Table of Contents
Advertisement
OPERATOR'S MANUAL
18 Volt 1/2 in. (13 mm) Hammer Drill
R841150
Two Speed/Reversible
R
This new drill has been engineered and manufactured to our high standards for dependability, ease of operation, and operator
safety. When properly cared for, the drill will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator's manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
®
X
Advertisement
Table of Contents
Related Manuals for RIDGID R841150
Summary of Contents for RIDGID R841150
- Page 1 18 Volt 1/2 in. (13 mm) Hammer Drill R841150 Two Speed/Reversible This new drill has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When properly cared for, the drill will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
-
Page 2: Table Of Contents
INTRODUCTION The 18 Volt Cordless Hammer Drill has many features for making the use of this product more pleasant and enjoyable. Safety, performance, and dependability have been given top priority in the design of this product making it easy to maintain and operate. -
Page 3: General Safety Rules
■ Use battery only with charger listed. MODEL BATTERY PACK R841150 130254003 ■ Do not abuse the cord. Never use the cord to carry the charger. Keep cord away from heat, oil, sharp edges, or moving parts. Replace damaged cords im- mediately. -
Page 4: Specific Safety Rules
GENERAL SAFETY RULES SERVICE ■ Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury. SPECIFIC SAFETY RULES ■ ■ ■ ■ ■ Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. -
Page 5: Important Safety Instructions For Charger
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. ■ Never use a battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion. -
Page 6: Symbols
SYMBOLS Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME Volts Amperes Hertz Minutes Alternating Current Direct Current... -
Page 7: Specifications
The hammer drill has a two-speed gear train designed for drilling or driving at LO (1) or HI (2) speeds. A slide switch is located on top of your drill to select either LO (1) or HI (2) speed. FORWARD/REVERSE SELECTOR... -
Page 8: Features
FEATURES DEPTH GAGE KEYLESS CHUCK DIRECTION OF ROTATION SELECTOR (FORWARD / REVERSE / LOCK OFF [CENTER LOCK POSITION] ) BATTERY STORAGE PACK TORQUE ADJUSTMENT RING DUAL PORT CHARGER 4-1/8 in. Fig. 1... -
Page 9: Unpacking
■ Do not discard the packing material until you have care- fully inspected and satisfactorily operated the tool. ■ If any parts are damaged or missing, please call 1-866-539-1710 for assistance. PACKING LIST 1/2 in. (13 mm) Two Speed Hammer Drill Charger Battery Pack (2) Auxiliary Handle Double-ended Bit Operator’s Manual... -
Page 10: Operation
OPERATION WARNING: Do not allow familiarity with the hammer drill to make you careless. Remember that a careless frac- tion of a second is sufficient to inflict severe injury. CHARGING BATTERY PACK The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. - Page 11 OPERATION LED FUNCTION OF CHARGER See Figure 3. INDICATOR Power Power Corriente Alimentation Evaluate Evaluate Evaluate Evaluer Evaluar Evaluate Evaluate Charging Charging Cargando En charge Full Full Completo Charge max. POWER INDICATOR EVALUATE INDICATOR BATTERY PACK Without battery pack Hot battery pack Flashing Cold battery pack Flashing...
- Page 12 OPERATION TO INSTALL BATTERY PACK ■ Lock the switch trigger on the drill by placing the direction of rotation (forward-reverse) selector in center position. See Figure 4. ■ Place battery pack in the drill. Align raised rib on battery pack with the groove inside the drill. See Figure 5.
- Page 13 Your drill has a two-speed gear train designed for drilling or driving at LO (1) or HI (2) speeds. A slide switch is located on top of your drill to select either LO (1) or HI (2) speed. When using drill in the LO (1) speed range, speed will decrease and unit will have more power and torque.
- Page 14 10. ■ Tighten the chuck jaws on the drill bit. ■ To tighten the chuck jaws on drill bit; grasp and hold the collar of the chuck with one hand, while rotating the chuck body with your other hand.
- Page 15 INSTALLING DEPTH GAGE ROD See Figures 11 and 12. A depth gage rod has been packed with your hammer drill to assist you in controlling the depth of drilled holes. When drilling holes with the depth gage rod installed, the...
- Page 16 If not prepared, this loss of control can result in possible serious injury. When drilling metals, use a light oil on the drill bit to keep it from overheating. The oil will prolong the life of the bit and increase the drilling action.
- Page 17 DRILLING OPERATION ■ When drilling large holes in metal, we recommend that you drill with a small bit at first, then finish with a larger bit. Also, lubricate the bit with oil to improve drilling action and increase bit life.
-
Page 18: Maintenance
MAINTENANCE WARNING: When servicing use only identical RIDGID ment parts. Use of any other parts may create a hazard or cause product damage. GENERAL Avoid using solvents when cleaning plastic parts. Most plas- tics are susceptible to damage from various types of com- mercial solvents and may be damaged by their use. - Page 19 MAINTENANCE ■ Open the chuck jaws and remove the hex key. Remove the chuck screw by turning it in a clockwise direction. See Figure 18. Note: The screw has left hand threads. ■ Insert the hex key in the chuck and tighten chuck jaws securely.
-
Page 20: Warranty
Warranties for other RIDGID products may vary. HOW TO OBTAIN SERVICE To obtain service for this RIDGID tool, you must return it, freight prepaid, to an authorized RIDGID service center for hand held and stationary power tools. You may obtain... - Page 21 NOTES...
-
Page 22: Customer Service Information
Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgidwoodworking.com.