天線端。...
- Page 16 [Step 5] When test finish, it will show “PASS”(see Figure 5). [步驟 5] 當測試完成,會出現’’PASS”的視窗(圖 5)。 (Figure 5) [Step 6] When show “PASS”, click “OK” and change the next one to continue [步驟 6] 出現 PASS 畫面，按 OK 鍵並換下一片繼續[步驟 2]到[步驟 5]。...
- Page 17 Test Program setup / 測試程式設定 [步驟 1] 按下程式中”Config” 選項 (如圖 1)，並輸入密碼 “ ”。 admin(測試用) (如圖 2) (Figure 1) (Figure 2)
- Page 18 [步驟 2] 仿照以下圖形及數據去設定程式，完成後按下”ok” 註 1: 請 Import 檔案(1WMPND02..A1G.ini)進來,一樣可完成參數設定 註 2: Tx Power Calibration(11g)(Path Loss 請依當時 Cable loss 填入) 註 3: Local IP 與 Server IP 請依照產線電腦 IP 及產線 SFCS Server 設定...
- Page 19 Test Program Install step / 測試環境架設說明 1.將測試設備接線完畢 2.準備乾淨的 windowsXP 環境 3.將測試程式複製至資料夾中 4.安裝測試程式資料夾內的 ANIO Protocol Driver 資料夾裡所附的 ANIO.exe 5.安裝待測物網卡的驅動程式 6.Calibration 測試環境,測試時加入一衰減器 20dB 測試. 7.開始進行測試...
- Page 20 F ed er al Co m mu n i c ati o n Co mmi ssi o n I n t erf er en c e Sta te men t This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
- Page 21 This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna, For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool.
- Page 22 2) this device must accept any interference, including interference that may cause undesired operation of the device This device has been designed to operate with an antenna having a maximum gain of 3.21dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.
- Page 23 以下警語適用台灣地區： 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更 原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無 干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信 或工業、科學及醫療用電波輻射性電機設備之干擾。 在 5.25-5.35 秭赫(GHz)頻帶內操作之無線資訊傳輸設備，限於室內使用。 本模組於取得認證後將依規定於模組本體標示審合格籤，並要求平台上標示 「本產品內含射頻模組：ID 編號」...
Need help?
Do you have a question about the WMP-ND02 and is the answer not in the manual?
Questions and answers